Food Chopper; Blending; Attaching And Removing Blender Guard - Black & Decker BCKM101 Instruction Manual

English

WARNING: Ensure the immersion blender attachment
head is assembled to the motor as detailed in the
Installing and Removing Attachments section.
nOTE: Do not use the immersion blender
cookware as it may scratch or mark nonstick coatings.
Blending (Fig. J)
1. Place food to be processed in mixing cup
container should only be 1⁄2 full or less when blending
liquids or when making a puree of fruit and/or
vegetables to prevent food from overflowing.
2. Immerse the blender head
the mixing cup.
3. Set the variable‑speed dial
by turning the dial. This will help avoid splattering and
overprocessing.
4. Turn the unit on as described in the On/Off section.
5. Blend the ingredients by moving the appliance up and
down and in circles. Do not pull immersion blender head
out of food.
iMPORTAnT: The continuous operating time must be less
than 30 seconds. Never blend hot oil, fat, or meat.
6. After you have completed blending, release the unlock
button 2 and power button
7. If the immersion blender blade
‑ Turn unit off while keeping the blender
head submerged,
‑ Allow the blade to stop,
‑ Wait until the LEDs
Lift the blender out of the container,
‑
‑ Disassemble the blender from the motor by turning
the attachment counterclockwise,
Remove blockage,
‑
‑ Securely reattach the blender.
nOTE: Do not pull blender out quickly. Blending creates
suction at the bottom of the cup, which can cause contents
to splatter.
8. Keep blender attachment inside the mixing cup to
prevent dripping on counter.
9. After processing, disassemble the immersion blender from
the motor by turning the attachment counterclockwise.
10. Clean the attachment as needed. For more information,
refer to Cleaning section.
Immersion Blender Tips and Tricks
• The immersion blender blends foods and liquids
rapidly, therefore, it is easy to overprocess. Stop the
motor and check food throughout the operation to
avoid overprocessing.
• When pureeing and blending, cut food into uniform
sizes. This will ensure smooth and consistent results.
• Allow hot food to cool slightly before blending.
12
14 with non‑stick
8 . The
15 as deeply as possible into
4 to 1 and increase speed
3 to stop the motor
16 becomes blocked:
5 turn off,

Attaching and Removing Blender Guard

(Fig. K)

CAUTION: Do not attach or remove immersion blender
guard
is installed to the motor. Avoid contact with the blade
while attaching and removing the blender guard.
1. To attach the blender guard, align the immersion blender
guard detents
on the immersion blender attachment. Slide the blender
guard onto the immersion blender attachment. Ensure
the guard clicks firmly into the detents.
2. To remove, depress the detents and slide the guard off.
3. Clean the blender guard as needed. For more
information, refer to Cleaning section.
Intended Use
6 . This food chopper is intended for residential use only.
It can be used for chopping, dicing, pureeing and mincing
tomatoes, onions, garlic, crackers, ginger, and for grinding meat.
DO nOT let children come into contact with the appliance.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and keep away from the
power button before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.

WARNING: Do not touch blade. It is sharp and may
cause serious injury.

WARNING: Ensure the food chopper attachment head
is assembled to the motor as detailed in the Installing
and Removing Attachments section.
Using the Food Chopper (Fig. L - O)
1. Place the food chopper cylinder
nOTE: The ring around the bottom of the cylinder will help
keep it from sliding while in use.
2. Remove blade guards
3. Slide the blade shaft
shown in Fig. M.
4. Add ingredients to the cylinder. Do not fill past the top
measurement line
5. Place the food chopper lid
clockwise until it securely locks as shown in Fig. N. You
will feel the blade shaft and lid click into place.
6. Ensure the liquid port cover
port 22 . The cover should always be in place while using
the food chopper, except when adding liquid ingredients.
7. Attach the motor
AND REMOVING ATTACHMENTS section.
18 while the immersion blender attachment
19 with the immersion blender slots

FOOD CHOPPER

BCKM101FP
24
27 before use as shown in Fig. L.
28 onto the cylinder nub
29 marked "Max. "
21 on the cylinder and twist
23 is seated in the liquid
6 as described in the INSTALLING
17
on a flat surface.
25 as