Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita MR007GZ
Summary of Contents for Makita MR007GZ
- Page 1 Job Site Radio MR007G INSTRUCTION MANUAL IMPORTANT: Read Before Using.
- Page 2 7 8 9 10...
- Page 4 ENGLISH SYMBOLS (Original instructions) The following show the symbols used for the equipment. Be sure that you understand their meaning before use. EXPLANATION OF GENERAL Read instruction manual. VIEW (Fig. 1) Only for EU countries 1. Handle/Built-in antenna (DAB/FM) Due to the presence of hazardous 2.
-
Page 5: Important Safety Instructions
14. The MAINS plug is used as the disconnect device, IMPORTANT SAFETY and it shall remain readily operable. INSTRUCTIONS 15. Do not use the product at a high volume for any extended period. To avoid hearing damage, use the WARNING: product at moderate volume level. - Page 6 ● Danger of explosion if battery is incorrectly replaced. ● Replace only with the same or equivalent type. ● Only use genuine Makita batteries. Use of non- genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage.
-
Page 7: Operating Time
OPERATING TIME * The suitable battery packs for this radio listed as the following table. * The following table indicates the operating time on a single charge. AT SPEAKERS OUTPUT Battery cartridge voltage = 100mW Unit: Hour (Approximately) Battery capacity LXT (18V) Radio/AUX Bluetooth play... -
Page 8: Installation And Power Supply
● XGT/LXT battery cartridge INSTALLATION AND POWER Indicator or lamps SUPPLY Remaining capacity CAUTION: Lighted Blinking ● Be careful not to pinch your fingers when opening and closing the battery cover. 75% ~ 100% ● Return the battery compartment locker to the original position, after installing or removing 50% ~ 75% battery cartridge. -
Page 9: Listening To The Radio
● Use the AC power adapter supplied with the product or The DAB antenna is built into the handle. When operating specified by Makita only. the radio, please straighten the handle properly above the ● Do not hold the power supply cable and plug by your radio to get better reception. -
Page 10: Finding New Stations - Dab
setting. g. Date Displays the current date. 4. Press the Tuning Control knob to confirm the setting. If a DAB broadcast provides a slideshow image, this may Station order setup – DAB be viewed full-screen by pressing and holding the Tuning Control knob. -
Page 11: Miscellaneous Settings
4. Rotate the Tuning control knob to find your desired 2. Press the Advanced setting button to enter the menu station. setting. 5. To adjust the volume, press the Tuning control knob 3. Rotate the Tuning control knob to select “Audio again to switch to the volume control mode. -
Page 12: Language Options
Format”. Press the Tuning control knob to enter the information on how to update your radio can be found at setting. Makita website. 4. Rotate the Tuning control knob to select “DD-MM- 1. Using the micro USB cable (not supplied) to connect YYYY”... -
Page 13: Equalizer Function
can recognize each other. Equalizer function Note: There are 7 kinds of color LED indicators around the ● To have the better sound quality, we recommend Tuning control knob to indicate different EQ modes. setting the volume to more than two-thirds level on your 1. -
Page 14: Auxiliary Input Socket
● Bluetooth connectivity performance may vary AUXILIARY INPUT SOCKET depending on the connected Bluetooth devices. Please refer to the Bluetooth capabilities of your device A 3.5mm Auxiliary input socket is provided at the front before connecting to the radio. All features may not be of your radio to permit an audio signal to be fed into the supported on some paired Bluetooth devices. -
Page 15: Specifications
SPECIFICATIONS Power requirements DC 12V 2.5A, AC power adapter center pin positive Battery Slide battery: 10.8V - 36V FM 87.50-108 MHz (0.05MHz/step) Frequency coverage DAB/DAB+ 174.928-239.200 MHz DAB/DAB+ Channel block DAB (Band III) 5A-13F Compatible standard DAB/DAB+ ® Bluetooth ® (The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.) - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan MR007G-ENEU-2012 www.makita.com 3A81e25Z10000...