Page 2
Products described in this Document, which may include licenses obtained from third parties. ● Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part of this Document may be excerpted, copied, translated, or modified in whole or in part by any means without written permission.
Page 3
Barrier Gate User Manual NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. ● YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY...
Page 4
Barrier Gate User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance Caution degradation, or unexpected results.
Barrier Gate User Manual Chapter 1 Introduction 1.1 Product Introduction Barrier gate (hereinafter referred to as “device”) is the entrance and exit management device to limit motor vehicle passing. It can control the boom pole automatically via parking lot management system. Or you can control the boom pole via buttons on remote controller. Barrier gate is widely applicable to toll station, parking lot, the entrance and exit of community and unit, etc.
Barrier Gate User Manual Diagram Name Quantity Chuck Spindle rod screw set 4 Layer Expansion screw L-type wrench 1.3 Barrier Gate Overview Note The appearances of the devices vary with different models. The figure below just takes an example. Refer to the actual device for details.
Barrier Gate User Manual Figure 1-1 Barrier Gate Overview 1.4 Machine Core Structure After you open the front cover, you can see the machine core of the device host. Figure 1-2 Machine Core Structure...
Barrier Gate User Manual Table 1-2 Machine Core Component Description Description Description Spring hook hole Spring hook Rocker Cap screw to tighten the output shaft Output shaft Machine core limited block Linkage arm Spring upper pull rod Spring extension nut Crank arm Spring lower pull rod Hand wheel...
Barrier Gate User Manual Table 1-3 Octagonal Straight Boom Pole Packing List Item Quantity Octagonal Straight boom pole 1 1.5.2 Boom Pole with Strip Light Figure 1-4 Boom Pole with Strip Light Table 1-4 Boom Pole with Strip Light Packing List Item Quantity Boom pole with strip light 1...
Barrier Gate User Manual 1.5.3 Anti-collision Cylinder Boom Pole Figure 1-5 Anti-collision Cylinder Boom Pole Table 1-5 Anti-collision Cylinder Boom Pole Packing List Item Quantity Anti-collision cylinder boom pole M8 cap nut M8 × 75 hex socket head cap screw 1...
Barrier Gate User Manual Table 1-7 Fence Boom Pole Packing List Item Quantity Fence boom pole Pull rod joint component 1 1.5.6 Folding Boom Pole Figure 1-8 Folding Boom Pole Table 1-8 Folding Boom Pole Packing List Item Quantity Sub-boom pole Main boom pole Pull rod Joint component to connect main boom pole and pull rod 1...
Barrier Gate User Manual Chapter 2 Installation 2.1 Installation Environment The installation position of the barrier gate should meet the customer’s requirements and the following requirements. ● The installation space should be large enough to guarantee the boom pole can rise or fall normally.
Page 16
Barrier Gate User Manual Figure 2-1 Mark Position Note The suggestions for positions of holes: ● The holes in vertical direction should be near to the switch. ● If the entrance/exit is unidirectional, the holes should be in the horizontal center of the refuge island.
Page 17
Barrier Gate User Manual Figure 2-3 Open Front Cover 4. Fix the host. 1) Put the layers on the host bottom and keep them perpendicular to the barrier gate’s switch. 2) Put the host on the positions of expansion screws on the refuge island to make the screws pass through the layers.
Barrier Gate User Manual Figure 2-4 Fix Host Danger Keep the supporting bracket of the boom pole vertically upward to avoid accident caused by accidental rotation. 2.3 Install Boom Pole 2.3.1 Install Octagonal Straight Boom Pole Steps 1. Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts.
Page 19
Barrier Gate User Manual Figure 2-5 Unscrew Assembling Bolts 2. Install the chuck to the boom pole with the bolts as shown in the figure below. Figure 2-6 Install Chuck 3. Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.
Barrier Gate User Manual Figure 2-7 Fix Octagonal Straight Boom Pole 2.3.2 Install Boom Pole with Strip Light Steps 1. Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts. Save the components and parts for the following installations. Figure 2-8 Unscrew Assembling Bolts 4.
Page 21
Barrier Gate User Manual Figure 2-9 Install Chuck and Cushion Blocks 5. Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts. Figure 2-10 Fix Boom Pole with Strip Light 6.
Page 22
Barrier Gate User Manual Figure 2-11 Remove Rubber Plug 7. Wire the strip light cable. 1) Take the M12 white waterproof joint out from the accessory package. 2) Fix the waterproof joint to the cable hole on the host with the fixing nut. 3) Remove the waterproof cover from the joint, and thread the strip light cable through the waterproof cover, waterproof joint, and fixing nut.
Barrier Gate User Manual Figure 2-12 Wire Strip Light Cable 2.3.3 Install Anti-collision Cylinder Boom Pole Steps 1. Stuff the boom pole in the spindle rod aslant as shown in the figure below. Align the installation hole on the boom pole with that on the spindle rod.
