Table of Contents
Related Manuals for Makita 2012NB/2
Summary of Contents for Makita 2012NB/2
- Page 1 Planer MODEL 2012NB 003706 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w . m a k i t a t o o l s . c o m...
-
Page 2: Specifications
SPECIFICATIONS Model 2012NB Cutting width 304 mm (12”) 3.0 mm (1/8”) of stock width less than 150 mm (5-7/8”) 1.5 mm (1/16”) of stock width from Max. cutting depth 150 mm (5-7/8”) to 240 mm (9-1/2”) 1.0 mm (3/64”) of stock width from 240 mm (9-1/2”) to 304 mm (12”) Feed rate /min 8.5 m (27.9 ft.) /min. - Page 3 7. MAKE WORKSHOP KID PROOF with pad- 17. USE RECOMMENDED ACCESSORIES. locks, master switches, or by removing Consult the owner’s manual for recom- starter keys. mended accessories. The use of improper accessories may cause risk of injury to 8. DON’T FORCE TOOL. It will do the job bet- persons.
-
Page 4: Additional Safety Rules
USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. - Page 5 SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
-
Page 6: Installation
INSTALLATION Movement and transport of planer 003707 CAUTION: • Watch your step when moving the tool. Fold the sub-tables. Grasp the carrying handles when mov- ing the tool. When transporting it by vehicle, secure with a rope or other substantial means to prevent tipping or movement. 1. - Page 7 Dimensional adjustment 003710 Lower the main frame by turning the crank handle counter- clockwise until the indicator plate points to the scale gradua- tion indicating the desired finished dimension. One full turn of the crank handle moves the main frame 2 mm (3/32”) up or down.
- Page 8 Depth adjusting gauge 003713 Use the depth adjusting gauge when you need to predeter- mine the depth of cut more accurately. To do so, proceed as follows. 1. First, plane the workpiece at the predetermined depth of cut. Measure the thickness of the planed piece to know how much more stock you need to remove.
- Page 9 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Replacing planer blades CAUTION: • Handle the blades very carefully when removing or installing the blades to prevent cuts or injury from the blades and to prevent damage to the blades.
- Page 10 5. Blade 6. Claw 2. Installing blades 003717 CAUTION: • Use only Makita socket wrench provided to tighten the blade installation bolts. The use of any other socket wrench cause overtightening insufficient tightening of the bolts, resulting in severe injury.
- Page 11 Grip the magnetic holder and slip the heel of the set plate 003716 into the groove in the drum. Install the blade installation bolts. 1. Blade installation bolts 2. Set plate 3. Magnetic holder 4. Drum 5. Blade 6. Claw After tightening all the blade installation bolts lightly and 003717 evenly from the center to the outside, tighten them com-...
- Page 12 Loosen the thumb screws which secure the chip cover. 003723 Attach the hood to the planer and secure the chip cover and the hood together by tightening the thumb screws. 1. Chip cover 2. Thumb screw 3. Hood Planer stand (optional accessory) Place the stays on a level location and assemble the legs 003719 inside.
-
Page 13: Operation
The planer stand should be bolted with the four bolts to the 003721 floor using the bolt holes provided in the legs. 1. Bolt OPERATION 003724 CAUTION: • Two or more pieces of narrow but similar thickness stock can be passed through the planer side by side. However, allow some spacing between the stock to permit the feed rollers to grip the thinnest piece of stock. -
Page 14: Maintenance
003726 Less than 130 mm (5-1/8”) long Less than 130 mm (5-1/8”) long Less than 130mm (5-1/8”) More than 130mm (5-1/8”) Having a groove more than 130mm (5-1/8”) wide Having a groove more than 130mm (5-1/8”) wide 130mm (5-1/8”) Having grooves at intervals of 130 mm (5-1/8”) wide Having grooves at intervals of 130 mm (5-1/8”) wide •... - Page 15 Always brush off dirt, chips and foreign matter adhering to the roller surfaces, motor vents and drums. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
- Page 16 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
- Page 17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold...
- Page 18 Design Repair Service Industrial Maintenance Features Durability Home Maintenance Size Power Hobby Price Other ( Other ( Makita Brand 5. Any comments: DATE PURCHASED MODEL NO. MONTH YEAR SERIAL NO. STATUS INTL. LAST NAME / COMPANY NAME Married Single STREET ADRESS...
-
Page 19: Factory Service Centers
Date Purchased When you need service: Send complete tool (prepaid) to one Dealer’s Name & Address of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of Model No. - Page 20 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.