Page 1 NOTICE Note that when converting this document from its original format to a .pdf file, some minor font and format changes may occur causing slight variations. When viewing and printing this document, we cannot guarantee that your specific PC or printer will support all of the fonts or graphics.
Page 2 ROGRAMMING ANUAL I N T - 1 0 7 3 ( I P K I I ) O C U M E N T E V I S I O N E L E A S E 1 0 0 0 )
Page 4 NEC Unified Solutions, Inc. reserves the right to change the specifications, functions, or features at any time without notice. NEC Unified Solutions, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Unified Solutions, Inc. and shall not be reproduced without prior written approval of NEC Unified Solutions, Inc.
Page 6 Electra Elite IPK II General Description Manual This Manual provides general information about the system, its features, system configuration and standards. This manual provides an overview of the Electra Elite IPK II system and can be used to present information to potential customers.
Page 8: Table Of Contents
What the Softkey Display Prompts Mean ......... 1-7 Section 9 System Number Plan/Capacities ............1-8 Chapter 2 Programming the Electra Elite IPK II Section 1 Programming Your System ............... 2-1 Program 10 : System Configuration Setup 10-01 : Time and Date ................2-3 10-02 : Location Setup ................
Page 9 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ 10-14 : Managed Network Setup ............2-21 10-15 : Client Information Setup ............2-22 10-16 : Option Information Setup ............2-23 10-20 : LAN Setup for External Equipment ......... 2-25 10-21 : CPUII Hardware Setup ............2-26 10-24 : Daylight Savings Setup ............
Page 10 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ 12-08 : Night Mode Service Range ............2-78 Program 13 : Speed Dialing 13-01 : Speed Dialing Option Setup ............ 2-79 13-02 : Group Speed Dialing Bins ............2-80 13-03 : Speed Dialing Group Assignment for Extensions ....2-81 13-04 : Speed Dialing Number and Name ...........
Page 11 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ 15-15 : Wireless DECT Terminal Basic Data Setup ......2-136 15-17 : CO Message Waiting Indication ..........2-139 15-18 : Virtual Extension Key Enhanced Options ......2-140 15-20 : LCD Line Key Name Assignment .......... 2-141 Program 16 : Department Group Setup 16-01 : Department Group Basic Data Setup ........
Page 12 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ 20-25 : ISDN Options ................. 2-192 20-26 : Multiplier Changing CO ............2-194 20-28 : Trunk to Trunk Conversation ..........2-195 20-29 : Timer Class for Extension ............. 2-196 20-30 : Timer Class for Trunks ............2-197 20-31 : Timer Class Timer Assignment ..........
Page 13 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ 22-07 : DIL Assignment ..............2-233 22-08 : DIL/IRG No Answer Destination ..........2-234 22-09 : DID Basic Data Setup ............2-235 22-10 : DID Translation Table Setup ..........2-237 22-11 : DID Translation Number Conversion ........2-239 22-12 : DID Intercept Ring Group ............
Page 14 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ 25-08 : DISA User ID Setup ............... 2-274 25-09 : Class of Service for DISA Users ..........2-275 25-10 : Trunk Group Routing for DISA ..........2-276 25-11 : DISA Toll Restriction Class ........... 2-277 25-12 : Alternate Trunk Group Routing for DISA .......
Page 15 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ Program 32 : Door Box and Sensor Setup 32-01 : Door Box Timers ..............2-319 32-02 : Door Box Ring Assignment ........... 2-320 32-03 : Door Box Basic Setup ............2-321 Program 33 : CTA and ACI Setup 33-01 : ACI Port Type Setup .............
Page 16 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ 40-07 : Voice Prompt Language Assignment for VRS ....... 2-354 40-08 : Voice Prompt Language Assignment for Mailboxes ....2-355 40-09 : Voice Mail Multiple Address Group Setup ......2-356 40-10 : Voice Announcement Service Option ........2-357 40-11 : Pre-Amble Message Assignment ..........
Page 17 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ Program 44 : ARS/F-Route Setup 44-01 : System Options for ARS/F-Route ......... 2-393 44-02 : Dial Analysis Table for ARS/F-Route Access ......2-394 44-03 : Dial Analysis Extension Table ..........2-396 44-04 : ARS/F-Route Selection for Time Schedule ......2-398 44-05 : ARS/F-Route Table ...............
Page 18 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ Program 50 : Common Channel Interoffice Signaling Service 50-01 : CCIS System Setting ............. 2-461 50-02 : Connecting System Settings ..........2-462 50-03 : CCIS Destination System Settings ........2-464 50-04 : CCIS Office Code Assignment ..........2-465 50-05 : CCIS Maximum Call Forwarding Hop Counter ......
Page 19 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ Program 82 : Basic Hardware Setup for Extension 82-01 : Incoming Ring Tone .............. 2-501 82-03 : DSS Console LED Pattern Setup .......... 2-503 82-08 : Sidetone Volume Setup ............2-505 82-11 : SLI Initial Setup ..............2-506 82-12 : OPX Initial Data ..............
Page 20 Electra Elite IPK II Document Revision 1 ___________________________________________________________________________________ 90-05 : Slot Control ................2-542 90-06 : Trunk Control ................. 2-543 90-07 : Extension Control ..............2-544 90-08 : System Reset ................ 2-545 90-09 : Automatic System Reset Time ..........2-546 90-10 : System Alarm Setup ..............
Page 21 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ Table of Contents...
Page 22 LIST OF TABLES ___________________________________________________________________________________ Table 1-1 Keys for Entering Data ..................1-4 Table 1-2 Keys for Entering Names .................. 1-5 Table 1-3 Softkey Display Prompts ................... 1-7 Table 1-4 System Number Plan/Capacities ............... 1-8 Table 2-1 Programming Modes ..................2-1 Table 2-2 System Numbering Default Settings ...............
Page 23 Document Revision 1 Electra Elite IPK II ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ List of Tables...
Page 24: Chapter 1 Introduction
Introduction EFORE TART ROGRAMMING ECTION Before customizing your system be sure to read this chapter first. This chapter provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this chapter, you find out about each program, the features that the program affects and how to enter the program data into system memory.
Page 25: How To Enter Programming Mode
Document Revision 1 Electra Elite IPK II Feature Cross Reference provides you with a table of all the features affected by the program. You will want to keep the referenced features in mind when you change a program. Customizing a feature may have an effect on another feature that you did not intend.
Page 26 Electra Elite IPK II Document Revision 1 User Password Level Programs at this Level Name 47544 necii 1 (MF) Manufacturer (MF): All programs 12345678 tech 2 (IN) Installation (IN): All programs in this section not listed below for SA and...
Page 27: Table 1-1 Keys For Entering Data
Document Revision 1 Electra Elite IPK II SING EYS TO ROUND IN THE ROGRAMS ECTION Once you enter the programming mode, use the keys in the following chart to enter data, edit data and move around in the menus. Table 1-1 Keys for Entering Data Keys for Entering Data Use this key...
Page 28: Programming Names And Text Messages
Electra Elite IPK II Document Revision 1 Table 1-1 Keys for Entering Data (Continued) Keys for Entering Data Use this key... When you want to... Scroll backward through a list of entry numbers (e.g., from extension etc.) or through entries in a table (e.g., Common Permit Table).
Page 29 OFTKEYS ROGRAMMING ECTION Each Electra Elite IPK II display telephone provides interactive Softkeys for intuitive feature access. The options for these keys will automatically change depending on where you are in the system programming. Simply press the Softkey located below the option you wish and the display will change accordingly.
Page 30: What The Softkey Display Prompts Mean
Electra Elite IPK II Document Revision 1 HAT THE OFTKEY ISPLAY ROMPTS ECTION When using a display telephone in programming mode, various Softkey options are displayed. These keys will allow you to easily select, scan, or move through the programs.
Page 31: System Number Plan/Capacities
Document Revision 1 Electra Elite IPK II YSTEM UMBER APACITIES ECTION The following table provides the capacities for the Electra Elite IPK II system. Table 1-4 System Number Plan/Capacities System Number Plan/Capacities System Type Number Plan/Capacities System Analog Caller ID Detector...
Page 32 Virtual Extension Port Numbers 001~256 Virtual Extension Number Range Undefined PGD(2)-U10 Modules ADA (Recording Jack) Adapters Electra Elite IPK II Wireless DECT Base Stations Electra Elite IPK II Wireless DECT Telephones Door Boxes Door Box Numbers DSS Consoles Numbers: 60 Button DSS Console...
Page 33 Document Revision 1 Electra Elite IPK II Table 1-4 System Number Plan/Capacities (Continued) System Number Plan/Capacities System Type Number Plan/Capacities Speed Dialing Speed Dialing Groups Speed Dialing Bins 0~1999 Speed Dialing Table-Common 1000 ACD Groups ACD Agent Extensions ACI Groups...
Page 34 Electra Elite IPK II Document Revision 1 Table 1-4 System Number Plan/Capacities (Continued) System Number Plan/Capacities System Type Number Plan/Capacities Paging and Park Internal Page Group Numbers 0, 1~9 or 01~64 External Page Group Numbers 0, 1~8 External Speakers CPU II( )-U10...
Page 35 Level 4 (SB) 9999 PCPro/WebPro User Name: ADMIN2 Programming Password Users Footnotes Extension numbers can be one to eight digits long. Refer to the Flexible System Numbering feature in the Electra Elite IPK II Features and Specifications manual. 1 - 12 Introduction...
Page 36: Programming The Electra Elite Ipk Ii
ROGRAMMING YSTEM ECTION The information contained in this chapter provides the information necessary to properly program your Electra Elite IPK II system. The programming blocks are organized into the following programming modes. Table 2-1 Programming Modes Program Number : Program Name...
Page 37 Program 84 : Hardware Setup for VoIP Program 85 : HUB(8) LAN Setup Program 90 : Maintenance Program (no Programs 86~89) Program 91 : IPK II Wireless DECT PS Entry Program 92 : Copy Program 2 - 2 Programming the Electra Elite IPK II...
Page 38: Program 10 : System Configuration Setup
Enter two digits for the hour (00~23). Minute 00~59 No Setting Enter two digits for the minute (00~59). Second 00~59 No Setting Enter two digits for the second (00~59). Conditions None Feature Cross Reference Clock/Calendar Display Electra Elite IPK II Programming Manual 2 - 3...
Page 39: Location Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-02 : Location Setup Level: Description Use Program 10-02 : Location Setup to define the location of the installed system. Input Data Item Item Input Data Default...
Page 40: Etu Setup
24 logic ports are automatically assigned to a DTI (T1) line. T1 Signal Format Selection 0 = D4 (12 Multi Frame) 1 = ESF (24 Multi Frame) Clear Channel Selection Electra Elite IPK II Programming Manual 2 - 5...
Page 41 Document Revision 1 Electra Elite IPK II Line Length Selection 0 = 0 feet ~ 133 feet 1 = 134 feet ~ 266 feet 2 = 267 feet ~ 399 feet 3 = 400 feet ~ 533 feet 4 = 534 feet ~ 655 feet...
Page 42 Item Item Input Data Default Logical Port Number 0~256 --- Not Used --- Transmit Gain Level (S-Level) 1~63 (-15.5 +15.5dB) 32 (0dB) Receive Gain Level (R-Level) 1~63 (-15.5 +15.5dB) 32 (0dB) Electra Elite IPK II Programming Manual 2 - 7...
Page 43 Document Revision 1 Electra Elite IPK II For COIU Unit Setup Physical Port Number 01~08 Item Item Input Data Default 0~200 Logical Port Number For TLI PKG Setup Physical Port Number 01~02 Item Item Input Data Default 0~200 Logical Port Number...
Page 44 (Only when Dialing Sending Mode (10- 03-08) is set for 1 (Overlap Sending) --- Not Used --- --- Not Used --- --- Not Used --- --- Not Used --- --- Not Used --- Electra Elite IPK II Programming Manual 2 - 9...
Page 45 Document Revision 1 Electra Elite IPK II For PRI PKG Setup ISDN Line Number 01~24 Item Item Input Data Default --- Not Used --- Logical Port Number = for T-Bus 1~200 The start port number of a PRI line is displayed.
Page 46 Line Length Selection = 0 feet ~ 133 feet = 134 feet ~ 266 feet = 267 feet ~ 399 feet = 400 feet ~ 533 feet = 534 feet ~ 655 feet Electra Elite IPK II Programming Manual 2 - 11...
Page 47 Document Revision 1 Electra Elite IPK II DTI Trunk Type Assignment = CO = E&M = DID = ANI For VMS/FMS PKG Setup Physical Port Number 01~16 Item Item Input Data Default Logical Port Number 0~256 Conditions When changing a defined terminal type, first set the type to ‘0’ and then plug the new device in to have the system automatically define it or redefine the type manually.
Page 48: Music On Hold Setup
MOH music source use the same Music on Hold source. --- Not Used --- Audio Gain Setup 1-63 (-15.5 +15.5dB) (0dB) Conditions None Feature Cross Reference Analog Communications Interface (ACI) Background Music Music on Hold Electra Elite IPK II Programming Manual 2 - 13...
