Table of Contents
Advertisement
Quick Links
1. Installation
Installation Standard
Choose a horizontal installation floor
Pre-embedded cables, the conduit should be 50 mm above the ground to prevent
water from entering the cable and causing a short circuit
When installing against a wall, at least 200mm of space should be reserved between
the back cover and the wall to facilitate wiring and other operations
When installing this device, the fuselage needs to be turned sideways to align with
the capture position;
(1) Capture Distance
The capture position is 3.5-5m away from the capture unit
2. Fixed Base
The camera needs to be fixed to the mounting surface with expansion screws.
(1) According to the general direction of the all-in-one chassis on the safety island,
punch 3 holes in the safety island, as shown in the figure below
How to Configure DS-TMC403-E
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-TMC403-E
Summary of Contents for HIKVISION DS-TMC403-E
- Page 1 How to Configure DS-TMC403-E 1. Installation Installation Standard Choose a horizontal installation floor Pre-embedded cables, the conduit should be 50 mm above the ground to prevent water from entering the cable and causing a short circuit When installing against a wall, at least 200mm of space should be reserved between the back cover and the wall to facilitate wiring and other operations ...
-
Page 2: Cable Connection
(2) Use an impact drill to drill holes on the installation holes with a depth of about 120mm; for the 3 racetrack holes at the bottom (3) Insert the expansion bolts with a diameter of 12mm into the installation holes, and tighten the nuts to fix them. - Page 3 IO trigger: the trigger device is connected to IN1 and G of the ALARM port; (2) Gate control and gate signal wiring: Control gate: the corresponding 1A1B2A2B corresponding to the opening and closing of the gate The wiring of the remote control alarm signal of the gate: the output of the gate is opened in place (remote control alarm) and connected to the camera ALARM IN1, After the gate signal wiring is completed, you need to configure the relevant functions Configuration - Entrances and Exits - Entrance and Exit - Barrier...
-
Page 4: Application Mode
restart, simply restore and then restart, and then re-configure. 5. Application Mode (1) Trigger type I/O coil: trigger camera capture by external switch signal, coil or radar Video Detection: trigger camera capture through pure video Radar mixed operation: select this triggering method for radar mixed operation (2) I/O Trigger Default Status ... -
Page 5: Angle Adjustment
6. Angle adjustment The optimal recognition effect requires the license plate to be placed in the lower 1/3 of the center of the image, as shown in the following figure Adjust the camera orientation by rotating the fuselage left and right, and adjust the internal up and down by adjusting the screws as shown in the figure. - Page 7 7. Pixel adjustment (1) License plate recognition position and pixel points The trigger recognition range of the capture camera is 3.5-5 meters, and the best position is 4 meters (the distance between the trigger capture and the camera); the capture position of the capture camera is best at the lower 1/3 of the overall image;...
- Page 8 8. Recognition Area The identification area must be drawn according to the actual scene of the scene, and it is forbidden to use the default area or doodle randomly. When taking pictures, the license plate and the front of the car must be inside the recognition area.
-
Page 9: Capture Parameters
The quadrilateral formed by lane line 1 and the right boundary line of the lane is the detection area Trigger line: In coil mode, the trigger line is configured as the actual trigger position and inside the quadrilateral surrounded by lane lines; in video trigger mode, the trigger line is set at half of the quadrilateral formed by the lane lines, and is guaranteed to be within the quadrilateral 9. -
Page 10: Image Parameters
10. Image Parameters (1) General parameters WDR: If the lights are too bright at night and the image is too explosive, the WDR can be turned on to suppress the lights according to the time. Note: Turning on WDR will cause the image noise to increase, so you don't need to turn it on when it's not necessary ... - Page 11 Gain: If the image is too explosive at night, the gain can be appropriately reduced 11. Entrances and Exits Control mode: The platform control corresponding to the opening signal is sent by the platform; the camera control is controlled by the camera according to the vehicle information management to determine the opening of the gate itself ...
- Page 12 Remote Control Barrier Gate: You can check whether the line connection between the camera and the barrier is normal through this function...