Operation; Adjusting The Working Position - Makita UR101C Instruction Manual

1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2.
Place the nylon cutting head onto the spindle and
tighten it securely by hand.
3. Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Manual feed type
► Fig.25: 1. Nut 2. Nylon cutting head 3. Spindle
4. Hex wrench
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the nylon cutting head onto the spindle and
tighten the nut securely by the box wrench.
► Fig.26: 1. Box wrench 2. Hex wrench 3. Loosen
4. Tighten
3. Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Plastic blade
NOTICE:
Be sure to use genuine Makita plastic
blade.
► Fig.27: 1. Plastic blade 2. Spindle 3. Hex wrench
4. Loosen 5. Tighten
1.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the plastic blade onto the spindle and
tighten it securely by hand.
3. Remove the hex wrench from the gear case.
To remove the plastic blade, follow the installation pro-
cedures in reverse.

OPERATION

Adjusting the working position

CAUTION:
Before performing this procedure,
install the battery cartridge(s) to the portable
power pack and finish the adjustments for the
waist belt and shoulder harness. Refer to the
instruction manual of the portable power pack for
detail.
CAUTION:
To prevent unintentional start up,
never turn on the portable power pack throughout
this procedure. The battery cartridge(s) is to be
installed only to obtain the usability with actual weight
balance.
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, use the hanging band
included in the tool package or the hanging band
recommended by Makita.
If you put on the shoulder harness not recommended
by Makita and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is difficult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.
1. Pull out the cord from the right side of the portable
power pack. When pulling out the cord, be sure to set
the cord in the holders as shown in the figure.
► Fig.28: 1. Cord 2. Holder
2. Attach the hooks of the hanging band to the rings
of the shoulder belts or waist harness as shown in the
figure.
Attaching hanging band to the shoulder belt
► Fig.29: 1. Hanging band 2. Ring 3. Hook
Attaching hanging band to the shoulder belt and
waist belt
► Fig.30: 1. Hanging band 2. Ring 3. Hook
3. Wear the shoulder harness of the portable power
pack and lock the buckle on the waist belt.
► Fig.31
Adjust the length of the hanging band as necessary.
► Fig.32
4. Attach the tool to the shoulder harness using
the hook on the hanging band. Be sure to hook on the
hanger of the tool.
UR101C
► Fig.33: 1. Hook 2. Hanger
UR201C
► Fig.34: 1. Hook 2. Hanger
5. Insert the plug of the tool into the socket of the
portable power pack.
When inserting, align the triangle marking on both the
plug and the socket.
25 ENGLISH