Page 49: General Purpose Relay Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-05 : General Purpose Relay Setup Level: Description Use Program 10-05 : General Purpose Relay Setup to define which Relay circuits (5~8) on PGD(2)-U10 Adapter are used for General Purpose Relay.
Page 50: Isdn Bri Setup
0 = Route by Called Party Number DID Mode 1 = Route by Redirecting Number SPID 1 Dial up to 20 digits SPID 2 Dial up to 20 digits Conditions None Feature Cross Reference ISDN Compatibility Electra Elite IPK II Programming Manual 2 - 15...
Page 51: Ringing Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-08 : Ringing Setup Level: Description Use Program 10-08 : Ringing Setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk’s LED flashes.
Page 52: Dtmf And Dial Tone Circuit Setup
CPUII for either DTMF receiving or dial tone detection. The CPUII has 16 circuits initially. On the Electra Elite IPK II, with additional PGD(2)-U10 ADPs installed, the system can provide a total of 64 circuits (32 + 32). These are used as follows:...
Page 53: Cpuii Network Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-12 : CPUII Network Setup Level: Description Use Program 10-12 : CPUII Network Setup to setup the IP Address, Subnet-Mask, and Default Gateway addresses. Caution! If any of the IPK Address or NIC settings are changed, the system must be reset in order for the changes to take affect.
Page 54 4 = 10Mbps, Half Duplex --- Not Used --- Conditions The system must be reset in order for these changes to take affect. Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 19...
Page 55: In-Dhcp Server Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-13 : In-DHCP Server Setup Level: Description Use Program 10-13 : In-DHCP Server Setup to setup the DHCP Server built into the CPUII. Caution! The system must be reset in order for these changes to take affect.
Page 56: Managed Network Setup
128.1.0.1 ~ 191.254.255.254 selected in 10-13-04, a Scope 2~10: 192.0.1.1 ~ 223.255.254.254 maximum of ten scope ranges 0.0.0.0 can be entered. Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 21...
Page 57: Client Information Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-15 : Client Information Setup Level: Description Use Program 10-15 : Client Information Setup to set up the client information when the DHCP server needs to assign a fixed IP address to clients.
Page 58: Option Information Setup
128.1.0.1 ~ 191.254.255.254 192.0.1.1 ~ 223.255.254.254 --- Not Used --- --- Not Used --- Code number 0-255 129 (Fixed) IP address 172.16.0.10 1.0.0.1 ~ 126.255.255.254 128.1.0.1 ~ 191.254.255.254 192.0.1.1 ~ 223.255.254.254 Electra Elite IPK II Programming Manual 2 - 23...
Page 59 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) 2 - 24 Program 10 : System Configuration Setup...
Page 60: Lan Setup For External Equipment
External Device 1 and 2 = 0 External Device 3 = 0 External Device 4 = 0 External Device 5 = 0 --- Not Used --- Keep Alive Time 1~255 (sec) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 25...
Page 61: Cpuii Hardware Setup
Document Revision 1 Electra Elite IPK II Program 10 : System Configuration Setup 10-21 : CPUII Hardware Setup Level: Description Use Program 10-21 : CPUII Hardware Setup to set up various hardware, such as the baud rate of COM port and the switch for control on CPUII.
Page 62: Daylight Savings Setup
End of Week 0 = Last Week of Month Enter the week of the month the system should adjust the time for standard time (0 = last week of the month or 1~5). Electra Elite IPK II Programming Manual 2 - 27...
Page 63 Document Revision 1 Electra Elite IPK II Input Data (Continued) Item Related Item Input Data Default Program End of Week Day (Sun=1, Mon=2, etc.) Enter the day of the week the system should adjust the time for daylight savings time (01 = Sunday, 02 = Monday, etc.).
Page 64: Bgm Resource Setup
1 = ACI Port ACI Port Number for BGM Source 0 ~ 96 (only used if 10-38-01 is set to 1) Conditions None Feature Cross Reference Analog Communications Interface (ACI) Background Music Electra Elite IPK II Programming Manual 2 - 29...
Page 65 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 30 Program 10 : System Configuration Setup...
Page 66: Program 11 : System Numbering
Entering two digits lets you define codes based on the first two digits a user dials. For example, entering 60 allows you to define the function of all codes beginning with 60. In the default program, only * and # use 2-digit codes. All Electra Elite IPK II Programming Manual 2 - 31...
Page 67: Table 2-2 System Numbering Default Settings
Document Revision 1 Electra Elite IPK II the other codes are single digit. If you enter a two digit code between 0 and 9, be sure to make separate entries for all the other two digit codes within the range as well.
Page 68 Table 2-2 System Numbering Default Settings Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default Electra Elite IPK II Programming Manual 2 - 33...
Page 69 Document Revision 1 Electra Elite IPK II Table 2-2 System Numbering Default Settings (Continued) Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default...
Page 70 Table 2-2 System Numbering Default Settings (Continued) Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default Electra Elite IPK II Programming Manual 2 - 35...
Page 71 Document Revision 1 Electra Elite IPK II Table 2-2 System Numbering Default Settings (Continued) Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default...
Page 72 Table 2-2 System Numbering Default Settings (Continued) Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default Electra Elite IPK II Programming Manual 2 - 37...
Page 73 Document Revision 1 Electra Elite IPK II Table 2-2 System Numbering Default Settings (Continued) Dial Types: 1=Service Code, 2=Extension Number, 3=Trunk Access, 4=Special Trunk Access, 5=Operator Access, 6=Flexible Routing, 0=Not Used Dialed Number of Digits Dial Type Required Default Default...
Page 74 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Flexible System Numbering Electra Elite IPK II Programming Manual 2 - 39...
Page 75: Extension Numbering
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-02 : Extension Numbering Level: Description to set the extension number. The extension Program 11-02 : Extension Numbering number can be up to eight digits long. The first/second digit(s) of the number should be assigned in Program 11-01.
Page 76 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Department Calling Flexible System Numbering Intercom Electra Elite IPK II Programming Manual 2 - 41...
Page 77: Virtual Extension Numbering
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-04 : Virtual Extension Numbering Level: Description to define the virtual extension Program 11-04 : Virtual Extension Numbering numbers. The extension number can be up to eight digits long. The first/second digit(s) of the number should be assigned in Program 11-01.
Page 78 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Flexible System Numbering Multiple Directory Numbers / Call Coverage Electra Elite IPK II Programming Manual 2 - 43...
Page 79: Aci Extension Numbering
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-06 : ACI Extension Numbering Level: Description to define the virtual extension number Program 11-06 : ACI Extension Numbering to be used for the ACI. The extension number can be up to eight digits long. The first/ second digit(s) of the number should be assigned in Program 11-01.
Page 80: Department Group Pilot Numbers
16-03 : Secondary Department The extension number cannot be Group duplicated in Programs 11-02, 11-04, 11-06 and 11-08. Default No Setting Conditions None Feature Cross Reference Department Calling Department Step Calling Electra Elite IPK II Programming Manual 2 - 45...
Page 81: Aci Group Pilot Number
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-08 : ACI Group Pilot Number Level: Description to assign the pilot number to the ACI Program 11-08 : ACI Group Pilot Number Groups set in Program 33-02. The pilot number can be up to four digits long. The first/second digit(s) of the number should be assigned in Program 11-01 as type 2.
Page 82: Trunk Access Code
14-01 : Trunk Basic (normally 9). This Data Setup is the code 14-05 : Trunk Group extension users dial to access 14-06 : Trunk Group Automatic Route Routing Selection. Electra Elite IPK II Programming Manual 2 - 47...
Page 83 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Description Related Program 2nd Trunk Dial Use this program 11-01 : System Route Access (up to 4 Setting Numbering to define Code digits) additional trunk 14-01 : Trunk Basic access codes.
Page 84: Service Code Setup (For System Administrator)
Each Trunk Line Setting the Destination for 24-04-01 Automatic Trunk Transfer --- Not Used --- --- Not Used --- --- Not Used --- Night Mode Switching for Other 12-xx Group 20-07-01 Electra Elite IPK II Programming Manual 2 - 49...
Page 85 Document Revision 1 Electra Elite IPK II Input Data Item Related Item Terminals Default Program --- Not Used --- --- Not Used --- --- Not Used --- Leaving Message Waiting 11-11-09 Dial Block by Supervisor 90-19 Off-Premise Call Forward by Door...
Page 86 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Refer to Input Data chart on the previous pages. Electra Elite IPK II Programming Manual 2 - 51...
Page 87: Service Code Setup (For Setup/Entry Operation)
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-11 : Service Code Setup (for Setup/Entry Operation) Level: Description Use Program 11-11 : Service Code Setup (for Setup/Entry Operation) to customize the Service Codes which are used for registration and setup. You can customize additional Service Codes in Programs 11-10, and 11-12 ~ 11-16.
Page 88 DND Cancellation for Each Extension Group MLT, SLT --- Not Used --- Dial Block MLT, SLT Temporary Toll Restriction Override MLT, SLT 21-07 MLT, SLT Pilot Group Withdrawing MLT, SLT 21-14 Toll Restriction Override Electra Elite IPK II Programming Manual 2 - 53...
Page 89 Electra Out of Range Elite IPK II Wireless Customize the service code to be used when setting a Electra Elite IPK II Wireless telephone to transfer calls when out of range. Headset Mode Switching MLT, SLT Auto Attendant MLT, SLT...
Page 90 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Refer to the Input Data chart above. Electra Elite IPK II Programming Manual 2 - 55...
Page 91: Service Code Setup (For Service Access)
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-12 : Service Code Setup (for Service Access) Level: Description Use Program 11-12 : Service Code Setup (for Service Access) to customize the Service Codes which are used for service access. You can customize additional Service Codes in Programs 11-10, 11-11, and 11-13 through 11-16.
Page 92 Park Hold MLT, SLT 24-03 MLT, SLT 24-03 Answer for Park Hold Group Hold MLT, SLT Answer for Group Hold MLT, SLT MLT, SLT Station Park Hold Door Box Access MLT, SLT Electra Elite IPK II Programming Manual 2 - 57...
Page 93 Document Revision 1 Electra Elite IPK II Input Data (Continued) Item Related Item Terminals Default Program Common Canceling Service Code MLT, SLT General Purpose Indication --- Not Used --- Station Speed Dialing MLT, SLT Voice Over 11-16-08 Flash on Trunk lines...
Page 94 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Refer to the Input Data chart on the previous pages. Electra Elite IPK II Programming Manual 2 - 59...
Page 95: Service Code Setup (For Acd)
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-13 : Service Code Setup (for ACD) Level: Description Use Program 11-13 : Service Code Setup (for ACD) to customize the Service Codes which are used with the Automatic Call Distribution (ACD) feature. You can customize additional Service Codes in Programs 11-10 through 11-12 and 11-14 ~ 11-16.
Page 96 ‘169 04’. ACD Agent Changing Own ACD Group Using this service code, an ACD Agent can reassign themselves to another ACD Group. Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 61...
Page 97: Service Code Setup (For Hotel)
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-14 : Service Code Setup (for Hotel) Level: Description Use Program 11-14 : Service Code Setup (for Hotel) to customize the Service Codes which are used with the Hotel/Motel feature. You can customize additional Service Codes in Programs 11-10 through 11-13, 11-15 and 11-16.
Page 98 --- Not Used --- Room Status Change for Other Extension MLT, SLT Room Status Output MLT, SLT Hotel Room Monitor MLT, SLT ---Not Used --- Conditions None Feature Cross Reference Hotel/Motel Electra Elite IPK II Programming Manual 2 - 63...
Page 99: Service Code Setup, Administrative (For Special Access)
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-15 : Service Code Setup, Administrative (for Special Access) Level: Description Use Program 11-15 : Service Code Setup, Administrative (for Special Access) to customize the special access Service Codes which are used by the administrator in the Hotel/Motel feature.
Page 100 Transfer to Incoming Ring Group Setting --- Not Used --- Ethernet Port Reset MLT, SLT Extension Data Swap MLT, SLT --- Not Used --- Modem Access MLT, SLT Conditions None Feature Cross Reference Hotel/Motel Electra Elite IPK II Programming Manual 2 - 65...
Page 101: Single Digit Service Code Setup
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-16 : Single Digit Service Code Setup Level: Description Use Program 11-16 : Single Digit Service Code Setup to customize the one-digit Service Codes used when a busy or ring back signal is heard. You can customize additional Service Codes in Programs 11-10 through 11-15.
Page 102 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Refer to the Input Data chart on previous pages. Electra Elite IPK II Programming Manual 2 - 67...
Page 103: Acd Group Pilot Number
Document Revision 1 Electra Elite IPK II Program 11 : System Numbering 11-17 : ACD Group Pilot Number Level: Description to assign the ACD Master Number for Program 11-17 : ACD Group Pilot Number each ACD Group. This is the number users dial to transfer calls to the ACD Group.
