Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
Barrier Gate User Manual YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
Page 4
Barrier Gate User Manual Regulatory information FCC information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 5
Barrier Gate User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which...
Page 6
Barrier Gate User Manual Keep the device away from magnetic interference. Avoid device installation on vibratory surface or places, and avoid equipment installation on vibratory surface or places subject to shock (ignorance may cause device damage). DO NOT touch the heat dissipation component to avoid burns.
Chapter 1 Introduction 1.1 Product Introduction Barrier gate is the entrance and exit management device to limit motor vehicle passing. It can control the boom pole automatically via parking lot management system. Or you can control the boom pole via buttons on remote controller.
Barrier Gate User Manual 1.2.3 Safety Feature Resistance rebound. If the boom pole is resistant during falling, it can rebound automatically. Induction anti-collision. When the boom pole is falling while the induction signal is received, the boom pole will rise automatically and keep rising during the triggering process. After the induction signal restores, the boom pole will fall automatically to guarantee safety.
Barrier Gate User Manual Figure 1-1 Boom Pole Direction 1.5 Safety Instruction Conform to the following instructions for your safety. DO NOT open the host door or cover when the device is working. The internal wiring of the device has been completed when leaving factory. In normal conditions, DO NOT change the wiring.
Chapter 2 Internal Structure 2.1 Internal Structure Overview The internal structure of the barrier gate host is run by the worm and gear transmission deceleration asynchronous motor. The movement is transmitted to the main shaft via four-bar linkage mechanism. The angle sensor can detect the rotation angle of the output shaft, and locate the position of the boom pole accurately.
Page 12
Barrier Gate User Manual Figure 2-2 Machine Core Structure There are extension springs installed inside the barrier gate host. During installation and debug, you can adjust the diameter and quantity of the springs according to the length of the boom pole to reach the moment balance.
Page 13
Barrier Gate User Manual boom pole/Curved 3 m ≤ L < 3.5 2 × φ 4.5 boom pole 3.5 m ≤ L ≤ 4 m 2 × φ 4.5 4 m < L < 2 × φ 5.5 5 m ≤ L ≤ 6 m 2 ×...
Refer to the figure below for the dimension of the barrier gate with non-telescopic straight boom pole. Figure 4-1 Dimension For the barrier gate with telescopic straight boom pole or curved boom pole, the dimensions of the host and base are the same as above.
Barrier Gate User Manual Chapter 5 Barrier Gate Component 5.1 Barrier Gate with Straight Boom Pole Refer to the figure and table below for the component description of the barrier gate with straight boom pole. Figure 5-1 Barrier Gate Component (1)
Hexagon check nut M8 Boom pole mounting housing label 5.2 Barrier Gate with Curved Boom Pole Refer to the figure and table below for the component description of the barrier gate with curved boom pole. Figure 5-2 Barrier Gate Component (2)
Page 18
Barrier Gate User Manual Table 5-2 Barrier Gate Component Description (2) No. Name Quantity Barrier gate host Boom pole Cross recessed pan head screw M3 × 8 1 Boom pole mounting housing Hexagon head bolt M8 × 65 Flat washer φ 8...
Make sure the base of the barrier gate host can be fixed firmly on the foundation, and the perpendicularity of the host to the horizontal plane is smaller than 1°.
4. Install peripheral devices. 1) After the barrier gate installation and debug completes, wire the lines in the host and connect the control lines of the peripheral devices according to the wiring diagram. 2) Debug the devices.
In auto learning mode, press the buttons to get the rising limit position, locate the falling limit position and judge the boom pole direction automatically, and calculate the running time of the barrier gate. When the status indicator is flashing in the frequency of 0.1 s, loosen the buttons.
S0: If it is on, during the rising of the boom pole, when the vehicle is passing through the induction loop while the barrier gate receives the rising signal again, the boom pole will not fall down after the vehicle passed through. It will fall down after the second vehicle passed through the induction loop.
Learning limit positions automatically must be done when you debug the main board for the first time, or when you change a new main board for the barrier gate. Or the barrier gate may run abnormally, and the main board will beep twice every one second. The beeping duration each time is 0.2 s, and the beeping interval is 0.2 s.
Page 24
Barrier Gate User Manual between the rising limit position (or falling limit position) and the mechanical limit position to ensure the motor can run for more than 0.3 s. In angle sensor mode, if exception occurs and the device needs to learn the limit positions...
Barrier Gate User Manual Chapter 8 Maintenance Clear the dirt on the barrier gate surface regularly to keep it clean. Check if the fasteners of the device are loose or lost once every month. Fasten them in time.