Makita DML805 Instruction Manual page 5

ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off, unplugged,
and the battery cartridge is removed before carrying out
any work on the tool.
Assembling the frame and the base (Fig. 1)
Assemble the worklight as follows:
1. Remove the screws.
2. Insert the legs of the frame into the base.
3. Align the holes of the frame and the base.
4. Tighten them with screws.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off, unplugged,
and the battery cartridge is removed before adjusting or
checking function on the tool.
Use with battery:
Installing or removing battery cartridge
CAUTION:
• Always switch off the tool and unplug before installing or
removing of the battery cartridge.
• Hold the tool and the battery cartridge firmly when
installing or removing battery cartridge. Failure to
hold the tool and the battery cartridge firmly may cause
them to slip off your hands and result in damage to the
tool and battery cartridge and a personal injury.
To install the battery cartridge, release the cover lock, and
open the battery cover. And insert the battery cartridge.
Align the tongue on the battery cartridge with the groove
in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. Then close the
battery cover. (Fig. 2)
To remove the battery cartridge, slide it from the tool while
sliding the button on the front of the cartridge.
CAUTION:
• Always install the battery cartridge fully in place. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being inserted
correctly.
Use with AC power:
Connect the plug to a power supply. (Fig. 3)
Turning on LED light (Fig. 4)
Press the switch once, the light shines brightly (high
mode). Press the switch again, the light shines mildly (low
mode). To turn off the light, press the switch once again.
Battery protection system (Fig. 5)
The tool is equipped with a battery protection system to
extend battery life.
When the battery becomes low, the LED lights go out
except one LED (the one on the second line center).
Then, after approximately five to ten minutes later, the
system automatically cuts off power.
OPERATION
CAUTION:
• This worklight is intended for field work use. Do not use
the worklight for household purpose.
• Always put the tool on flat and stable place. Otherwise
a falling accident may occur.
Adjusting the angle of the worklight (Fig. 6)
Loosen the knobs on the both side. Adjust the angle of
the worklight. Then tighten the knobs again.
Using with tripod or vise (optional accessories)
(Fig. 7)
CAUTION:
• Read carefully the instruction manuals of the
accessories before using them with the worklight.
• When using with tripod or vise, do not let the total
height exceed 1.75 m.
You can put the worklight on the tripod or vise to facilitate
the operation.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off, unplugged,
and the battery cartridge is removed before attempting
to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Only maintenance work described in this instruction
manual may be performed by the user. Any other
work must be carried out by Makita authorized service
centers.
Cleaning
From time to time wipe off the outside (tool body) of the
tool using a cloth dampened in soapy water.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should be
performed by Makita authorized service centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Makita genuine battery and charger
• Tripod
• Vise
• Anti-glare film
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
5