Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-KB6003-WIP
Summary of Contents for HIKVISION DS-KB6003-WIP
- Page 1 Wi-Fi Video Doorbell User Manual UD06661B...
-
Page 2: User Manual
Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. -
Page 3: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 4 Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. Available Models This manual is applicable to the Wi-Fi Video Doorbell: DS-KB6003-WIP. Symbol Conventions The symbols that may be found in this document are defined as follows.
- Page 5 All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. ...
- Page 6 Make sure the power voltage across the doorbell should be between 16 VAC and 24 VAC. The power supply must conform to LPS. The recommended adaptor models and manufacturers are shown as below. Use the attached adapter, and do not change the adaptor randomly.
- Page 7 Doorbell Appearance Front and Rear Panels You can see the camera, call button, and crews for wiring on the doorbell on the front panel and the rear panel. Figure 1-1 Front Panel and Rear Panel Table 1-1 Components Description Name Description Auto light source for night vision.
- Page 8 Figure 1-2 Side Panel and Bottom Panel Table 1-2 Components Description Name Description For TF card. If a TF card is used, video files will be stored in the TF TF Card Slot card. If the doorbell has not been activated, hold the button for 5 seconds to enter the Wi-Fi connection mode.
- Page 9 Doorbell Installation 2.1 Attach Mounting Template Mounting template is included in the box content, and it is an auxiliary help for you to install the doorbell. Steps 1. Determine the installation height of doorbell. Figure 2-1 Suggested Installation Height 2. Align the cable hole on the mounting template with the cable hole on the wall. 3.
- Page 10 2.2 Connect Power Cables Before You Start Make sure you have powered off the main power switch of your home. Connect a resistor (included in the box content) to the doorbell if no electrical chime or mechanical chime is connected. Steps 1.
- Page 11 2.3 Install TF Card (Optional) You can use TF card to store the video files. Steps 1. Remove the faceplate attached on the doorbell to view the front panel and side panel of the doorbell. 2. Remove the card slot cover. 3.
- Page 12 Figure 2-6 Insert Expansion Tube 2. Route the cables and insert cables and power connector into the drilled cable hole. 3. Align the screw holes on the doorbell body with drilled holes on the wall. 4. Fix the doorbell body to the wall tightly with 2 screws. Figure 2-7 Install Doorbell 5.
-
Page 13: Getting Started
Getting Started Getting Started section provides the quick usage guide to the doorbell and its related application. 3.1 Set up Hik-Connect App Hik-Connect App is necessary for the doorbell configuration and operation. Before You Start Make sure your mobile device has been connected to Wi-Fi. Steps 1. - Page 14 1. In the Home page of the App, tap More -> Settings -> Wi-Fi Settings to enter the Wi-Fi settings page. 2. Input the wireless network name and password that your mobile phone has connected to. 3. Tap Generate to generate a QR code. 4.
- Page 15 The suggested scanning distance is 5 to 10 cm. The doorbell gives a beep for success. 3. Activate the doorbell. 1) Tap Set Device Password and input a password to activate the doorbell. 2) Tap Activate in the next page to finish activating. 4.
- Page 16 Activation page pops up after finishing the Wi-Fi connection. 4. Activate the doorbell. 1) Tap Set Device Password and input a password to activate the doorbell. 2) Tap Activate in the next page to finish activating. 5. Optional: Input the verification code of the doorbell in the pop-up page after activation.
- Page 17 Doorbell Operation Via the Hik-Connect App, you can realize some certain functions of the doorbell (including, but not limited to, live view, and remote playback). Video Intercom Press Call Button on the doorbell. You can accept the call via the Hik-Connect App, get the live view of the doorbell, and capture the snapshots.