Technical Specifications - GE ATS1203 Installation Sheet

Menu 1, DGP status
This menu lists different types of information regarding settings,
DGP addresses to poll, inputs ranges, output ranges, current
consumption, etc. To view all data, enter the menu and press
ENTER to view the next item.
Menu 2, Input status
Shows the current status of all inputs that have been enabled and
the digital value of the status. The range that is available can be
viewed in the DGP Status. The input numbers used are related to
the address selected. See "Zone and output numbering".
To view the status, enter the first input to view. The selected input
status is shown. Press MENU to view the previous or ENTER to view
the next input.
Menu 3, DGP settings
Menu 3 provides for some additional settings related directly to
the DGP functionality. Use the MENU key to change the settings.
Use ENTER to accept the settings and move to the next item.
1. DGP configuration: selects the number of inputs and outputs
used. Available settings:
1 DGP Address Allows for max 16 inputs/outputs to be connected.
Shows as "DGP: n" where n is the selected DGP
address in menu 1, DGP status (Default setting)
1 DGP+exp Allows for max 32 inputs/16 outputs to be
connected. Shows as "DGP: n + exp" where n is the
selected DGP address in menu 1, DGP status.
2 DGP Addresses Allows for max 32 inputs/outputs to be connected
but requires DGP polling to be enabled for the DGP
address and the DGP address + 1. Shows as "DGP: n
+ m" where n is the selected DGP address and m is
the address + 1 in menu 1, DGP status.
2. Battery load: Select if the battery load resistor should be
enabled on output 8. It will follow the battery test and add an
additional 68 Ω during the test. This option is required for
regulations (SKAFOR). Default is OFF.
3. Mains check: Enable/disable mains check. Set to OFF in case no
mains power supply is used to avoid mains fail being reported.
Default is ON.
4. Static outputs: Select whether to support static outputs (max 8)
or clocked outputs (max 32, depending on DGP configuration).
Default is Static outputs.
Menu 4, Factory reset
Use this menu to set all DGP configurations to default factory
settings.

Technical specifications

Mains power specifications
Mains Input Voltage (J17 – AC)
Current consumption at 230V~
Main board supply voltage
Power supply specifications
Power supply voltage
Power supply current
Auxiliary Power output* (J14)
P/N 1064130 • REV 3.0 • ISS 10MAR09
230 VAC ± 10%, 50Hz ± 10%
360 mA
23 VAC typical
13.8 VDC ± 5%
2.9 A max. at 13.8 VDC ± 5%
13.8 VDC ±5%
For current see table below
Battery Power output (J17 – BAT)
Battery Type and max. capacity
Main board consumption
* Maximum permanent current to power devices external to the control
equipment in the absence of alarm conditions.
Available Aux/Battery current based on backup
Time (h)
Incert 24 24 Aux
Battery
EN 1&2 12 72 Aux
Battery
EN 3&4 60 24 Aux
Battery
NF & A2P 36 30 Aux
ΙΙ
Battery
NF & A2P 72 30 Aux
ΙΙΙ
Battery
VdS 30 24 Aux
B Battery
VdS 60 24 Aux
C Battery
General feature specifications
End of line resistor 4.7 kΩ 5% 0.25 W (2.2 kΩ or 10 kΩ)
(standard)
Standard on board output Ext. siren (J13 — S+/S−)
Electronic output
Rating: 1 A at 13.8 VDC
Housing dimensions ATS1203: 370 x 475 x 160 mm
ATS1204: 460 x 475 x 160 mm
Colour Beige
Operating temperature −10 to +55°C (certified +5 to 40°C)
Humidity 95% noncondensing
IP protection grade IP30
Fuses
F4 Auxiliary power & F2 A, 20x5
siren
F5 Battery F3 A, 20x5
* Mains fuse ATS1203: Slow T – 400 mA 20x5
ATS1203N/ATS1204(N): Fast F– 630 mA 20x5
* Mains fuse is part of the mains terminal block.
WARNING: Before removing the mains fuse, mains power must be
disconnected!
13.8 VDC ± 5%.
For current see table below
Lead acid rechargeable 2 x 25 Ah
12 V nom. (BS129)
75 mA at 13.8 VDC ± 5%
Battery capacity (Ah)
7.2 18 25 36
Current (mA)
200 600 875 1200
2525 2125 1850 1525
490 1300 1800 1800
2235 1425 925 925
40 220 330 500
2685 2500 2395 2225
110 360 550 850
2615 2350 2200 1875
20 150 230 380
2700 2600 2500 2345
150 500 700 1050
2575 2225 2025 1675
40 220 330 500
2685 2500 2395 2225
50
1200
1525
1800
925
550
2175
1000
1725
580
2100
1100
1625
550
2175
7 of 24