Page 24
Barrier Gate User Manual Figure 2-13 Stuff Boom Pole Aslant 2. Insert the M8 × 75 hex socket head cap screw into the installation hole, and push the boom pole into the spindle rod quickly according to the directions as shown in the figure below. Figure 2-14 Install Anti-collision Cylinder Boom Pole 3.
Barrier Gate User Manual Figure 2-15 Fix Boom Pole 2.3.4 Install Octagonal Telescopic Boom Pole Steps 1. Install the octagonal telescopic boom pole. 1) Pull the sub-boom pole out according to the direction shown in the figure below. Align the installation holes on the main boom pole and sub-boom pole.
Page 26
Barrier Gate User Manual 3) Remove the end cover of the sub-boom pole. Insert the anti-fall adhesive tape into the sub-boom pole. After the anti-fall adhesive tape is inserted to the limit position, cut the projecting adhesive tape. Figure 2-18 Insert Anti-Fall Adhesive Tape 4) Install the end cover to the sub-boom pole.
Barrier Gate User Manual Figure 2-21 Install Chuck 3) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts. Figure 2-22 Fix Octagonal Telescopic Boom Pole 2.3.5 Install Fence Boom Pole Installation Procedure Steps...
Page 28
Barrier Gate User Manual Figure 2-23 Install Pull Rod Joint Component 2. Install the fence boom pole. 1) Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts. Save the components and parts for the following installations. Figure 2-24 Unscrew Assembling Bolts 2) Install the chuck to the boom pole with the bolts as shown in the figure below.
Page 29
Barrier Gate User Manual Figure 2-25 Install Chuck 3) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.
Page 30
Barrier Gate User Manual Figure 2-26 Fix Fence Boom Pole to Spindle Rod 4) Power off the device. Pull the fence boom pole to the horizontal position. Connect the pull rod of the joint component to the joint 2 of the fence boom pole pull rod. Wrest the pull rod of the joint component until the center boom poles are in the vertical position.
Barrier Gate User Manual Figure 2-27 Adjust Fence Boom Pole Note For the refuge island with a special height, drill holes by yourself to adjust the buffer rod height. Left and Right Directions of Fence Boom Pole When you look from the arrow direction as shown below, the right fence boom pole is the one that the center boom poles are on the left of the main boom pole, and the left fence boom pole is the one that the center boom poles are on the right of the main boom pole.
Page 32
Barrier Gate User Manual components and parts for the following installations. Figure 2-29 Unfasten Accessories of Main Boom Pole 2) Unfasten the cap nuts on the sub-boom pole and remove the screw, gaskets, and sub- boom pole pull rod joint. Save the components and parts for the following installations. Figure 2-30 Unfasten Accessories of Sub- Boom Pole 3) Force apart the sub-boom pole joint boards, and install the main boom pole.
Page 33
Barrier Gate User Manual can clip into installation holes on the sub-boom pole joint boards. Figure 2-32 Install Sub-Boom Pole Pull Rod Joint 2. Install the folding boom pole to the host. Note Here we take example of the right direction barrier gate. 1) Remove the plastic nut on the installation position of the right direction main boom pole pull...
Page 34
Barrier Gate User Manual rod joint. Figure 2-33 Remove Plastic Nut 2) Install the right direction main boom pole pull rod joint to the installation holes with the flat washer and spring washer. Figure 2-34 Install Main Boom Pole Pull Rod Joint 3) Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts.
Page 35
Barrier Gate User Manual Figure 2-35 Unscrew Assembling Bolts 4) Install the chuck to the boom pole with the bolts as shown in the figure below. Figure 2-36 Install Chuck 5) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.
Page 36
Barrier Gate User Manual Figure 2-37 Fix Folding Boom Pole 6) Power off the device. Pull the main boom pole to the horizontal position, and place the sub- boom pole nearly to the horizontal position. Wrest the pull rod between the sub-boom pole pull rod joint and the main boom pole pull rod joint.
Barrier Gate User Manual both ends. Figure 2-38 Connect Boom Pole to Host via Pull Rod 2.4 Wiring 2.4.1 Connect to Power Supply Connect the barrier gate to the power supply according to the figure shown below.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Power Adapter Nixie Tube Open Stop Close Learn Anti-fall Radar & Inductive Loop Figure 2-39 Connect to Power Supply 2.4.2 Connect to Supercapacitor Board Connect the barrier gate to the supercapacitor board as the figure shown below to realize that the boom pole can open automatically to let the vehicles pass when the power supply is cut off.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Supercapacitor Board (Ordered in Addition) Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Figure 2-40 Connect to Supercapacitor Board 2.4.3 Connect to Access ANPR Camera As the figure shown below, connect the opening control + and opening control –...
