Table of Contents
Advertisement
Quick Links
MANUALE
USER
USER
USER
USER
USER
MANUAL
INSTRUKCJA
MANUEL DE
USER
USER
USER
USER
USER
USER
USER
USER
UŽIVATELSKÝ
BENUTZERHANDBUCH
GEBRUIKERSHANDLEIDING
MANUAL
MANUAL
DE USUARIO
UTENTE
L'UTILISATEUR
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
MANUAL
UŻYTKOWNIKA
MANUÁL
Honeywell BW ™ Icon & BW ™ Icon +
Přenosný vícenásobný detektor plynu
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Draagbare meervoudige gasdetector
Detector de gases múltiples portátil
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Tragbarer Mehrfachgasdetektor
Portable Multiple Gas Detector
Détecteur de gaz multiple portable
Portable Multiple Gas Detector
Rilevatore di gas multiplo portatile
Portable Multiple Gas Detector
Przenośny detektor wielu gazów
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Portable Multiple Gas Detector
Shop for Gas products online at:
CanarySense
www.
M05 4002 002 EN A ©2020
.com
1.888.610.7664
Advertisement
Table of Contents
Related Manuals for Honeywell BW Icon
Summary of Contents for Honeywell BW Icon
- Page 1 MANUAL MANUAL MANUAL MANUAL MANUAL UŻYTKOWNIKA MANUÁL Honeywell BW ™ Icon & BW ™ Icon + Portable Multiple Gas Detector Tragbarer Mehrfachgasdetektor Détecteur de gaz multiple portable Rilevatore di gas multiplo portatile Przenośny detektor wielu gazów Přenosný vícenásobný detektor plynu Draagbare meervoudige gasdetector Detector de gases múltiples portátil...
-
Page 2: Table Of Contents
Charge the Battery Firmware Update Additional Information Sensor Poisons and Contaminants Sensor Specifications General Specifications Time Out Events Troubleshooting DataLogs and Event Logs Alarms Replacement Parts Security Information BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:... -
Page 3: Introduction
Learn what you need to know about the Honeywell BW™ Icon Gas Detector before operating. Product Description The Honeywell BW™ Icon & Honeywell BW™ Icon+ gas detectors warns of hazardous gas at levels above user-defined alarm setpoints. The detector can monitor up to four gases at a time. - Page 4 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. BW Icon User Manual CanarySense www.
-
Page 5: What's In The Box
What's in the Box Honeywell BW™ Icon gas detector Battery (factory-installed) USB charger Calibration cap Klick Fast stud Quick Reference Guide Tubing Overview LED Alarm Sensor IntelliFlash Clip Display Battery Button Charging Port Beeper BW Icon User Manual CanarySense www. - Page 6 Calibration — Shows when calibration is due and you can configure to have a count down. Battery status — Shows battery status and when on charge will show charging status. Bluetooth — All devices have Bluetooth – double click to enter menu. for search mode BW Icon User Manual CanarySense www. .com 1.888.610.7664...
-
Page 7: Operations
CHAPTER Operations Learn what you can do with your Honeywell BW™ Icon Detector, from commissioning to Calibration. Activate the Detector To turn the detector on, press, and hold the button for four seconds. LEDs light and the instrument vibrates and beeps. -
Page 8: Common Button Operations
1-second hold Bluetooth Pairing The user can pair the Honeywell BW™ Icon to a mobile device via built-in Bluetooth Low Energy (BLE). The Honeywell Device Configurator app, installed on the mobile device, can then show gas readings and alarms from the BW Icon unit that is connected. -
Page 9: Calibration
• Apply gas from a cylinder to the sensors using the Safety Suite Device Configurator (SSDC) software or the Device Configurator (DC) app. • Use an IntelliDoX module. For further reference see the IntelliDox User Manual. BW Icon User Manual CanarySense www. - Page 10 Procedure to calibrate the detector via the calibration cap and the DC app on a mobile device 1. Turn On the BW Icon. Place the cap over the detector, and then press down on both tabs to snap it into place. Wait a few minutes to sensors warm up.