Page 104: Program 12 : Night Mode Setup
Service for the system. --- Not Used --- Even if the operation mode is changed manually, the operation mode changes according to the schedule set up. Conditions None Feature Cross Reference Night Service Electra Elite IPK II Programming Manual 2 - 69...
Page 105: Automatic Night Service
Document Revision 1 Electra Elite IPK II Program 12 : Night Mode Setup 12-02 : Automatic Night Service Level: Description Use Program 12-02 : Automatic Night Service Patterns to define the daily pattern of the Automatic Mode Switching. Each Mode Group has 10 patterns. These patterns are used in Programs 12-03 and 12-04.
Page 106 End Time Mode 0000 0000 0000 0000 0000 0000 Time Pattern 3 Set Time Number Start Time End Time Mode 0000 0000 0000 0000 Conditions None Feature Cross Reference Night Service Electra Elite IPK II Programming Manual 2 - 71...
Page 107: Weekly Night Service Switching
Document Revision 1 Electra Elite IPK II Program 12 : Night Mode Setup 12-03 : Weekly Night Service Switching Level: Description Use Program 12-03 : Weekly Night Service Switching to define a weekly schedule of night-switch settings. Input Data Night Mode Service Group Number...
Page 108 Day of the Week Pattern Number 01 = Sunday 02 = Monday 03 = Tuesday 04 = Wednesday 05 = Thursday 06 = Friday 07 = Saturday Conditions None Feature Cross Reference Night Service Electra Elite IPK II Programming Manual 2 - 73...
Page 109: Holiday Night Service Switching
Document Revision 1 Electra Elite IPK II Program 12 : Night Mode Setup 12-04 : Holiday Night Service Switching Level: Description Use Program 12-04 : Holiday Night Service Switching to define a yearly schedule of holiday night-switch settings. This schedule is used for the setting of special days which the company is expected to be closed, such as a national holiday.
Page 110: Night Mode Group Assignment For Extensions
Use Program 12-05 : Night Mode Group Assignment for Extensions to a assign Day/Night Mode Group for each extension. Input Data Extension Number Maximum: 8 Digits Item Night Mode Service Default Group Number 01~32 Conditions None Feature Cross Reference Night Service Electra Elite IPK II Programming Manual 2 - 75...
Page 111: Night Mode Group Assignment For Trunks
Document Revision 1 Electra Elite IPK II Program 12 : Night Mode Setup 12-06 : Night Mode Group Assignment for Trunks Level: Description Use Program 12-06 : Night Mode Group Assignment for Trunks to assign a Day/ Night Mode Group for each trunk port.
Page 112: Text Data For Night Mode
Mode 3 = <Midnight> Mode 4 = <Rest> Mode 5 = <Day2> Mode 6 = <Night2> Mode 7 = <Midnight2> Mode 8 = <Rest2> Conditions None Feature Cross Reference Night Service Electra Elite IPK II Programming Manual 2 - 77...
Page 113: Night Mode Service Range
Document Revision 1 Electra Elite IPK II Program 12 : Night Mode Setup 12-08 : Night Mode Service Range Level: Description Use Program 12-08 : Night Mode Service Range to define the changing range of toggle key for each Day/Night Mode.
Page 114: Program 13 : Speed Dialing
--- Not Used --- Number of Common Speed 0~2000 1000 13-04 Dialing Bins = No Common Speed Dialing 100 bins per 1 unit Conditions None Feature Cross Reference Speed Dial - System/Group/Station Electra Elite IPK II Programming Manual 2 - 79...
Page 115: Group Speed Dialing Bins
Document Revision 1 Electra Elite IPK II Program 13 : Speed Dialing 13-02 : Group Speed Dialing Bins Level: Description to define the range of bin numbers to Program 13-02 : Group Speed Dialing Bins be used by each Speed Dialing group. (Refer to...
Page 116: Speed Dialing Group Assignment For Extensions
Speed Dialing Group for each extension. There are 64 Speed Dialing groups that are available. Input Data Extension Number Up to 8 digits Item No. Group Number Default Value 01~64 Conditions None Feature Cross Reference Speed Dial - System/Group/Station Electra Elite IPK II Programming Manual 2 - 81...
Page 117: Speed Dialing Number And Name
Document Revision 1 Electra Elite IPK II Program 13 : Speed Dialing 13-04 : Speed Dialing Number and Name Level: Description to store Speed Dialing data into Program 13-04 : Speed Dialing Number and Name the Speed Dialing areas. This program is also used to define the names assigned to the Speed Dialing numbers.
Page 118 Incoming Ring Pattern 13-04-03 0 = Normal Pattern 1 ~ 4 = Tone Pattern (1~4) 5 ~ 9 = Scale Pattern (1~5) Conditions None Feature Cross Reference Speed Dial - System/Group/Station Electra Elite IPK II Programming Manual 2 - 83...
Page 119: Speed Dial Trunk Group
Document Revision 1 Electra Elite IPK II Program 13 : Speed Dialing 13-05 : Speed Dial Trunk Group Level: Description Use Program 13-05 : Speed Dialing Trunk Group to define the trunk group to be seized for each Speed Dialing number.
Page 120: Program 14 : Trunk, Basic Setup
(-15.5 ~ +15.5dB Use this option to in 0.5dB intervals) select the CODEC gain for the trunk. The option sets the amount of gain (signal amplification) for the trunk you are programming. Electra Elite IPK II Programming Manual 2 - 85...
Page 121 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Transmit Gain Level 1~63 22 (-5dB) for Conference and (-15.5 ~ +15.5dB Transfer Calls in 0.5dB intervals) Use this option to select the CODEC gain type used by the...
Page 122 Cutoff feature for each trunk. = Disable 20-21-01 Long Conversation Alarm Before Cutoff (No) 20-21-02 = Enable Use this option to (Yes) enable or disable the Long Conversation Alarm for each trunk. Electra Elite IPK II Programming Manual 2 - 87...
Page 123 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Forced Release of = Disable 24-01-01 Held Call (No) 24-01-05 = Enable Use this option to (Yes) enable/disable forced release for calls on Hold. If enabled, the...
Page 124 Mode = Enable (Yes) Continued/ = Disable Discontinued Trunk- (No) to-Trunk = Enable Conversation (Yes) Automatic Trunk-to- 0 = Normal Trunk Transfer Mode Transfer (Normal) 1 = Step Transfer (Step) Electra Elite IPK II Programming Manual 2 - 89...
Page 125 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Caller ID Refuse = Disable Setup (No) = Enable (Yes) Effectivity of 0 = No Effect (No) “Conversation 1 = Available (Yes) Recording Destination for Extension”...
Page 126: Analog Trunk Data Setup
If disabled, the system outdials on the trunks without monitoring for dial tone. Pause at 1st Digit after Line Seize in = No Pause (No) 21-01-06 Manual Dial Mode = Pause (Yes) Electra Elite IPK II Programming Manual 2 - 91...
Page 127 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program DP to DTMF Conversion Options 0 = Automatic 21-01-03 1 = Automatic and Manual Determine how a user can convert a 2 = Manual Dial Pulse (DP) call to a DTMF call. For each trunk, set the type of DP to DTMF conversion required.
Page 128 Use this to specify whether or not CO/ PBX calls follow Synchronous Ringing. Synchronous Ringing does not apply to incoming DID calls, off-hook ringing calls, or CO/ PBX ring transfer calls. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 93...
Page 129: Behind Pbx Setup
Document Revision 1 Electra Elite IPK II Program 14 : Trunk, Basic Setup 14-04 : Behind PBX Setup Level: Description Use Program 14-04 : Behind PBX Setup to indicate if the trunk is installed behind a PBX. There is one item for each of the modes.
Page 130: Trunk Group
Input Data Trunk Port Number 001~200 Item Trunk Group Order Number Number 0~100 1~200 Default Trunk Port Group Priority Conditions None Feature Cross Reference Trunk Groups Electra Elite IPK II Programming Manual 2 - 95...
Page 131: Trunk Group Routing
Document Revision 1 Electra Elite IPK II Program 14 : Trunk, Basic Setup 14-06 : Trunk Group Routing Level: Description Use Program 14-06 : Trunk Group Routing to set up an outbound routing table for the trunk groups you assigned in Program 14-05. When users dial 9, the system routes their calls in the order (priority) specified.
Page 132 Route 1, Order Number 1 = 1 (Trunk Group 1). Order Numbers 2, 3, 4 = 0 (Not Specified). All Other Routes (2~100) and Order Numbers (1-4) = 0 (Not Specified). Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 97...
Page 133: Trunk Access Map Setup
Document Revision 1 Electra Elite IPK II Program 14 : Trunk, Basic Setup 14-07 : Trunk Access Map Setup Level: Description Use Program 14-07 : Trunk Access Map Setup to set up the Trunk Access Maps. This sets an extension’s access options for trunks. For example, an extension can only place outgoing calls on trunks to which it has outgoing access.
Page 134 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Central Office Calls, Answering Central Office Calls, Placing Electra Elite IPK II Programming Manual 2 - 99...
Page 135: Music On Hold Source For Trunks
Document Revision 1 Electra Elite IPK II Program 14 : Trunk, Basic Setup 14-08 : Music on Hold Source for Trunks Level: Description Use Program 14-08 : Music on Hold Source for Trunks to define a Music on Hold source for a trunk as either the ACI or COI port.
Page 136: Conversation Recording Destination For Trunks
1 = On Determine if incoming trunk calls should be automatically recorded to the ACI. --- Not Used --- --- Not Used --- Conditions None Feature Cross Reference Analog Communications Interface (ACI) Electra Elite IPK II Programming Manual 2 - 101...
Page 137: Ccis System Route Id
Document Revision 1 Electra Elite IPK II Program 14 : Trunk, Basic Setup 14-13 : CCIS System Route ID Level: Description This program defines the CCIS route ID to the trunk group used for K-CCIS. Input Data Trunk Group Number...
Page 138: Ccis Trunk Cic Assignment
Not Assigned Conditions CIC Numbers must be assigned consecutively for K-CCIS to operate correctly. The D-Channel trunk port should not have a CIC assignment. Feature Cross Reference Key-Common Channel Interoffice Signaling (K-CCIS) Electra Elite IPK II Programming Manual 2 - 103...
Page 139 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 104 Program 14 : Trunk, Basic Setup...
Page 140: Program 15 : Extension, Basic Setup
Line Preference feature for more details. = Do not print on SMDR Printout SMDR report Use this option to include or = Include on exclude the extension in the SMDR report SMDR report. Electra Elite IPK II Programming Manual 2 - 105...
Page 141 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program ISDN Caller ID 0 = Disable 10-03-05 1 = Enable If both Program 15-01-04 and 10-03-05 are enabled, the system includes Caller ID in the Setup message as “Presentation Allowed”.
Page 142: Multiline Telephone Basic Data Setup
= Ring Tone 1 = Ring Tone 2 = Ring Tone 3 = Ring Tone 4 = Ring Tone 5 Electra Elite IPK II Programming Manual 2 - 107...
Page 143 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Extension Ring Tone = High = Medium Use this option to set the tone (pitch) of = Low the incoming extension call ring for the extension port you are programming.
Page 144 (1~2=on, 3~8=off). Baud Rate for CTA Port = 4800 15-02-19 = 9600 Select the baud rate to be used by the = 19200 CTA Adapter. Electra Elite IPK II Programming Manual 2 - 109...
Page 145 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Virtual Extension Access Mode = DSS (when idle Virtual Extension key = Outgoing (OTG) pressed) = Ignore Determine whether a Virtual Extension/ Call Arrival Key(CAR) should function as a DSS key, a Virtual Extension, or a CAR key.
Page 146 = Vir. Ext Vir. Ext Toll Restriction Class (Virtual Extension’s Select the Toll Restriction Class to be Class) used when placing a call from a virtual = Real Ext (Real extension. Extension’s Class) Electra Elite IPK II Programming Manual 2 - 111...
Page 147: Table 2-3 Program 15 : 02 - Incoming Signal Frequency Patterns
Document Revision 1 Electra Elite IPK II Table 2-3 Program 15 : 02 – Incoming Signal Frequency Patterns Incoming Signal Type Frequency 1 Frequency 2 Modulation Frequency Pattern External Incoming Signal High 1100 1400 16Hz Middle 16Hz Frequency (Pattern 1)
Page 148: Single Line Telephone Basic Data Setup
Use this option to tell the system the type of dialing the connected telephone uses. In order for the Electra Elite IPK II Wireless telephones to function correctly, this must be set to ’0’ (dial pulse). If this option is set for DTMF, after an outside call is placed, the system will not dial any additional digits.
Page 149 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program = Disable Extension Polarity Reverse (Off) -- Not Used in U.S. -- = Enable Do Not Change Default Entry as DTMF issues (On) may arise with voice mail.
Page 150 Reverse (1) = Off-Hook (2) = Calling/Ringing (3) = Answer (4) = Detect Hang Up (5) = On-Hook Conditions None Feature Cross Reference Single Line Telephone, Analog Single Line Telephone, Digital Electra Elite IPK II Programming Manual 2 - 115...