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Opening Access ANPR Control Camera Closing Control Figure 2-41 Connect to Access ANPR Camera 2.4.4 Connect to Traffic Signal Light Connect the live line to the COM interface of the barrier gate.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Connect to Red Light Connect to Green Light Null Line Live Line Figure 2-42 Connect to Traffic Signal Light 2.4.5 Connect to Anti-fall Radar Anti-fall Radar Wiring The anti-fall radar needs to be powered by 12 VDC power supply.
Page 42
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Anti-fall Radar Figure 2-43 Connect to Anti-fall Radar Radar Installation Instructions The anti-fall radar should be installed beside the barrier gate. In different scenarios, follow the instructions below to get the best effect.
Page 43
Barrier Gate User Manual Scenario 1: Small-Sized Vehicles For small-sized vehicles, such as the cars and SUVs, install the radar according to the figure shown below. Figure 2-44 Small-Sized Vehicles Scenario Scenario 2: Large-Sized Vehicles For large-sized vehicles, such as the oil tank trucks, transport vehicles, trucks, and other vehicles with chassises of higher than 1 m, install the radar according to the figure shown below.
Page 44
Barrier Gate User Manual Figure 2-45 Large-Sized Vehicles Scenario Scenario 3: Mixed Traffic For mixed traffic scenario, such as the large-sized and small-sized vehicles are mixing, install the radar according to the figure shown below.
Barrier Gate User Manual Figure 2-46 Mixed Traffic Scenario 2.4.6 Connect to Vehicle Detector Vehicle Detector Wiring Connect the C+ and C- interfaces of the barrier gate to the vehicle detector.
Page 46
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Anti-fall vehicle detector Live Line Vehicle Detector Null Line Anti-fall vehicle detector Figure 2-47 Connect to Vehicle Detector Vehicle Detector Installation Instructions The general width of the vehicle detector is 1 m.
Barrier Gate User Manual Figure 2-48 Vehicle Detector Installation 2.4.7 Connect to Active Infrared Intrusion Detector Connect the C+ interface of the barrier gate to the COM interface of the active infrared intrusion detector, and the C- interface of the barrier gate to the OUT interface of the active infrared intrusion detector.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Figure 2-49 Connect to Active Infrared Intrusion Detector 2.4.8 Connect to Arrow Indicator Connect the arrow indicator to the barrier gate as shown below.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Front Figure 2-50 Connect to Arrow Indicator 2.4.9 Connect to Strip Light For the boom pole with strip light, connect the strip light to the barrier gate as shown below.
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Strip Light Wire (Red) Strip Light Strip Light Wire (Yellow) Strip Light Wire (Green) Figure 2-51 Connect to Strip Light 2.4.10 Connect to Warning Light For the barrier gate with a warning light on the top of host, connect the warning light to the barrier gate as shown below.
Page 51
Barrier Gate User Manual HALL GND/485- 24V_IN A/B/C /485+/5V Vcc/u/v/w/Gnd Nixie Tube Open Stop Barrier Gate Close Control Board Learn Anti-fall Radar & Vehicle Detector Warning Light Wire (Black) 12 V Warning Light Wire (Red) Figure 2-52 Connect to Warning Light...
Barrier Gate User Manual Chapter 3 Parameters Configuration After the installation completes, power on the barrier gate, and it will operate self-check of opening to limit position. After the self-check completes, you can control the barrier gate via remote controller or buttons. 3.1 Remote Control After the self-check completes, you can control the boom pole to open, close, and stop via the remote controller leaving factory with the barrier gate.
Barrier Gate User Manual the fault codes appear on the nixie tube, it means there is operation error. Contact the technical personnel of our company to solve the problems. 3.2.2 Operation Procedure Refer to the table below for the description of the value on the nixie tube. Table 3-1 Nixie Tube Value Description Value Description...
Page 54
Barrier Gate User Manual 3. Press the Open/Close button on the control board to increase/decrease the value on the nixie tube. Adjust the value to “H4”. 4. Hold the Learn button on the control board until “PA” appears on the nixie tube. 5.
Page 55
Barrier Gate User Manual 4. Hold the Learn button on the control board to enter the menu settings. 5. Press the Open/Close button on the control board to adjust the value on the nixie tube. Note Adjust the value to 1 to enable the auto closing function, and 0 to disable the function. 6.
Page 56
Barrier Gate User Manual Note The actual auto closing time of the boom pole after the vehicle passes = the value shown on the nixie tube × 10 s. E.g., the value shown on the nixie tube is 3. Thus the actual auto closing time is 30 s.
Page 57
Barrier Gate User Manual away from the initial closing limit position. 3. Press the Learn button on the control board to save the settings. “00” will appear on the nixie tube. Press the Close button on the remote Closing Limit controller or press the Close button on Position the control board to adjust the boom...
