Honeywell LightSpot LS1000R Installation And Operating Instructions

WALK TESTING
1 2
MIN. SUN.
MANUAL OVERRIDE OPERATION
Activate Manual Override Operation
2 SEC
5
SEC
Lamp turn on
when reach Lux
OFF ON
setting level.
ON
2 times within 2 seconds
SWITCHABLE LOAD
Max 2000W @230V
Max 500W
Max 400W
TECHNICAL SPECIFICATIONS
Detection Range: Up to 6 metres diameter (3m Radius)
at mounting height of 2.5m
Detection Angle: 360°
Power Supply: 230Vac 50Hz
Maximum Switchable Load: Max load current 10A
Incandescent / Halogen Max 2000W
Fluorescent lamp (magnetic) Max 500W
Fluorescent lamp (electronic ballast) Max 400W
Low energy (CFL) Max 120W
LED lamp Max 400 W
Fan Max 75W
Time On Adjustment: 5 seconds - 15 minutes
Dusk Level Adjustment: Day & night or night only operation
Operating temperature: 0 to 40 degrees
Environment Protection: For ceiling mount - IP44
For flush mount - IP44 (at sensor portion only)
- IP20 (ceiling board onwards)
3
warm up
20-50 SEC
Around
10 second
Deactivate Manual Override Operation
1 Manual deactivation before dawn
1 SEC
DUSK
5
SEC
Hrs
DAWN OFF ON
ON
1 time within 1 second
OR
2 Auto deactivation when
Lamp turn off when
dusk to dawn dusk to dawn.
ON
Max 120W
Max
Max 75W
GUARANTEE
The company undertake to replace or repair, at its discretion should it become defective within a period
of 1 year after delivery, solely as a result of faulty materials and/or workmanship. Understandably, if
the product has not been installed, maintained or used appropriately, or if an attempt has been made to
rectify, dismantle or alter the product in any way, the guarantee will be invalidated.This guarantee states
the company's entire liability. It does not extend to cover consequential loss or damage or installation
cost arising from the defective product.This guarantee does not restrict or infringe the normal statuary
rights of the customer.
COMPLIANCE WITH E.U. DIRECTIVES
Apart from meeting the appropriate British standards, products are
manufactured in accordance with BS EN ISO 9002 and comply
with the LV (72/23/EEC) Directive.
At the end of their useful life the
packaging and product should
be disposed of via a suitable
recycling centre.
Do not dispose of with normal
household waste. Do not burn.
W6039 REVD 12/2/2023
LS 100 0R Lig
Only suitably qualified personnel should install this equipment
!!
•To prevent electrocution, do not work on any appliance live. Turn off mains before commencing work, lock-out tag-out must be followed.
•The current editions of the IEE Wiring Regulations (BS7671) and Buildings Regulations must be followed for installation.
•Ensure all terminal screws are fully tightened and product is securely fixed to its mounting box prior to turning on the mains supply.
PACK CONTENTS
x1
REQUIRED (Warning: Use only VDE Certified Tools)
Ф5mm
Auto Mode
x1
MOUNTING/ INSTALLATION STEPS
Surface Mount
1
Auto Mode
4
400W
7
9
EU contact for regulatory questions:
PEHA Elektro GmbH & Co.
KG Gartenstraße 49,
58511 Lüdenscheid Germany
Web: www.peha.de
Honeywell
St Marks Court, North Street
Horsham, West Sussex RH12 1BW
Tel: +44 (0)1942 719229
Web:www.buildings.honeywell.com/gb/e
n/brands/our-brands/ex-or
htSpot 360 ° Dual Mount PIR installation and operating instructions
x1 x1 x1
No 2
Phillips
4mm
3mm
x1 x1
2
5
8
N
Cable entry
capability at
terminal block
1 x 2.5mm²
2 x 1.0mm²
2 x 1.5mm²
OR
Remark: R terminals are Volt-Free output
(when link is removed)
OR
'CLICK'
'CLICK'
M3 x 20mm M3 x 15mm
M4 x 14mm
(For ceiling mout (For cable clamps
(For Euro conduit box
installation) installation)
installation)
x2 x4 x2 x2
x2
Hole saw size:
Ф75mm - 80mm
x1 x1 x1
3
0FF
6
CAUTION:
Option1 (live out) Option2 (volt-free)
L R R
L Live Brown L Live Brown
N Neutral Blue N Neutral Blue
Earth Green / Yellow Earth Green / Yellow
R R
Switched Live Brown Volt-Free
Brown
R Relay contact
Load
N L R R
N L R R
µ
µ
N
L
N
L
R
R
Note: Remove the external link
'CLICK'
The device needs
20-50 seconds to
warm up.
Cut out
here