Page 151: Ip Telephone Terminal Basic Data Setup
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-05 : IP Telephone Terminal Basic Data Setup Level: Description Use Program 15-05 : IP Telephone Terminal Basic Data Setup to set up the basic settings for an IP telephone.
Page 152: Trunk Access Map For Extensions
Input Data Extension Number Maximum 8 digits Day/Night Mode Item Trunk Access Related Default Map Number Program 1~200 14-07 Conditions None Feature Cross Reference Central Office Calls, Answering Central Office Calls, Placing Electra Elite IPK II Programming Manual 2 - 117...
Page 153: Programmable Function Keys
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-07 : Programmable Function Keys Level: Description Use Program 15-07 : Programmable Function Keys to assign functions to a multiline terminal's line keys. For certain functions, you can append data to the key’s basic function. For example, the function 26 appended by data 1 makes a Group Call Pickup key for Pickup Group 1.
Page 154 Slow Blink (Red): Call Forward - Busy/No Forwarded Answer Slow Blink (Red): Call Forward – Both Ring Forwarded Follow Me Rapid Blink (Red): Forwarded --- Not Used --- --- Not Used --- Electra Elite IPK II Programming Manual 2 - 119...
Page 155 Document Revision 1 Electra Elite IPK II Function Number List (Continued) [1] Normal Function Code (00 – 99) (Service Code 751) Function Function Additional Data LED Indication Number Red On: Text Message Setup Message Numbers (01~20) Feature activated by Function...
Page 156 Extension Name Change None Blink (Red): General Purpose LED Active Operation General Purpose LED Blink (Red): Active Indication Blink (Red): Automatic Transfer at Extension Group Number Active Department Group Call (1~8 or 01~64) Electra Elite IPK II Programming Manual 2 - 121...
Page 157 Document Revision 1 Electra Elite IPK II Function Number List (Continued) [1] Normal Function Code (00 – 99) (Service Code 751) Function Function Additional Data LED Indication Number Blink (Red): Delayed Transfer at Extension Group Number Active Department Group Call...
Page 158 4 = Urgent Page Drop Key Directory Dialing Private Call Refuse Caller ID Refuse Dial-In Mode Switching 22-17 Do-Not-Call Setup Do-Not-Call Data Registration Live Recording Key In-Mail --- Not Used --- Electra Elite IPK II Programming Manual 2 - 123...
Page 159 Document Revision 1 Electra Elite IPK II Function Number List [2] Appearance Function Level (*00 - *99) (Service Code 752) Function Function Additional Data LED Indication Number --- Not Used --- Red On: Trunk Key Trunk Number (1~8 or Trunk Busy by Another User...
Page 160 Red On: Under Work Time Slow Blink (Red): Under Reservation Red On: ACD Overflow Control ACD Group Number Enable Slow Blink (Red): Disable ACD Queue Status Display Check --- Not Used --- Electra Elite IPK II Programming Manual 2 - 125...
Page 161 Document Revision 1 Electra Elite IPK II LED Indication Reference: ON = LED pattern 7 (On). OFF = LED pattern 0 (Off). Rapid Blink = LED pattern 3 (RW). Slow Blink (General Function Level) = LED pattern 5 (IL). Slow Blink (Appearance Function Level) = LED pattern 1 (FL).
Page 162 When assigning a CAP key, 0 8, an orbit number must be used. If orbit 000 is used, it will automatically assign the next available orbit. Feature Cross Reference Refer to Function Number List. Electra Elite IPK II Programming Manual 2 - 127...
Page 163: Incoming Virtual Extension Ring Tone Setup
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-08 : Incoming Virtual Extension Ring Tone Setup Level: Description Use Program 15-08 : Incoming Virtual Extension Ring Tone Setup to assign a ring tone range (0~4) to incoming virtual extensions assigned to a Virtual Extension key (Program 15-07).
Page 164: Table 2-4 Program 15 : 08 - Incoming Signal Frequency Patterns
Pattern 4 High 1100 1100 No modulation Middle No modulation No modulation Internal Incoming Signal High 1100 1400 Frequency Middle Conditions None Feature Cross Reference Multiple Directory Number / Call Coverage Electra Elite IPK II Programming Manual 2 - 129...
Page 165: Virtual Extension Ring Assignment
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-09 : Virtual Extension Ring Assignment Level: Description Use Program 15-09 : Virtual Extension Ring Assignment to assign the ringing options for an extension’s Virtual Extension Key or Virtual Extension Group Answer Key which is defined in Program 15-07.
Page 166: Incoming Virtual Extension Ring Tone Order Setup
= Incoming Extension the priority of ring sound is set up. Ring Tone Default By default, Virtual Extension ring tones have the following order. Ring Tone Order (Set in Program 15-08) Electra Elite IPK II Programming Manual 2 - 131...
Page 167 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Multiple Directory Number / Call Coverage 2 - 132 Program 15 : Extension, Basic Setup...
Page 168: Virtual Extension Delayed Ring Assignment
20-04-03 Ring = Delayed Ring Conditions Program the Virtual Extension keys NOT to ring before removing the key from a keyset’s programming. Feature Cross Reference Multiple Directory Number / Call Coverage Electra Elite IPK II Programming Manual 2 - 133...
Page 169: Conversation Recording Destination For Extensions
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-12 : Conversation Recording Destination for Extensions Level: Description Use Program 15-12 : Conversation Recording Destination for Extensions to set the ACI Conversation Recording destination for each extension.
Page 170: Programmable One-Touch Keys
Use Program 15-14 : Programmable One-Touch Keys to define the One-Touch key data for each multiline terminal. For each Electra Elite IPK II Wireless telephone to use the Transfer When Out of Range feature, enter the destination number (up to 24 digits) and name (up to 12 characters) into One-Touch bin 10.
Page 171: Wireless Dect Terminal Basic Data Setup
15-15 : Wireless DECT Terminal Basic Data Setup Level: Description Use Program 15-15 : Wireless DECT Terminal Basic Data Setup to define the options for the Electra Elite IPK II Wireless telephones. Input Data Extension Number Maximum 8 digits Item...
Page 172 Default Program Terminal Capability This program is read only. This program displays the capability of the Electra Elite IPK II Wireless DECT telephone displaying the options below. This program is read only. Display Capabilities ISDN Support Tone Capabilities Data Services Profile E Class 2...
Page 173 Model Identifier This program is read only. This program shows the model identifier that the Electra Elite IPK II Wireless DECT terminal uses. The model identifier contains the following items: Manufacturer Identification Code (MANIC) and Model Identification Code (MODIC). This program is read only.
Page 174: Co Message Waiting Indication
Extension Number including Virtual Extensions Up to 8 digits Trunk Port Number 001~200 Item Item Input Data Default LED Flash Assignment 0 = LED Off 1 = LED On Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 139...
Page 175: Virtual Extension Key Enhanced Options
Document Revision 1 Electra Elite IPK II Program 15 : Extension, Basic Setup 15-18 : Virtual Extension Key Enhanced Options Level: Description Use Program 15-18 : Virtual Extension Key Enhanced Options to define the operation when a Virtual Extension Key is pressed.
Page 176: Lcd Line Key Name Assignment
Key Number 01~16 (for 16LD TEL) 17~32 (for 16LD ADM) Default Settings Line Key Name LK01 CO001 LK08 CO008 LK09 All Blank LK32 All Blank Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 141...
Page 177 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 142 Program 15 : Extension, Basic Setup...
Page 178: Program 16 : Department Group Setup
This only member routes to occurs for calls to the extension idle member) directly, not the department number assigned in Program 11-07. Electra Elite IPK II Programming Manual 2 - 143...
Page 179 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Program Hunting Mode = Last extension is called and hunting Use this option to set the action is stopped taken when a call reaches the = Circular...
Page 180 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Department Calling Electra Elite IPK II Programming Manual 2 - 145...
Page 181: Department Group Assignment For Extensions
Document Revision 1 Electra Elite IPK II Program 16 : Department Group Setup 16-02 : Department Group Assignment for Extensions Level: Description Use Program 16-02 : Department Group Assignment for Extensions to set the Department Groups. The system uses these groups (64 Department Groups) for Department Calling.
Page 182: Secondary Department Group
Maximum 8 0~999 This program is set up when placing digits telephones into two or more groups. Default All extension groups : No setting Conditions None Feature Cross Reference Department Calling Electra Elite IPK II Programming Manual 2 - 147...
Page 183 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 148 Program 16 : Department Group Setup...
Page 184: Program 20 : System Option Setup
Callback or Trunk Queueing request Time after this interval. Trunk Guard Timer 0~64800 seconds 1~86400 seconds Web Logout Time The system automatically logs out a Web Pro session after inactivity lasting this interval. Electra Elite IPK II Programming Manual 2 - 149...
Page 185 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Refer to the Input Data table at the beginning of this section. 2 - 150 Program 20 : System Option Setup...
Page 186: System Options For Multiline Telephones
Set the conditions under which a headset extension is busy to incoming callers. Preselection Time 0~64800 seconds When a multiline terminal user preselects a line key, the system remembers the preselection for this interval. Electra Elite IPK II Programming Manual 2 - 151...
Page 187 Document Revision 1 Electra Elite IPK II Input Data (Continued) Item Related Item Input Data Default Programming Time and Date Display Mode Set how the Time and Date appear on Type 1: (12 hour) 10 MAR TUE 3:15PM display telephones. There are eight Type 2: (12 hour) 3:15PM MAR 10 TUE display modes.
Page 188 Document Revision 1 Input Data (Continued) Item Related Item Input Data Default Programming Caller ID Display Mode 0= Name and Number (Both) 1= Name 2= Number Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 153...
Page 189: System Options For Single Line Telephones
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-03 : System Options for Single Line Telephones Level: Description Use Program 20-03 : System Options for Single Line Telephones to set up various options for single line telephones.
Page 190 Trunk call dial forced sending start time 0~64800 seconds 20-03-03 (Forced Dial) 20-03-04 Conditions None Feature Cross Reference Single Line Telephones, Analog Single Line Telephones, Digital Electra Elite IPK II Programming Manual 2 - 155...
Page 191: System Options For Virtual Extensions
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-04 : System Options for Virtual Extensions Level: Description Use Program 20-04 : System Options for Virtual Extensions to set up various system options for Virtual Extensions. There are 256 available virtual extension ports.
Page 192: Class Of Service For Extensions
Class of Service Mode for Extensions 1~15 Default Extension number 101 as Class 15. All other extension numbers are set as Class 1. Conditions None Feature Cross Reference Class of Service Electra Elite IPK II Programming Manual 2 - 157...
Page 193: Class Of Service Options (Administrator Level)
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-07 : Class of Service Options (Administrator Level) Level: Description Use Program to define the 20-07 : Class of Service Options (Administrator Level) administrator service availability for each extension’s Class of Service (COS).
Page 194 1 = On --- Not Used --- CO MSG Waiting Indication Callback 0 = Off Number Programming 1 = On Enable or Disable an extension’s ability to receive CO Message Waiting Indication. Electra Elite IPK II Programming Manual 2 - 159...
Page 195 Document Revision 1 Electra Elite IPK II Default Item Input Related Item Data Program COS 15 1~14 Set/Cancel Private Call Refuse 0 = Off 11-10-32 1 = On Enable or Disable an extension’s ability to set or cancel Private Call Refuse.
Page 196: Class Of Service Options (Outgoing Call Service)
1 = On Turns off or on an extension to use Repeat Redial. Toll Restriction Dial Block 0 = Off 1 = On Turns off or on an extension to use Dial Block. Electra Elite IPK II Programming Manual 2 - 161...
Page 197 Document Revision 1 Electra Elite IPK II Default Item Input Related Item Data Program 01-14 Hotline/Extension Ringdown 0 = Off 1 = On Turns off or on Ringdown Extension for extensions with this COS. Signal/Voice Call 0 = Off Turns off or on an extension allowing it to force...
Page 198 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Class of Service Electra Elite IPK II Programming Manual 2 - 163...
Page 199: Class Of Service Options (Incoming Call Service)
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-09 : Class of Service Options (Incoming Call Service) Level: Description Use Program 20-09 : Class of Service Options (Incoming Call Service) to define the incoming call feature availability for each extension Class of Service (COS).
Page 200 Calling Party Information 0 = Off 50-02-05 Turn off or on an extension’s ability to display 1 = On calling party information on CCIS calls. Conditions None Feature Cross Reference Class of Service Electra Elite IPK II Programming Manual 2 - 165...
Page 201: Class Of Service Options (Answer Service)
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-10 : Class of Service Options (Answer Service) Level: Description Use Program 20-10 : Class of Service Options (Answer Service) to define the answer feature availability for each extension Class of Service (COS).
Page 202 Turn off or on an extension’s ability to use Call Pickup to 1 = On pick up Callback calls. Answer Preset 0 = Off 1 = On Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 167...