Page 58
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Press the Open/Close button on the control board to increase/decrease the value...
Page 59
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Hold the Learn button on the control board.
Page 60
Barrier Gate User Manual 6. Press the Learn button on the control board to save the settings. “Hb” will appear on the nixie tube. Table 3-2 Boom Pole Type Value Description Value Boom Pole Type 2 m straight boom pole 3 m straight boom pole 4 m straight boom pole 5 m straight boom pole...
Page 61
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Press the Open/Close button on the control board to increase/decrease the value...
Page 62
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Press the Open/Close button on the control board to increase/decrease the value...
Page 63
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Press the Open/Close button on the control board to increase/decrease the value...
Page 64
Barrier Gate User Manual Press the Open button on the remote controller, press the Open button on the Opening Limit control board, or power on the device to Position adjust the boom pole to the opening limit position. Hold the Learn button on the control board. Press the Open/Close button on the control board to increase/decrease the value...
Barrier Gate User Manual Chapter 4 Maintenance 4.1 Adjust Boom Pole Balance Adjust the balance of the boom pole. Steps 1. Cut off the power supply. Rotate the hand wheel of the machine core to raise the boom pole to the position where the angle between the boom pole and the ground surface is 20°...
Barrier Gate User Manual Steps 1. Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts. Save the components and parts for the following installations. 2. Disassemble the boom pole and chuck. 3.
Barrier Gate User Manual Large octagonal boom pole 5 m octagonal straight Large spring with red hook × 1 spindle rod boom pole Small spring with green hook × 1 Large octagonal boom pole 6 m octagonal straight spindle rod boom pole Large spring with red hook ×...
Page 68
Barrier Gate User Manual assembling bolts. Save the components and parts for the following installations. 2. Disassemble the boom pole and chuck. Figure 4-3 Disassemble Boom Pole and Chuck 3. Unscrew the M12 fixing bolt of the spindle rod anticlockwise with a 10 mm hex wrench, and disassemble the bolt.
Barrier Gate User Manual Figure 4-5 Change Spindle Rod 5. Repeat the boom pole installation procedure to install a new boom pole. 4.3.3 Change Spring Before you start Cut off the power supply, and adjust the boom pole to the opening limit position. Steps 1.
Barrier Gate User Manual Note For different number of springs, operate according to the figure shown below. 4. Screw the spring extension nut into the spring upper and lower pull rods. Make sure that the protruding length of the spring upper pull rod to the extension nut (L1) and that of the spring lower pull rod to the extension nut (L2) is nearly the same.
Barrier Gate User Manual Figure 4-8 Change Machine Core 4.5 Left/Right Direction of Boom Pole The boom pole direction depends on the driving direction of the vehicle. When you look from the driving direction as shown below, the left boom pole is the one that the boom pole is on the left of the barrier gate host, and the right boom pole is the one that the boom pole is on the right of the barrier gate host.
Page 72
Barrier Gate User Manual Figure 4-9 Boom Pole Direction Instruction For some models of the barrier gate, the boom pole direction can be changed. For some models of the barrier gate, the boom pole direction cannot be changed. Refer to the figure below for the relationship between barrier gate models and boom pole directions.
Page 73
Barrier Gate User Manual Figure 4-10 Relationship Between Barrier Gate Models and Boom Pole Directions...
Barrier Gate User Manual 4.6 Change Left/Right Direction of Machine Core Before you start Cut off the power supply. Disassemble the machine core according to the procedure above. Steps 1. Disassemble the 2 cap screws to tighten the output shaft, the 2 cap screws to fix the limit positions, and the 1 cap screw to tighten the crank arm in sequence.
Page 75
Barrier Gate User Manual arm with a hammer or other tools. Rotate the crank arm 180°. Install the linkage arm and fix the circlips. Figure 4-13 Disassemble and Reinstall Crank Arm, Linkage Arm, and Rocker 4. Install the left-direction linkage arm component to the machine core with the rubber hammer. Fix the cap screws to fix the limit positions, the cap screw to tighten the crank arm, and the cap screws to tighten the output shaft in sequence.
Page 76
Barrier Gate User Manual Figure 4-15 Machine Core Installation Position 5. Change the trunking, power switch and installation board, and the positions of the air switch and spring to switch the left and right directions. Figure 4-16 Change Other Components 6.
Barrier Gate User Manual A. FAQ Fault Code on Fault Name Troubleshooting Remarks Nixie Tube “00” No error. No error. 1. Check if there is short circuit of the motor or the control Hardware 1. The barrier gate can “01” board.
Page 78
Barrier Gate User Manual 1. Check if the gear has lost Opening/Closing teeth. “0d” limit fault 2. Check if the opening/closing limit is damaged. Learn the anti-fall or protection signal act. Eliminate Anti-fall learning “0E” interference and press open fault button to clear the error and learn again.