Table of Contents
Advertisement
Available languages
Available languages
Installing and Removing Attachments (Fig. C)
WARNING: Ensure LEDs are off and the system is not on.
Blender / Wine Opener / Can Opener / spice grinder
1. To install, slide the attachment head
onto the motor
6
and turn clockwise (as viewed from the
end of the attachment) until it securely locks in.
nOTE: The attachment can be installed on the motor in four
different locations, so it does not need to be placed in any
one specific orientation.
2. To remove, turn counterclockwise and pull attachment off.
Whisk / Frother
1. To install, slide the whisk pole
the adaptor hole
9
until it clicks into place and is secure.
2. Slide the adaptor
8
onto the motor
clockwise (as viewed from the end of the attachment)
until it locks in securely.
nOTE: The attachment can be installed on the motor in four
different locations, so it does not need to be placed in any
one specific orientation.
3. To remove, turn adaptor counterclockwise and pull it off,
then pull the whisk or frother from the adaptor.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and keep hands away from
the switch before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
On / Off (Fig. D)
iMPORTAnT: Never turn the motor on unless attachments
are securely attached.
nOTE: Optimal temperature for use is between 50–104 °F
(10–40 °C).
1. To turn unit on, either:
‑
Press unlock button
‑
Press power button, then press unlock button.
‑
Press unlock and power buttons simultaneously.
nOTE: There is a slight delay between pressing both buttons
and the appliance starting.
2. When the appliance is ready to use, the LEDs
illuminate and remain solid. If they do not, refer to the
TROUBLESHOOTING section.
nOTE: If LEDs go off during use, or don't light when starting
unit, release buttons and go back to step 1.
3. Once the unit is on, the buttons may be released for up to
5 seconds. The motor will stop running after the buttons
are released but the appliance remains active for 5 seconds.
As long as the power button is pressed at least once within
5 seconds after releasing, the appliance will turn back on.
4. To turn off, release both buttons. The appliance will
remain active for 5 seconds before turning off.
WARNING: The LEDs will stay on after buttons are
released. Ensure the LEDs are off and the unit has fully
stopped before removing attachments.
55
of the attachment
55
or frother pole
6
and turn
2
, then press power button
5
will
Speed Control (Fig. E)
The appliance has a variable‑speed dial
the appropriate speed for the attachment being used (1 is
the lowest speed, 5 is the highest speed).
ATTACHMENT
Immersion Blender
Wine Opener
Can Opener
Spice Grinder
Whisk
57
into
Frother
nOTE: With a 5‑second delay before the unit turns off, you
can release the buttons and use your thumb to adjust speed
without turning the unit off.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Hold the appliance
button
2
and use your thumb or a finger to push down the
power button
Storage Bins
The storage bins
or stacked vertically for convenient storage.
Stacking Storage (Fig. G)
1. Line up the bump
of the bottom bin.
2. Place the first bin on top of the second bin so it is engaged
with the stop ribs
lock together so tipping may dislodge the bins.
3
.
nOTE: It is not recommended to stack higher than two bins.
nOTE: Two small bins can be stored on top of a large bin.
Side‑by‑Side Storage (Fig. H)
1. Slide the storage bin connector
channel
22
2. Slide the channel of a second bin along the connector
until it clicks into place and is secure.
nOTE: It is not recommended to connect two large bins side
by side.
Charging in Storage Bin (Fig. I)
1. Place the charger connector
of the large bin
2. Run the charger cord
of the bin and out of the charging notch
3. Lay the unit in the bin so the charging pegs
unit fully engage with the charger connector.
SPEED
Start at 1, increase as needed
Start at 1, increase as needed
Start at 5, decrease as desired
1
so your palm presses down the unlock
3
.
16
and
17
can be connected horizontally
18
of the top bin with the recess
20
to prevent shifting. The bins will not
21
onto the storage bin
of one bin until it clicks into place and is secure.
14
into the connector detent
17
.
through the cord channel
13
English
4
. Turn the dial to
5
5
5
19
56
57
23
.
7
on the
13
Advertisement
Table of Contents