Page 203: Class Of Service Options (Hold/Transfer Service)
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-11 : Class of Service Options (Hold/Transfer Service) Level: Description Use Program 20-11 : Class of Service Options (Hold/Transfer Service) to define the Hold and Transfer feature availability for each extension Class of Service (COS).
Page 204 Allow (0) or deny (1) answered transferred calls from 1 = On recalling the originating extension. Hold/Extended Park 0 = Off Determine if an extension’s Class of Service should 1 = On allow either a normal or extended Park. Electra Elite IPK II Programming Manual 2 - 169...
Page 205 Document Revision 1 Electra Elite IPK II Default Item Item Input Data 01~14 No Callback 0 = Off 1 = On Turns off or on an extension to receive callbacks. Restriction for Tandem Trunking on Hang Up 0 = Off Allow (0) or deny (1) an extension user’s ability to set...
Page 206: Class Of Service Options (Charging Cost Service)
--- Not Used --- Advice of Charge 0 = Off 1 = On ISDN-AOC Cost Display (TTU) 0 = Off 1 = On Conditions None Feature Cross Reference Class of Service Electra Elite IPK II Programming Manual 2 - 171...
Page 207: Class Of Service Options (Supplementary Service)
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-13 : Class of Service Options (Supplementary Service) Level: Description Use Program 20-13 : Class of Service Options (Supplementary Service) to define the supplementary feature availability for each extension Class of Service (COS).
Page 208 0 = Off Turns off or on an extension’s ability to program 1 = On General function keys using Service Code 751 (by default). (Refer to Program 20-07-10 for Service Code 752.) Electra Elite IPK II Programming Manual 2 - 173...
Page 209 Document Revision 1 Electra Elite IPK II Default Item Related Item Input Data Programming 01~14 Selectable Display Messaging (Text Messaging) 0 = Off Turns off or on an extension’s ability to use Selectable 1 = On Display Messaging. Account Code/Toll Restriction Operator Alert...
Page 210 Turn off or on an extension's ability to use Extension 1 = On Data Swap. --- Not Used --- Live Monitor Enabling 0 = Off 1 = On Turn off or on an extension’s ability to use Live Monitor. Electra Elite IPK II Programming Manual 2 - 175...
Page 211 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Class of Service 2 - 176 Program 20 : System Option Setup...
Page 212: Class Of Service Options For Disa/E&M
System Speed Dialing. Operator Calling 0 = Off 1 = On This option enables or disables a DISA or tie trunk caller’s ability to dial 0 for the telephone system operator. Electra Elite IPK II Programming Manual 2 - 177...
Page 213 Document Revision 1 Electra Elite IPK II Default Item Input Item Data 01~14 Internal Paging 0 = Off 1 = On This option enables or disables a DISA or tie trunk caller’s ability to use the telephone system’s Internal Paging.
Page 214: Ring Cycle Setup
Virtual Extension Ring Callback Alarm for SLT VRS Waiting Message Incoming Call Table 2-5 Ringing Cycles Number Ringing Cycle On:2.0 / Off:4.0 On:1.0 / Off:2.0 On:0.5 / Off:0.5 On:0.25 / Off:0.25 Electra Elite IPK II Programming Manual 2 - 179...
Page 215 Document Revision 1 Electra Elite IPK II Table 2-5 Ringing Cycles (Continued) Number Ringing Cycle On:0.5 / Off:0.5 / On:0.5 / Off:1.5 On:0.25 / Off:0.25 / On:0.25 / Off:5.25 On:0.375 / Off:0.25 / On:0.375 / Off:2.0 On:0.25 / Off:0.125 / On:0.25 / Off:0.125 / On:0.25 / Off:2.0 On:1.0 / Off:4.0...
Page 216: Selectable Display Messages
CONF Clear the character entry one character at a time. HOLD Clear all the entries from the point of the flashing cursor and to the right. Electra Elite IPK II Programming Manual 2 - 181...
Page 217 Document Revision 1 Electra Elite IPK II When using DTP or DTU style telephones on the Electra Elite IPK II system, not all the same characters are available. Input Data Selectable Display Message Number 01~20 Item Text Data 24 characters...
Page 218 Electra Elite IPK II Document Revision 1 Conditions Time value "## : ##" must be followed by two spaces. Feature Cross Reference Selectable Display Messages Electra Elite IPK II Programming Manual 2 - 183...
Page 219: Operator's Extension
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-17 : Operator’s Extension Level: Description Use Program 20-17 : Operator’s Extension to designate an operator. When an extension user dials “0” or “9” (defined by Program 11-01 Type 5), calls go to the operator selected in this program.
Page 220: Service Tone Timers
Over, etc), the system repeats the Intrusion Tone after this interval. Normally, you should enter 0 to disable this interval. Conference Tone 0~64800 Interval seconds Warning Beep Tone 0~64800 14-01-18 Signaling Interval seconds Electra Elite IPK II Programming Manual 2 - 185...
Page 221 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Distinctive Ringing, Tones, and Flash Patterns 2 - 186 Program 20 : System Option Setup...
Page 222: System Options For Caller Id
This timer is used with ISDN trunks to determine how long the system will wait for the Caller ID name from the Telco. Caller ID Sender Queing Time (Sender Wait) 0~64800 seconds Conditions None Feature Cross Reference Caller ID Electra Elite IPK II Programming Manual 2 - 187...
Page 223: Message Setup For Non-Caller Id Data
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-20 : Message Setup for Non-Caller ID Data Level: Description Use Program 20-20 : Message Setup for Non-Caller ID Data to define the messages which will be displayed when no Caller ID information is received.
Page 224: System Options For Long Conversation
Long Conversation Cutoff for Outgoing Call 0~64800 (sec) 14-01-14 This timer determines how long the system will wait before disconnecting an outgoing call. Conditions None Feature Cross Reference Long Conversation Cutoff Electra Elite IPK II Programming Manual 2 - 189...
Page 225: System Options For Wireless Dect Service
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-22 : System Options for Wireless DECT Service Level: Description Use Program 20-22 : System Options for Wireless DECT Service to define the time the system waits before determining the Wireless DECT (DECT) phone is out of range.
Page 226: System Options For Cti
Enable or disable the system to send trunk or virtual (Yes) extension information to the TSP driver. The Timer that waits for an off-hook for Single Line 0~64800 (sec) Telephone Conditions None Feature Cross Reference Computer Telephony Integration (CTI) Applications Electra Elite IPK II Programming Manual 2 - 191...
Page 227: Isdn Options
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-25 : ISDN Options Level: Description Use Program 20-25 : ISDN Options to define the ISDN system options. Input Data Item Item Input Data Default Send the Release Message After Subscriber Hangs...
Page 228 Busy tone send when T-point receiving a RELEASE message from Network. No Response Release Send 0 = Off 1 = On Operation mode setting for when second T303 timer is expired. Conditions None Feature Cross Reference ISDN Compatibility Electra Elite IPK II Programming Manual 2 - 193...
Page 229: Multiplier Changing Co
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-26 : Multiplier Changing CO Level: Description Use Program 20-26 : Multiplier Changing CO to define the Multiplier for charging cost to each extension service class. Input Data...
Page 230: Trunk To Trunk Conversation
25-07-07 25-07-08 Conversation Disconnect Code 0~9, #, No Setting 14-01-25 24-02-07 24-02-10 25-07-07 25-07-08 Conversation Continue Time 0~64800 seconds 14-01-25 20-28-01 24-02-07 24-02-10 25-07-07 25-07-08 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 195...
Page 231: Timer Class For Extension
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-29 : Timer Class for Extension Level: Description Use Program 20-29 : Timer Class for Extension to assign the timer class to each extension. There are 16 Classes that can be assigned. You make eight entries for this Program, one for each Night Service Mode.
Page 232: Timer Class For Trunks
Night Service Mode. The details of classes are assigned by PRG 20-3. Input Data Item Related Item Input Data Default Programming 0~15, #, Day/Night Mode 1~8, Class Number 0 = Not assigned Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 197...
Page 233: Timer Class Timer Assignment
Document Revision 1 Electra Elite IPK II Program 20 : System Option Setup 20-31 : Timer Class Timer Assignment Level: Description Use Program 20-31 : Timer Class Timer Assignment to assign values to the timers on a class of service basis.
Page 234 16 in 20-29-01 or 20-30-01. When the timer class is set to 0, the system-wide timer is used. All defaults are the same as the system wide timers. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 199...
Page 235 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 200 Program 20 : System Option Setup...
Page 236: Program 21 : Outgoing Call Setup
Dial Pause at First Digit 0~64800 (sec) 0~64800 (sec) Toll Restriction Override Time 20-08-06 21-07 After dialing the Toll Restriction Override codes, the system removes Toll Restriction from the extension for this interval. Electra Elite IPK II Programming Manual 2 - 201...
Page 237 Document Revision 1 Electra Elite IPK II Input Data Item Related Item Input Data Default Program 0~64800 (sec) Preset Dial Display Hold Time Ringdown Extension Timer (Hotline 20-08-09 0~64800 (sec) Start) 21-11 A Ringdown extension automatically calls its programmed destination after this interval.
Page 238 0 = Disable (Off) 99-01-01 Access 1 = Enable (On) Do Not Call 0 = No Service 15-01-07 (Off) 1 = Extended Common Restriction (On) Conditions None Feature Cross Reference Central Office Calls, Placing Electra Elite IPK II Programming Manual 2 - 203...
Page 239: Trunk Group Routing For Extensions
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-02 : Trunk Group Routing for Extensions Level: Description Use Program 21-02 : Trunk Group Routing for Extensions to assign Program 14-06 routes to extensions. Input Data...
Page 240: Trunk Group Routing For Trunks
Automatic External Call Forward. The Route Table is set in Program 14-06. Input Data Trunk Port Number 001~200 Item Day/Night Route Table Related Default Mode Number Program 0~100 14-06 (0 = No setting) 14-07-01 Conditions None Feature Cross Reference Trunk Group Routing Electra Elite IPK II Programming Manual 2 - 205...
Page 241: Toll Restriction Class For Extensions
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-04 : Toll Restriction Class for Extensions Level: Description Use Program 21-04 : Toll Restriction Class to assign a Toll Restriction class to an extension. The details of Toll Restriction are defined in Program 21-05 and 21-06.
Page 242: Toll Restriction Class
21-06-05 is referred to, or = Assigned not referred to. (Yes) Permit Code Table 1~4 = Table Set the tables 1~4 when referring 21-06-06 = Disable to the table set up by 21-06-06. (None) Electra Elite IPK II Programming Manual 2 - 207...
Page 243 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Description Program Restriction Table 1~4 = Table Set the tables 1~4 when referring 21-06-07 = Disable to the table set up by 21-06-07. (None) Restriction for = Does Not...
Page 244 Class No. 2 Class No. 3 Class No. 4 Class No. 5 Class No. 6 Class No. 7 Class No. 8 Class No. 15 Conditions None Feature Cross Reference Toll Restriction Electra Elite IPK II Programming Manual 2 - 209...
Page 245: Toll Restriction Table Data Setup
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-06 : Toll Restriction Table Data Setup Level: Description to set the system Toll Restriction Program 21-06 : Toll Restriction Table Data Setup data. Dial 1-9, 0, , # can be entered in each table.
Page 246 Access Codes. Each code can have up to 2 digits. Specific Dial Dial No Setting Outgoing Code (Up to 8 digits) Outgoing Call Dial No Setting Code Setup (Up to 4 digits) Electra Elite IPK II Programming Manual 2 - 211...
Page 247 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Toll Restriction 2 - 212 Program 21 : Outgoing Call Setup...
Page 248: Toll Restriction Override Password Setup
Input Data Extension Number Maximum 8 digits Item Related Password Default Program 4 Digits (Fixed) No Setting 21-01-07 20-08-06 Conditions None Feature Cross Reference Toll Restriction Override Electra Elite IPK II Programming Manual 2 - 213...
Page 249: Repeat Dial Setup
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-08 : Repeat Dial Setup Level: Description Use Program 21-08 : Repeat Dial Setup to define the automatic Repeat Dial data. Input Data Item Related Item Input Data...
Page 250: Dial Block Setup
If Dial Block is available for all Classes of Service, everyone may become a supervisor if they know the Dial Block password. Feature Cross Reference Toll Restriction Electra Elite IPK II Programming Manual 2 - 215...
Page 251: Dial Block Restriction Class Per Extensions
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-10 : Dial Block Restriction Class Per Extensions Level: Description Use Program 21-10 : Dial Block Restriction Class Per Extensions to define the Toll Restriction Class to each extension when the extension is set for Dial Block Restriction.
Page 252: Extension Ringdown (Hotline) Assignment
Hotline Destination Number Default Program , #, Pause, Hook Flash, No Setting 20-08-09 @ (Code to wait for a response) 21-01-09 (maximum 24 digits) Conditions None Feature Cross Reference Ringdown Extension Electra Elite IPK II Programming Manual 2 - 217...
Page 253: Isdn Calling Party Number Setup For Trunks
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-12 : ISDN Calling Party Number Setup for Trunks Level: Description Use Program 21-12 : ISDN Calling Party Number Setup for Trunks to assign Calling Party Numbers for each trunk (maximum 16 digits per entry). When a call is...