- Page 11 Single press until the BLE icon is displayed. Hold press 3 secs to initiate the pairing mode. 5. In the Device list screen from the Device Configurator app, select the BW Icon Serial Number to start pairing. 6. In your Mobile device, tap on the Menu button and then select Remote Calibration 7.
- Page 12 9. After the Zero calibration is completed, use any of the following three ways to select the gas cylinder, and then click START. 10. Select the sensor that you want to calibrate and then tap START. BW Icon User Manual CanarySense www.
- Page 13 11. Open the cylinder valve by turning the pressure regulator knob counterclockwise. Follow onscreen instructions to know when to apply gas. The IntelliFlash lights amber. BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
- Page 14 The detector will start purge, and the slots LEDs will flash in yellow clockwise. After purge is completed, the instrument will back to the regular mode. BW Icon User Manual CanarySense www.
- Page 15 Calibrate the BW Icon via the Safety Suite Device Configurator (SSDC). 1. Turn On the BW Icon. Place the cap over the detector, and then press down on both tabs to snap it into place. Wait a few minutes to sensors warm up.
- Page 16 LEDs are solid green if calibration passed, or red if failed. 10. Remove the calibration cap. The detector starts purging, and the slots LEDs flash in yellow clockwise. After the purge is complete, the device is back to the regular mode. BW Icon User Manual CanarySense www.
-
Page 17: Bump Test
Apply gas from a cylinder to the sensors manually through the calibration cap, and using the detector's menu. 1. Turn On the BW Icon. Place the cap over the detector, and then press down on both tabs to snap it into place. Wait a few minutes to sensors warm up. - Page 18 LEDs are solid green if calibration passed, or red if failed. 6. Remove the calibration cap; the detector starts purging, and the slots LEDs flash in yellow clockwise. After the purge is complete, the device is back to the regular mode. BW Icon User Manual CanarySense www.
- Page 19 Safety Suite Device Configurator (SSDC) software on a personal computer (PC). 1. Turn On the BW Icon. Place the cap over the detector, and then press down on both tabs to snap it into place. Wait a few minutes to sensors warm up.
- Page 20 LEDs are solid green if calibration passed, or red if failed. 10. Remove the calibration cap. The detector starts purging, and the slots LEDs flash in yellow clockwise. After the purge is complete, the device is back to the regular mode. BW Icon User Manual CanarySense www.
- Page 21 Apply gas from a cylinder to the sensors manually through the calibration cap, and using the Device Configurator (DC) app on a mobile device. Turn On the BW Icon. Place the cap over the detector, and then press down on both tabs to snap it into place. Wait a few minutes to sensors warm up.
- Page 22 Single press until the BLE icon is displayed Hold press 3 secs to initiate the pairing mode. In the Device list screen from the Device Configurator app, select the BW Icon Serial Number to start pairing. In your Mobile device, tap on the Menu button and then select Bump Test.
-
Page 23: Zero Calibration
4. Tap Measurements 5. Tap Start Recording. Set the Detector via Device Configurator 1. Pair the BW Icon with the Device Configurator App on your mobile device. 2. Tap the menu button 3. Tap Device Setup 4. Tap Download, to get the configuration table. -
Page 24: Maintenance
If the device is out of charging range, the battery icon flashes blue. Charge the battery using Honeywell charger adapters designed for this apparatus only. Do not use any other charger adapters. Failure to adhere to this caution can lead to fire and explosion. - Page 25 Fully charged 100% The Battery icon lights in solid green, and one short beep. When the Temperature: >45 °C, <0°C. Can't charge The battery icon flashes twice per second. BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
- Page 26 The detector can be activated during charging. After charge is complete, the battery icon flashes green. Remove the detector. Note: For further information, refer to the Multi-Unit Cradle Charger User Manual. BW Icon User Manual CanarySense www. .com 1.888.610.7664...
