Makita DUR193 Instruction Manual
Cordless grass trimmer
Hide thumbs
Also See for DUR193:
- Instruction manual (117 pages) ,
- Instruction manual (93 pages) ,
- Instruction manual (117 pages)
Related Manuals for Makita DUR193
Summary of Contents for Makita DUR193
- Page 1 INSTRUCTION MANUAL Cordless Grass Trimmer DUR193 Read before use. Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DUR193 No load speed 7,800 min (without cutting tool) Overall length 1,228 - 1,436 mm Nylon cord diameter 1.65 mm Applicable cutting tool and Nylon cutting head (P/N: 260 mm cutting diameter 191Y39-5) Rated voltage D.C. 18 V Net weight 2.3 - 2.6 kg... -
Page 3: Ec Declaration Of Conformity
Vibration Applicable standard : EN50636-2-91 Type Left hand Right hand (m/s Uncertainty K (m/s Uncertainty K (m/s (m/s Nylon cutting head NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another. NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure. -
Page 4: Save All Warnings And Instruc- Tions For Future Reference
Save all warnings and instruc- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left tions for future reference. attached to a rotating part of the power tool may The term "power tool" in the warnings refers to your result in personal injury. - Page 5 Maintain power tools and accessories. Check for IMPORTANT SAFETY misalignment or binding of moving parts, breakage INSTRUCTIONS of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused WARNING: Read all safety warnings and by poorly maintained power tools.
- Page 6 Personal protective equipment Electrical and battery safety Avoid dangerous environment. Don't use the tool in damp or wet locations or expose it to rain. Water entering the tool will increase the risk of electric shock. Recharge only with the charger specified by the manufacturer.
- Page 7 Switch on the motor only when hands and feet 19. Take a rest to prevent loss of control caused are away from the cutting tool. by fatigue. We recommend to take a 10 to 20-minute rest every hour. Before starting make sure that the cutting tool has no contact with hard objects such as branches, stones 20.
-
Page 8: Parts Description
Hanger for shoulder Only use genuine Makita batteries. harness Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting Battery cartridge causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. 8 ENGLISH... - Page 9 Installing the wire guard ASSEMBLY NOTICE: Do not expand the wire guard outward CAUTION: Always be sure that the tool is too much. Otherwise it may break. switched off and the battery cartridge is removed before carrying out any work on the tool. CAUTION: Never start the tool unless it is completely assembled.
-
Page 10: Functional Description
Makita. Installing or removing battery If you put on the shoulder harness included in the tool package and the shoulder harness of the back-... -
Page 11: Indication Lamp
If you turn the tool on, the motor runs without pressing the lock-off button. Ask your local again but stops soon. In this situation, remove and Makita Service Center for repairs. recharge the battery. WARNING: Never disable the lock function or Indicating the remaining battery tape down the lock-off button. -
Page 12: Nylon Cutting Head
The indication lamp blinks or lights up when the battery The cutting angle can be adjusted in 5 steps. To change becomes low or the tool is overloaded. Refer to the the cutting angle, change the angle of the motor hous- following table for the status and action to be taken. ing while pressing the angle adjustment button. - Page 13 To adjust the shaft length, open the lock lever, then adjust the length of the shaft, and then close the lock lever. Fig.18 ► 1 . Lock lever 2. Shaft Adjust the position of the loop handle so that you can hold the loop handle when lowering your left hand. Fig.20 NOTICE: Do not force the trimmer in densely growing grass. Fig.19 ► 1 . Loop handle Cutting the grass Hold the grass trimmer with both hands, and move the grass trimmer from right to left slowly.
-
Page 14: Maintenance
To maintain product SAFETY and RELIABILITY, when you shorten the shaft to the minimum length. repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Lift up the wire guard, and move the grass trimmer as Centers, always using Makita replacement parts. -
Page 15: Cleaning The Tool
Cleaning the tool Clean the tool by wiping off dust, dirt, or cut off grass with a dry cloth or one dipped in soapy water and wrung out. If the cut off grass is adhered to the motor housing, be sure to remove it. Fig.28 ► 1 . Wire guard Fig.27 ► 1 . Motor housing Storage When storing the tool, raise the wire guard, shorten the shaft, and then fold the loop handle. - Page 16 Replace the nylon cord if the cord is not feeding any more. 8 12 Fig.30 ► ( 1) Up to 8 m (2) 70 - 80 mm 16 ENGLISH...
-
Page 17: Troubleshooting
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy Motor does not run. Battery cartridge is not installed. Install the battery cartridge. - Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885961-914 www.makita.com 20211116...