Table of Contents
Advertisement
ENGLISH
Use your BLACK+DECKER charger only to charge the
u
battery in the appliance/tool with which it was supplied.
Other batteries could burst, causing personal injury and
damage.
Never attempt to charge non-rechargeable batteries.
u
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The charger must be placed in a well ventilated area when
u
charging.
Labels on the charger
The following symbols are found on your charger:
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Lock-off button
3. Oil cap
4. Front guard
5. Chain tension adjustment ring
6. Chain
7. Guide bar
8. Chain sheath
9. Chain adjust locking knob
10.Chain cover assembly
11. Oil level indicator
12. Battery
Assembly
Warning! Before assembly, remove the battery (12) from the
tool.
12
(Original instructions)
Fitting the guide bar and chain. (fig. A - L)
Always wear protective gloves when installing
or removing the saw chain (6). The saw chain is
sharp and can cut you when it is not running.
Place the chainsaw onto a stable surface (fig. A).
u
Fully loosen the chain adjust locking knob (9) (fig. B).
u
Remove the chain cover assembly (10) (fig. C).
u
Turn the tension adjust ring (5) anti-clockwise as far as it
u
will go so the arrow on the tension adjust ring (5) lines up
with the marker on the chain cover assembly (13) (fig. D).
Place the chain (6) over the guide bar (7) making sure that
u
the saw chain cutters on the upper part of the guide bar
(7) face towards the front (fig. E).
Guide the chain (6) around the guide bar (7) and pull it to
u
create a loop to one side at the rear end of the guide bar
(7).
Guide the chain (6) around the drive sprocket (14). Place
u
the guide bar (7) onto the bar location studs (15) (fig. F &
G).
Place the chain cover assembly (10) onto the chainsaw
u
(fig. H) making sure the arrows are aligned (fig. I).
Turn the chain adjust locking knob (9) clockwise to attach
u
the chain cover assembly (10) and lightly tighten (fig. I). to
release the tension (fig J).
Turn the chain adjust locking knob (9) 180 degrees
u
anticlockwise to release the tension (fig J).
Turn the chain tension adjust ring (5) clockwise until the
u
chain (6) is tight. Make sure that the chain (6) is snug
around the guide bar (7) (fig. K).
Check the tension as described below. Do not overtighten.
u
Tighten the chain adjust locking knob (9) (L).
u
Checking and adjusting the chain tension (fig. K)
Before use and after every 10 minutes of use, you must check
the chain tension.
Remove the battery (12).
u
Lightly pull on the chain (6) as shown (inset fig. K). The
u
tension is correct when the chain (6) snaps back after
being pulled 3 mm away from the guide bar (7). There
should be no "sag" between the guide bar (7) and the
chain (6) on the underside.
Note: Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the guide bar and
the chain.
Note: When the chain is new, check the tension frequently
(after disconnecting from the mains) during the first 2 hours of
use because a new chain stretches slightly.
To increase the tension (fig. J, K & L)
Turn the chain adjust locking knob (9) 180 degrees
u
anticlockwise to release the tension. (fig. J).
Advertisement
Table of Contents