-
Page 27: Firmware Update
1. Open the Device Configurator app on your mobile phone. 2. Tap Menu 3. Tap Firmware 4. Tap Update 5. Tap YES to implement the Firmware update, and wait until Update Successfully is displayed. 6. Tap OK. BW Icon User Manual CanarySense www. .com 1.888.610.7664... -
Page 28: Additional Information
CHAPTER Additional Information Learn from about strategic information related to the Honeywell BW™ Icon Detector. Sensor Poisons and Contaminants Several cleaners, solvents, and lubricants can contaminate and cause permanent damage to sensors. Cleaners and Lubric- Silicones Aerosols ants Bug repellents and... -
Page 29: Sensor Specifications
Sensor Specifications Gas Type Measuring Range Resolution 0~2000 ppm 1 ppm 0~200 ppm 0.1 ppm 0~30% VOL 0.1% VOL NDIR-CH4 0~100% LEL 1% LEL 0~150 ppm 0.1 ppm Measuring Unit New Sensor Warm Up Time Working Temperature ppm, mg/m3, umol/mol 0.5h -40°C to +60°C ppm, mg/m3, umol/mol... - Page 30 Sensor Specifications Default SPAN Value Default SPAN Value Type Type 18.0% 18.0% NDIR- NDIR- SPAN Value Range Type 35~500 10~100 0~25% NDIR- 10~100% 10~100 Calibration Flow Rate Type 500ml/min 500ml/min 500ml/min NDIR- 500ml/min 500ml/min CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
- Page 31 Sensor Specifications CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
-
Page 32: General Specifications
General Specifications BW Icon BW Icon + 108.2mm x 61.5mm x 43.2mm(4.29" x 2.44" x1.7 ") with Alligator Clip 108.2mm x Size 61.5mm x 37.8 mm(4.29" x 2.44" x 1.49") with Klick Fast Stud Weight 185g with Alligator Clip,169g with Klick Fast Stud... -
Page 33: Time Out Events
The detector, side LEDs, and IntelliFlash light for 5 Temperature sensor fail Replace PCBA seconds, and sound one long beep and two short BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:... - Page 34 Stop data communication via Apparatus is in DC mode. a mobile phone. Apparatus is in IR Stop data communication via communication. IR Link. BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
- Page 35 Battery is depleted. light after charging, contact display when charging. Battery is out of required Battery icon flashes in Move to 0~45°C ambient charging temperature blue. temperature. range. BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
-
Page 36: Datalogs And Event Logs
3: Gas stel 4: Gas twa 5: Gas over range 6: Gas negative 7: Sensor failure 8: Multi alarm 9: Zeroing 10: Spanning 11: Bumping 12: Disabled BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:... -
Page 37: Alarms
Beeps and vibrates. Alarm 2 icon lights red and flash once every second. Left and High Right alarm LEDs flash every second. Alarmed sensor LED flashes twice every second. Beeps and vibrates. BW Icon User Manual CanarySense www. .com 1.888.610.7664... - Page 38 Setpoint Silence when transmitting data to Negative Keep alarm until reading increase <-5%LEL Safety Suite Device Alarm above or equal to -5%LEL Configurator or Device Configurator BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:...
-
Page 39: Replacement Parts
Range ting range Range NDIR- 1% LEL 5~60% 5~60% Replacement Parts CP-SS-K1 Sensor membrane (kit of 20) CP-LBL-1 Sensor name plate Accessories: M05-2011-000 Calibration cap BW Icon User Manual CanarySense www. .com 1.888.610.7664 Shop for Gas products online at:... -
Page 40: Security Information
Cybersecurity Framework and NIST Alerts, InfraGard Alerts, and the United States Computer Emergency Readiness Team (“US-CERT”) Alerts and Bulletins, and their equivalents. The software is provided “as is” without any express or implied warranties. Honeywell, its affiliated companies, and licensors expressly disclaim any implied warranty of merchantability, warranty of fitness for a particular purpose, and warranty of non-infringement. - Page 41 Honeywell, its affiliates, and licensors liable for any loss of data, loss of profit, or any loss or damage, whether direct, indirect, incidental, special, or consequential, however arising, as a result of accessing or using the software. So long as this provision is enforceable in Customer’s jurisdiction, the foregoing limitations, exclusions, and disclaimers apply to the fullest extent permitted by law even if any remedy fails of its essential purpose.
- Page 42 The measuring range of the combustible gas sensor is 0~100%LEL, it is recommended to do calibration if the readings are not within specified limits. If necessary, read IEC 60079-29-2 for a special calibration procedure. BW Icon User Manual CanarySense www.