Page 254: Isdn Calling Party Number Setup For Extensions
Program 21-13. Input Data Extension Number Maximum 8 digits Item Calling Party Default Number Data 0~9, No setting (Max. 16 digits) Conditions None Feature Cross Reference ISDN Compatibility Electra Elite IPK II Programming Manual 2 - 219...
Page 255: Walking Toll Restriction Password Setup
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-14 : Walking Toll Restriction Password Setup Level: Description Use Program 21-14 : Walking Toll Restriction Password Setup to assign the password and Toll Restriction Class for Walking Toll Restriction. Each code is six...
Page 256: Individual Trunk Group Routing For Extensions
When entering data for this option, enter the route number or “0” to prevent routing. Input Data Extension Number Maximum 8 digits Item Day/Night Route Table Default Mode Number 0~100 (0 = No Setting) Conditions None Feature Cross Reference Central Office Calls, Placing Electra Elite IPK II Programming Manual 2 - 221...
Page 257: Toll Restriction For Trunks (Seized Trunk Basis Setting)
Document Revision 1 Electra Elite IPK II Program 21 : Outgoing Call Setup 21-21 : Toll Restriction for Trunks (Seized Trunk Basis Setting) Level: Description Use Program 21-21 : Toll Restriction for Trunks (Seized Trunk Basis Setting) to define the toll restriction class to each trunk. The details of toll restriction are defined by PRG 21-05 and 21-06.
Page 258: Co Message Waiting Indication - Call Back Settings
Enable or Disable CO MWI Call Back. 1=Enable VMWI Service CO-MWI Call Back Number Area Setting 0000~1999 1999 Define the Speed Dial Bin number for MWI Call Back. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 223...
Page 259 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 224 Program 21 : Outgoing Call Setup...
Page 260: Program 22 : Incoming Call Setup
Intercept, this interval sets the Ring-No- Answer time. This interval is how long a DID call rings the destination extension before rerouting to the intercept ring group. DID Incoming 0~64800 (sec.) Ring Group no answer timer Electra Elite IPK II Programming Manual 2 - 225...
Page 261 Document Revision 1 Electra Elite IPK II Input Data Item Related Item Input Data Default Description Program DID Pilot Call No 0~64800 (sec.) answer timer 0~64800 (sec.) DID to Trunk to Trunk no answer timer VRS Waiting = Enable This program sets up the operation...
Page 262: Incoming Call Trunk Setup
When the trunk type is set to a 3 (DID), the DID Transfert Destination in 22-11-04 for each DID feature is not supported. This feature is only supported for DID trunks when assigned as VRS. Feature Cross Reference Central Office Calls, Answering Electra Elite IPK II Programming Manual 2 - 227...
Page 263: Trunk Ring Tone Range
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-03 : Trunk Ring Tone Range Level: Description Use Program 22-03 : Trunk Ring Tone Range to select the ring tone range for the trunk. The trunk uses a ring tone within the range selected when it rings an extension.
Page 264 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Selectable Ring Tones Electra Elite IPK II Programming Manual 2 - 229...
Page 265: Incoming Extension Ring Group Assignment
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-04 : Incoming Extension Ring Group Assignment Level: Description Use Program 22-04 : Incoming Extension Ring Group Assignment to assign extensions to Ring Groups. Calls ring extensions according to Ring Group programming.
Page 266: Incoming Trunk Ring Group Assignment
1~8 or 001~100 Incoming Ring Groups (Incoming Group) (22-04). 101 (DSPII-U10 Internal Voice Mail on Compact Flash) 102 (In-Skin/ External Voice Mail) 103 (Not used) Conditions None Feature Cross Reference Ring Groups Electra Elite IPK II Programming Manual 2 - 231...
Page 267: Normal Incoming Ring Mode
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-06 : Normal Incoming Ring Mode Level: Description Use Program 22-06 : Normal Incoming Ring Mode to define whether or not an extension should ring for the Normal Incoming Ring Mode.
Page 268: Dil Assignment
Number of Transferring Default Mode Destination Extension Number (maximum 8 No Setting digits) Pilot Number Conditions Program 22-02 must be set to ‘4’ for the trunk. Feature Cross Reference Direct Inward Line (DIL) Electra Elite IPK II Programming Manual 2 - 233...
Page 269: Dil/Irg No Answer Destination
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-08 : DIL/IRG No Answer Destination Level: Description For DIL Delayed Ringing, use Program 22-08 : DIL/IRG No Answer Destination to assign the DIL No Answer Ring Group. An unanswered DIL rings this group after the DIL No Answer Time expires (Program 22-01-04).
Page 270: Did Basic Data Setup
Dial (1 digit: 0~9) No Setting (Only Overlap Receiving Mode) T302 Time-out Operation = Disconnect (Cut) = Transfer (Refer to (Only Overlap Receiving Mode) Program 22-12 : DID Intercept Ring Group on page 2-243.) Electra Elite IPK II Programming Manual 2 - 235...
Page 271 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Direct Inward Dialing (DID) 2 - 236 Program 22 : Incoming Call Setup...
Page 272: Did Translation Table Setup
1st Area Setup (End Address) See below 2nd Area Setup (Start Address) See below 2nd Area Setup (End Address) See below Default Conversion Table Area Start Start Table Table Table Table Electra Elite IPK II Programming Manual 2 - 237...
Page 273 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Direct Inward Dialing (DID) 2 - 238 Program 22 : Incoming Call Setup...
Page 274: Did Translation Number Conversion
Enter characters A-C, a-c, 2. Enter characters D-F, d-f, 3. Enter characters G-I, g-i, 4. Enter characters J-L, j-l, 5. Enter characters M-O, m-o, 6. Enter characters P-S, p-s, 7. Enter characters T-V, t-v, 8. Electra Elite IPK II Programming Manual 2 - 239...
Page 275 Document Revision 1 Electra Elite IPK II Key for Entering Names When entering names in the procedures below, refer to this chart. Names can be up to 12 digits long. Use this keypad digit . . . When you want to. . .
Page 276 Translation Number Conversion, Transfer Destination Number 2 are set, the priority of transferring will be in this order: Program 22-11-05 then Program 22-11-06 then if Program 22-11-11 is enabled, Program 22-12-01. Electra Elite IPK II Programming Manual 2 - 241...
Page 277 Document Revision 1 Electra Elite IPK II Conditions When the trunk type is set to a 3 (DID) in 22-02-01, the DID Transfer Destination for each DID feature is not supported. This feature is only supported for DID trunks when assigned as VRS.
Page 278: Did Intercept Ring Group
Conversion Table Area Number 01~20 Item Day/Night Incoming Group Number Default Mode 0 (No Setting) 1~8 or 1~100 (Incoming Group) 101 (DSPII-U10 Voice Mail) 102 (In-Skin/External Voice Mail) 103 (Centralized Voice Mail) Electra Elite IPK II Programming Manual 2 - 243...
Page 279 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Direct Inward Dialing (DID) 2 - 244 Program 22 : Incoming Call Setup...
Page 280: Did Trunk Group To Translation Table Assignment
For each Trunk Group, you make a Translation Table entry for each Night Service mode. Input Data Trunk Group Number 1~100 Item Conversion Table Day/Night Mode Default Area Number 0~20 (0 = No Setting) Conditions None Feature Cross Reference Direct Inward Dialing (DID) Electra Elite IPK II Programming Manual 2 - 245...
Page 281: Vrs Delayed Message For Irg
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-14 : VRS Delayed Message for IRG Level: Description Use Program 22-14 : VRS Delayed Message for IRG (Incoming Group Ring) to define for each incoming ring group the timers, VRS message number and type of tone for VRS Waiting Message.
Page 282: Vrs Waiting Message For Department Group
0 = Ring Back Tone 1 = MOH Tone 2 = BGM Source Disconnect Time After the End of 0 = No Disconnect VRS Waiting Message 1~64800 (sec) Conditions None Feature Cross Reference Department Group Electra Elite IPK II Programming Manual 2 - 247...
Page 283: Private Call Refuse Target Area Setup
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-16 : Private Call Refuse Target Area Setup Level: Description Use Program 22-16: Private Call Refuse Target Area Setup to define Speed Dial group number for Private Call Refuse.
Page 284: Dial-In Conversion Table Area Setup For Time Pattern
Up to 8 digits No Setting Received Dial Start of Time 0000~2359 0000 (Time) End of Time 0000~2359 0000 (Time) Dial-In Conversion Table 0~2000 Number Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 249...
Page 285: Private Call Assignment Setup
Document Revision 1 Electra Elite IPK II Program 22 : Incoming Call Setup 22-18 : Private Call Assignment Setup Level: Description Use Program 22-18: Private Call Assignment Setup to define assignment and incoming ring pattern for Private Calls. Item Item...
Page 286: Program 23 : Answer Features Setup
Use this program to assign extensions to 11-12-26 11-12-27 Call Pickup Groups other than the 11-12-28 extension group set up by a Program 15-07-24 16-02. 15-07-25 15-07-26 Conditions None Feature Cross Reference Group Call Pickup Electra Elite IPK II Programming Manual 2 - 251...
Page 287: Universal Answer/Auto Answer
(defined in Program 14-06). The extension user’s own ringing calls, however, always have priority over calls ringing other co-worker’s extensions. Refer to the Line Preference feature in the Electra Elite Electra Elite IPK II Features and Specifications Manual for more information.
Page 288 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Line Preference Night Service Electra Elite IPK II Programming Manual 2 - 253...
Page 289: Ringing Line Preference For Virtual Extensions
Document Revision 1 Electra Elite IPK II Program 23 : Answer Features Setup 23-04 : Ringing Line Preference for Virtual Extensions Level: Description Use Program 23-04 : Ringing Line Preference for Virtual Extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone.
Page 290: Program 24 : Hold/Transfer Setup
System Hold. Forced Release of Held Call 0~64800 (sec) 1800 14-01-16 Depending on the setting of Program 14-01-16, the system disconnects calls on Hold longer than this interval. Electra Elite IPK II Programming Manual 2 - 255...
Page 291 Document Revision 1 Electra Elite IPK II Input Data Item Related Item Input Data Default Program Park Hold Time - Normal 0~64800 (sec) 20-11-19 A call left parked longer than this interval recalls the extension that initially parked Park Hold Time - Extended (Recall)
Page 292: System Options For Transfer
Message Wait Ring Interval Timer 0~64800 (sec) For SLTs without message waiting lamps, this timer determines the amount of time between intermittent ringing. If this timer is set to '0' then the system rings once. Electra Elite IPK II Programming Manual 2 - 257...
Page 293 Document Revision 1 Electra Elite IPK II Input Data Trunk-to-Trunk Transfer Release Warning 0~64800 (sec) 1800 14-01-25 Tone 20-28-01 20-28-02 This timer will start when a trunk begins talking 20-28-03 with another trunk (for example: trunk-to-trunk 24-02-10 transfer, outgoing from trunk, Tandem Trunking).
Page 294: Park Group
Park Group Related Default Description Number Program 1~64 Assign an extension to a Park Group. The 15-07-01 system allows a total of 64 Park Groups. Conditions None Feature Cross Reference Park Electra Elite IPK II Programming Manual 2 - 259...
Page 295: Automatic Trunk-To-Trunk Transfer Target Setup
Document Revision 1 Electra Elite IPK II Program 24 : Hold/Transfer Setup 24-04 : Automatic Trunk-to-Trunk Transfer Target Setup Level: Description Use Program 24-04 : Automatic Trunk-to-Trunk Transfer Target Setup to assign the Speed Dialing number bin which should be used as the destination of the Automatic Trunk-to-Trunk Transfer.
Page 296: Department Group Transfer Target Setup
The Speed Dialing area is used to 11-11-27 13-04 program the destination number of the 24-04 transferred telephone number when a Department Group’s call is transferred using the Trunk-to-Trunk Forwarding feature. Conditions None Feature Cross Reference Transfer Electra Elite IPK II Programming Manual 2 - 261...
Page 297: Call Forward Split Settings
Document Revision 1 Electra Elite IPK II Program 24 : Hold/Transfer Setup 24-09 : Call Forward Split Settings Level: Description Use Program 24-09 : Call Forward Split Settings to assign Call Forwarding Type and the destination numbers for each extension/virtual extension. The destination can be up to 24 digits long, using 0~9, , # and P (pause).
Page 298 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Call Forwarding, Off-Premise Electra Elite IPK II Programming Manual 2 - 263...
Page 299 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 264 Program 24 : Hold/Transfer Setup...
Page 300: Program 25 : Did/Disa Setup
= Use Dial Conversion Table DISA User ID = Off 25-08 = On = Normal (Off) VRS/DISA Transfer Alarm = Alarm (On) Conditions None Feature Cross Reference Direct Inward System Access (DISA) Electra Elite IPK II Programming Manual 2 - 265...
Page 301: Did/Disa Vrs Message
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-02 : DID/DISA VRS Message Level: Description Use Program 25-02 : DID/DISA VRS Message to assign the VRS message number to be used as the Automated Attendant Message for each trunk which is assigned as a VRS/DISA.
Page 302: Vrs/Disa Transfer Ring Group With Incorrect Dialing
1~8 or 1~100 (Incoming Group) 101 (DSPII-U10 Internal Voice Mail on Compact Flash) 102 (In-Skin/External Voice Mail) 103 (Centralized Voice Mail) Conditions None Feature Cross Reference Direct Inward System Access (DISA) Electra Elite IPK II Programming Manual 2 - 267...
Page 303: Vrs/Disa Transfer Ring Group With No Answer/Busy
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-04 : VRS/DISA Transfer Ring Group With No Answer/Busy Level: Description Use Program 25-04 : VRS/DISA Transfer Ring Group With No Answer/Busy to set the operating mode of each DISA trunk. This sets what happens to the call when the DISA or Automated Attendant caller calls a busy or unanswered extension.
Page 304: Vrs/Disa Error Message Assignment
For each trunk, you make a separate entry for each Night Service mode. Input Data Trunk Port Number 001~200 Item Day/Night VRS Message Number Default Mode 0~48 (0 = No Setting) Conditions None Feature Cross Reference Direct Inward System Access (DISA) Electra Elite IPK II Programming Manual 2 - 269...
Page 305: Vrs/Disa One-Digit Code Attendant Setup
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-06 : VRS/DISA One-Digit Code Attendant Setup Level: Description Use Program 25-06 : VRS/DISA One-Digit Code Attendant Setup to set up single digit dialing through the VRS. This gives VRS callers single key access to extensions, the company operator, Department Calling Groups and Voice Mail.
Page 306 Outside caller may not be able to dial individual extensions or lines if the same first digit is defined here. Feature Cross Reference Direct Inward System Access (DISA) Voice Response System (VRS) Electra Elite IPK II Programming Manual 2 - 271...
Page 307: System Timers For Vrs/Disa
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-07 : System Timers for VRS/DISA Level: Description Use Program 25-07 : System Timers for VRS/DISA to set the value for the system timers which affect DID and DISA. Refer to the following chart for a description of each option, its range and default setting.
Page 308 Assign the delay time from switching from a normal incoming status to DID mode. If this time is set to “0”, the call will switch to DID mode immediately. Conditions None Feature Cross Reference Direct Inward System Access (DISA) Electra Elite IPK II Programming Manual 2 - 273...
Page 309: Disa User Id Setup
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-08 : DISA User ID Setup Level: Description Use Program 25-08 : DISA User ID Setup to set the 6-digit DISA password for each user. There are 15 users each with one 6-digit password.
Page 310: Class Of Service For Disa Users
Class 1~15 Conditions DISA Class of Service cannot be 0. Program 20-06 cannot be used to assign Class of Service to DISA trunks. Feature Cross Reference Direct Inward System Access (DISA) Electra Elite IPK II Programming Manual 2 - 275...
Page 311: Trunk Group Routing For Disa
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-10 : Trunk Group Routing for DISA Level: Description Use Program 25-10 : Trunk Group Routing for DISA to assign the Trunk Group route chosen when a user places a DISA call into the system and dials 9. Set Trunk Group Routing in Program 14-06.
Page 312: Disa Toll Restriction Class
Item Day/Night Toll Restriction Default Mode Class 1~15 Conditions Program 21-05 cannot be used to assign Toll Restriction to DISA trunks. Feature Cross Reference Direct Inward System Access (DISA) Toll Restriction Electra Elite IPK II Programming Manual 2 - 277...
Page 313: Alternate Trunk Group Routing For Disa
Document Revision 1 Electra Elite IPK II Program 25 : DID/DISA Setup 25-12 : Alternate Trunk Group Routing for DISA Level: Description Use Program 25-12 : Alternate Trunk Group Routing for DISA to define the trunk route selected when a DISA caller dials the Alternate Trunk Access Code. The route selected is based on the DISA caller’s Class of Service, which is in turn determined...
Page 314: System Option For Disa
VRS messages. --- Not Used --- --- Not Used --- Conditions None Feature Cross Reference Direct Inward System Access (DISA) Voice Response System (VRS) Electra Elite IPK II Programming Manual 2 - 279...
Page 315 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 280 Program 25 : DID/DISA Setup...
Page 316: Program 26 : Ars Service
--- Not Used --- --- Not Used --- Class of Service Match Access 0 = Disable (Off) 26-02 1 = Enable (On) F-Route Access COS Reference 0 = F-Route 26-02 1 = ARS 44-05 Electra Elite IPK II Programming Manual 2 - 281...
Page 317 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Automatic Route Selection 2 - 282 Program 26 : ARS Service...
Page 318: Dial Analysis Table For Ars/Lcr
F-Route Time Schedule Used = 0~500 (F-Route Selection Number). Refer to Program 44-04 : ARS/F-Route Selection for Time Schedule on page 2-398). ARS Class of Service 0~16 Dial Treatment for ARS 0~15 Electra Elite IPK II Programming Manual 2 - 283...
Page 319 Document Revision 1 Electra Elite IPK II Item Related Item Input Data Default Programming LCR Carrier Table 0~25 Select the Carrier Table to be used for dial edit. Table 1 is a special table - this table will be automatically used for all numbers that begin with “0”...
Page 320: Ars Dial Treatments
X - When ARS is enabled, X must be entered in the Dial Treatment in order for the system to output the extension number of the call’s originator to the black box for the E911 feature. Electra Elite IPK II Programming Manual 2 - 285...
Page 321 Document Revision 1 Electra Elite IPK II Input Data Dial Treatment Table Number 1~15 Item Item Input Data Default Treatment Code 24 characters maximum No Setting Conditions None Feature Cross Reference Automatic Route Selection 2 - 286 Program 26 : ARS Service...
Page 322: Ars Class Of Service
Automatic Route Selection uses ARS Class of Service when determining how to route extension calls. Input Data Extension Number Up to 8 digits Item Day/Night Class Default Mode 0~16 Conditions None Feature Cross Reference Automatic Route Selection Electra Elite IPK II Programming Manual 2 - 287...
Page 323: Lcr Carrier Table
Document Revision 1 Electra Elite IPK II Program 26 : ARS Service 26-05 : LCR Carrier Table Level: Description Use Program 26-05 : LCR Carrier Table to set the Carrier Table for LCR. Input Data LCR Carrier Table 1~25 Item...
Page 324: Lcr Authorization Table
Use Program 26-06 : LCR Authorization Table to set the Authorization Code Table for LCR. Input Data LCR Authorization Table 1~10 Item Item Input Data Default Authorization Code 10 digits maximum No Setting Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 289...
Page 325: Lcr Cost Center Code Table
Document Revision 1 Electra Elite IPK II Program 26 : ARS Service 26-07 : LCR Cost Center Code Table Level: Description Use Program 26-07 : LCR Cost Center Code Table to set the Cost Center Code for LCR. Input Data...
Page 326: Lcr Manual Override Access Code Table
LCR Manual Override Access Code Table 1~10 Item Item Input Data Default Manual Override Access Code (Dial) 4 digits maximum No Setting Carrier Table 0~25 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 291...
Page 327: Lcr Manual Override Exemption Table
Document Revision 1 Electra Elite IPK II Program 26 : ARS Service 26-09 : LCR Manual Override Exemption Table Level: Description Use Program 26-09 : LCR Manual Override Exemption Table to set Manual Override Exemption for LCR. Input Data LCR Carrier Table...
Page 328 Default No Setting No Setting No Setting No Setting No Setting No Setting No Setting No Setting No Setting No Setting No Setting No Setting Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 293...
Page 329: Transit Network Id Table
Document Revision 1 Electra Elite IPK II Program 26 : ARS Service 26-11 : Transit Network ID Table Level: Description Use Program 26-11 : Transit Network ID Table to define Transit Network ID for Alternate carrier access, which is referred from PRG26-03.
Page 330: Program 30 : Dss/Dls Console Setup
DSS Console Number 01~32 Item DSS Operation Mode Default = Business Mode = Hotel Mode = A CD Monitor Mode = BS/ACD Conditions None Feature Cross Reference Direct Station Selection (DSS) Console Hotel/Motel Electra Elite IPK II Programming Manual 2 - 295...
Page 331: Dss Console Extension Assignment
Document Revision 1 Electra Elite IPK II Program 30 : DSS/DLS Console Setup 30-02 : DSS Console Extension Assignment Level: Description Use Program 30-02 : DSS Console Extension Assignment to identify which extensions have DSS Consoles connected. Up to 32 different extensions with DSS Consoles can be set up. A single extension can have up to four 60-button DSS Consoles (32 is the maximum allowed per system).
Page 332: Dss Console Key Assignment
DSS Console Number 01~32 Index 2 Item Key Number Function Number Additional Data 01~60 0~99 (General Functional Level) Refer to Function Number List on the following pages. 00 ~ 99 (Appearance Functional Level) Electra Elite IPK II Programming Manual 2 - 297...
Page 333 Document Revision 1 Electra Elite IPK II Function Number List [1] General functional level (00~99) Function Function Additional Data LED Indication Number --- Not Used --- Red On: DSS / One-Touch Extension Number or any Extension Busy Numbers (up to 24 digits)
Page 334 Memo Dial None Meet – Me Conference None Override (Off-Hook None Signaling) Barge-In None Camp On Red On: Under Camp-On or Reservation Step Call None DND/FWD Override Call None Message Waiting None Electra Elite IPK II Programming Manual 2 - 299...
Page 335 Document Revision 1 Electra Elite IPK II Function Number List (Continued) [1] General functional level (00~99) Function Function Additional Data LED Indication Number Rapid Blink (Red): Under Monitored Room Monitoring Slow Blink (Red): Under Monitoring With Room Monitor there are two parties in the monitor, one being monitored and one who is monitoring.
Page 336 Automated Attendant for Extension Number or None Extension Department Group Number Message Change for Voice Extension Number or None Attendant Department Group Number Keypad Facility Key Keypad Hold Key Keypad Retrieve Key Electra Elite IPK II Programming Manual 2 - 301...
Page 337 Document Revision 1 Electra Elite IPK II Function Number List (Continued) [1] General functional level (00~99) Function Function Additional Data LED Indication Number Keypad Conference Key Toll Restriction in Credit Red On: Voice Mail (In-Skin) Extension Number or Pilot Access to Voice Mail...
Page 338 Slow Blink (Red): Disable ACD Queue Status Display Default The DSS keys 01~60 of all DSS consoles = DSS/One-Touch key 101~160. Conditions None Feature Cross Reference Direct Station Selection (DSS) Console Electra Elite IPK II Programming Manual 2 - 303...
Page 339: Dss Console Lamp Table
Document Revision 1 Electra Elite IPK II Program 30 : DSS/DLS Console Setup 30-05 : DSS Console Lamp Table Level: Description Use Program 32-05 : DSS Console Lamp Table to define the LED patterns for functions on the DSS consoles.
Page 340: Table 2-7 Led Patterns For Dss Console
Electra Elite IPK II Document Revision 1 Input Data Lamp Item Item Pattern Default Data VM Message Indication 3 (RW) Table 2-7 LED Patterns for DSS Console Electra Elite IPK II Programming Manual 2 - 305...
Page 341 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Direct Station Selection (DSS) Console 2 - 306 Program 30 : DSS/DLS Console Setup...
Page 342: Program 31 : Paging Setup
Enter characters T-V, t-v, 8. Enter characters W-Z, w-z, 9. Enter characters: α ε θ “ & ’ ) ô Õ ú ä ö ü Enter characters: σ ∞ < > ¢ £ Electra Elite IPK II Programming Manual 2 - 307...
Page 343 Document Revision 1 Electra Elite IPK II Key for Entering Names (Continued) When entering names in the procedures below, refer to this chart. Names can be up to 12 digits long. Use this keypad When you want to. . .
Page 344: Internal Paging Group Assignment
(not receive) All Call Internal Paging announcements. If combined, Paging zones should be restricted as well, change the internal page zone group in Program 31-07-01 to “0”. Conditions None Feature Cross Reference Paging, Internal Electra Elite IPK II Programming Manual 2 - 309...
Page 345: Internal Paging Group Settings
Document Revision 1 Electra Elite IPK II Program 31 : Paging Setup 31-03 : Internal Paging Group Settings Level: Description Use Program 31-03 : Internal Paging Group Settings to assign names to Internal Paging Groups (i.e., Page Zones) and to define the splash tone for Internal Paging.
Page 346 Paging announcement. 1 = Mute 2 = No Tone (None) Default Item 01 : Internal Paging Group Name Extension Name Paging Group Group 1 Group 2 Group 64 Electra Elite IPK II Programming Manual 2 - 311...
Page 347 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Paging, Internal 2 - 312 Program 31 : Paging Setup...
Page 348: External Paging Zone Group
External Paging group. Users call the External Paging group when broadcasting announcements to the external zone. When programming, the zones on the PGD(2)-U10 adapter are numbers 1~8. On the Electra Elite IPK II system, the CPUII’s zone is number 9.
Page 349: Universal Night Answer/Ring Over Page
Document Revision 1 Electra Elite IPK II Program 31 : Paging Setup 31-05 : Universal Night Answer/Ring Over Page Level: Description Use Program 31-05 : Universal Night Answer to assign Universal Night Answer ringing to each External Paging zone. For each trunk port, make a separate entry for each External Paging zone.
Page 350: External Speaker Control
CPUII external page zone, speaker 9 should be left at “1”. CODEC Transmit Gain Setup 1~63 (-15.5 ~ +15.5dB) 1~63 (-15.5 ~ +15.5dB) CODEC Receive Gain Setup Electra Elite IPK II Programming Manual 2 - 315...
Page 351 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Paging, External 2 - 316 Program 31 : Paging Setup...
Page 352: Combined Paging Assignments
External Paging Group Number 0~8 (0 = All External Paging) Item Internal Paging Default Group Number 0~64 (0 = All internal paging) Conditions None Feature Cross Reference Paging, External Paging, Internal Electra Elite IPK II Programming Manual 2 - 317...
Page 353: Bgm On External Paging
Document Revision 1 Electra Elite IPK II Program 31 : Paging Setup 31-08 : BGM on External Paging Level: Description Use Program 31-08 : BGM on External Paging to set the Background Music option for each External Paging zone. If enabled, the system will play Background Music over the zone when it is idle.
Page 354: Program 32 : Door Box And Sensor Setup
Forward by Door Box call. When this timer expires, the caller will hear busy tone for 3 seconds (fixed timer) and the call will then be disconnected. Conditions None Feature Cross Reference Door Box Electra Elite IPK II Programming Manual 2 - 319...
Page 355: Door Box Ring Assignment
Document Revision 1 Electra Elite IPK II Program 32 : Door Box and Sensor Setup 32-02 : Door Box Ring Assignment Level: Description Use Program 32-02 : Door Box Ring Assignments to assign the extension which will ring when a caller presses the associated Door Box call button.
Page 356: Door Box Basic Setup
CODEC Transmit Gain Setup 1~63 (-15.5 ~ +15.5dB) (PGD to Door Box) CODEC Receive Gain Setup 1~63 (-15.5 ~ +15.5dB) (Door Box to PGD) Conditions None Feature Cross Reference Door Box Electra Elite IPK II Programming Manual 2 - 321...
Page 357 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 322 Program 32 : Door Box and Sensor Setup...
Page 358: Program 33 : Cta And Aci Setup
P r o g r a m Input Data ACI Port Number 01~96 Item ACI Type Default = None = MOH/BGM (Input) = External Audio Port (Input/ Output) Conditions None Feature Cross Reference Analog Communications Interface (ACI) Electra Elite IPK II Programming Manual 2 - 323...
Page 359: Aci Department Calling Group
Document Revision 1 Electra Elite IPK II Program 33 : CTA and ACI Setup 33-02 : ACI Department Calling Group Level: Description Use Program 33-02 : ACI Department Calling Group to assign ACI ports to Department Groups. An ACI port can only be in one group.
Page 360: Program 34 : Tie Line Setup
Enter 0 if the Tie Line should not send dial tone. System Toll = No Determine if an incoming Tie Restriction = Yes Line call should be subject to Toll Restriction. Electra Elite IPK II Programming Manual 2 - 325...
Page 361 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Tie Lines 2 - 326 Program 34 : Tie Line Setup...
Page 362: E&M Tie Line Class Of Service
Trunk Port Number 1~200 Item Day/Night Related Class Default Mode Program 1~15 20-14 Conditions Program 20-06 cannot be used to assign Class of Service to Tie lines. Feature Cross Reference Tie Lines Electra Elite IPK II Programming Manual 2 - 327...
Page 363: Trunk Group Routing For E&M Tie Lines
Document Revision 1 Electra Elite IPK II Program 34 : Tie Line Setup 34-03 : Trunk Group Routing for E&M Tie Lines Level: Description Use Program 34-03 : Trunk Group Routing for E&M Tie Lines to assign the trunk group route 1~8 or 1~100) chosen when a user seizes a Tie Line and dials 9. (Set Trunk Group Routing in Program 14-07.) If the system has Automatic Route...
Page 364: E&M Tie Line Toll Restriction Class
001~200 Item Day/Night Toll Restriction Related Default Mode Class Program 1~15 21-05 14-01-08 Conditions Program 20-06 cannot be used to assign Toll Restriction to Tie Lines. Feature Cross Reference Tie Lines Electra Elite IPK II Programming Manual 2 - 329...
Page 365: Tie Line Outgoing Call Restriction
Document Revision 1 Electra Elite IPK II Program 34 : Tie Line Setup 34-05 : Tie Line Outgoing Call Restriction Level: Description Use Program 34-05 : Tie Line Outgoing Call Restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.g., dialed from a Tie Line).
Page 366: Add / Delete Digit For E&M Tie Line
Incoming Trunk Group Number 001~100 Item Item Input Data Default Delete Digit 0~255 (255 = delete all digits) Additional Dial Digits Up to 4 digits No Setting Conditions None Feature Cross Reference Tie Lines Electra Elite IPK II Programming Manual 2 - 331...
Page 367: E&M Tie Line Timer
Document Revision 1 Electra Elite IPK II Program 34 : Tie Line Setup 34-07 : E&M Tie Line Timer Level: Description Use Program 34-07 : E&M Tie Line Timer to define the system service tone timers. Input Data Item Item...
Page 368: Toll Restriction Data For E&M Tie Lines
Restriction is enabled in Program 21-05-13. Input Data Class of Service 01~15 Item Table Related Dial Data Default Program 01~20 Up to 10 Digits No Setting 21-05-13 Conditions None Feature Cross Reference Tie Lines Electra Elite IPK II Programming Manual 2 - 333...
Page 369: Ani/Dnis Service Options
Document Revision 1 Electra Elite IPK II Program 34 : Tie Line Setup 34-09 : ANI/DNIS Service Options Level: Description Use Program 34-09 : ANI/DNIS Service Options to define the ANI//DNIS service option setup for E&M Class of Service. Input Data...
Page 370 This option lets you determine how the system = Route Caller to will handle an ANI/DNIS call if a data error is Ring Group detected in the incoming data string. Specified in Program 25-03 (Transfer) Electra Elite IPK II Programming Manual 2 - 335...
Page 371 Document Revision 1 Electra Elite IPK II Default Item Related Name Input Data Program COS 01~14 COS 15 = Play Busy or 25-04 Routing When Destination Busy or No Answer Ringback Tone to Caller (Busy/ This option lets you determine how the system...
Page 372: Program 35 : Smdr Account Code Setup
SMDR report. Minimum Call Duration 0~65535 (sec) (0 = All) The duration of the call must be at least this interval to be included on the SMDR report. Electra Elite IPK II Programming Manual 3 - 337...
Page 373 Document Revision 1 Electra Elite IPK II Item Item Input Data Default Minimum Ring Time 0~65535 (sec) (0 = All) A call must ring for at least this interval to be included on the SMDR report. Format Selection 0 = NA Type...
Page 374: Smdr Output Options
Summary (Monthly) = Not Displayed = Displayed Set this option to (1) to have the SMDR report provide a monthly summary (at midnight on the last day of the month). Electra Elite IPK II Programming Manual 3 - 339...
Page 375 Document Revision 1 Electra Elite IPK II Item Item Input Data Default Toll Charge Cost = Not Displayed = Displayed Set this option to (1) have the SMDR report include toll charges. Incoming Call = Not Displayed = Displayed Enable this option (1) to have the SMDR report include incoming calls.
Page 376 Print Mode for Caller Name of Incoming Call = Normal = Line Feed Determine how SMDR should print Caller Name of Incoming Call. Conditions None Feature Cross Reference Station Message Detail Recording Electra Elite IPK II Programming Manual 3 - 341...
Page 377: Smdr Port Assignment For Trunk Group
Document Revision 1 Electra Elite IPK II Program 35 : SMDR Account Code Setup 35-03 : SMDR Port Assignment for Trunk Group Level: Description Use Program 35-03 : SMDR Port Assignment for Trunk Group to assign the SMDR port for each trunk group. For each Trunk Group, select the SMDR port to which the incoming SMDR information should be sent.
Page 378: Smdr Port Assignment For Department Groups
SMDR port to which the outgoing SMDR information should be sent. There are 64 available Department Groups. Input Data Department Group Number 01~64 Item SMDR Port No. Default Conditions None Feature Cross Reference Station Message Detail Recording Electra Elite IPK II Programming Manual 3 - 343...
Page 379: Account Code Setup
Document Revision 1 Electra Elite IPK II Program 35 : SMDR Account Code Setup 35-05 : Account Code Setup Level: Description to set various Account Code options for an Program 35-01 : Account Code Setup extension’s Class of Service. Assign a Class of Service to extensions in Program 20-06.
Page 380 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Account Codes Electra Elite IPK II Programming Manual 3 - 345...
Page 381: Verified Account Code Table
Document Revision 1 Electra Elite IPK II Program 35 : SMDR Account Code Setup 35-06 : Verified Account Code Table Level: Description to enter Account Codes into the Program 35-06 : Verified Account Code Table Verified Account Code list. You can enter up to 2000 codes from 3~6 digits long, using the characters 0~9 or #.
Page 382: Program 40 : Voice Recording System
0000 Maintenance Time Specify time to maintain (0000 = No Setting) for DSPII-U10 Unit record media. Automatically Erase 0~180 Message Escape Service = Disable (Off) during Automated = Enable (On) Attendant Electra Elite IPK II Programming Manual 2 - 347...
Page 383 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Mail Integration (Analog) 2 - 348 Program 40 : Voice Recording System...
Page 384: Mailbox Setup
A mailbox number should use the same number of an extension. Mailbox Password Dial (4 digits) No Setting If not required, leave this option empty. Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 349...
Page 385: Message Recording Setup
Document Revision 1 Electra Elite IPK II Program 40 : Voice Recording System 40-03 : Message Recording Setup Level: Description to define the auto-answering operation Program 40-03 : Message Recording Setup of the Voice Mail (DSPII-U10 Unit). Input Data Item...
Page 386: Live Recording Setup
= Starting Extension Callback Specify the recall destination when a of Conversation transfer destination is not Recording (Start) found. = Last Extension of Conversation Recording (Last) Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 351...
Page 387: Call Information Setup
Document Revision 1 Electra Elite IPK II Program 40 : Voice Recording System 40-05 : Call Information Setup Level: Description to define the incoming notice of the Voice Program 40-05 : Call Information Setup Mail (DSPII-U10 Unit). Input Data Item...
Page 388: Voice Mail Automated Attendant Data Setup
Item Input Data Default Operation Mode = Automated Attendant = Not Used Guidance Message Number 0~48 Message Box Number for 0~300 Leaving a Message Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 353...
Page 389: Voice Prompt Language Assignment For Vrs
Document Revision 1 Electra Elite IPK II Program 40 : Voice Recording System 40-07 : Voice Prompt Language Assignment for VRS Level: Description to specify the Program 40-07 : Voice Prompt Language Assignment for VRS language to be used for the VRS prompts.
Page 390: Voice Prompt Language Assignment For Mailboxes
Input Data Item Item Input Data Default Voice Prompt Language Assignment for = Japanese Mailboxes = English = German = Norwegian Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 355...
Page 391: Voice Mail Multiple Address Group Setup
Document Revision 1 Electra Elite IPK II Program 40 : Voice Recording System 40-09 : Voice Mail Multiple Address Group Setup Level: Description to define the broadcast Program 40-09 : Voice Mail Multiple Address Group Setup group of a Voice Mail (DSPII-U10 Unit) mailbox.
Page 392: Voice Announcement Service Option
This item assigns the VRS Message number to be message ) used as Private Call Refuse. When Fixed message is set, VRS message guidance is: “Service finished. Disconnect the line, please”. Electra Elite IPK II Programming Manual 2 - 357...
Page 393 Document Revision 1 Electra Elite IPK II Input Data Set VRS Message for Caller ID Refuse 0~49 (0 = No message) (VRS Msg CID) (49 = Fixed message ) This item assigns the VRS Message number to be used as Caller ID Refuse.
Page 394: Pre-Amble Message Assignment
VAU message will be sent to the outside caller. Input Data Trunk Port Number 001~200 Item Day/Night VAU Message Default Mode Number 0~48 (0=No Service) Conditions None Feature Cross Reference Voice Response System (VRS) Electra Elite IPK II Programming Manual 2 - 359...
Page 395 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 360 Program 40 : Voice Recording System...
Page 396: Program 41 : Acd Setup
Login ID Code Digit 0~20 (0 = No Login ID) ACD MIS Connection = None Ports = LAN (CPUII) --- Not Used --- Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 361...
Page 397: Acd Group And Agent Assignments
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-02 : ACD Group and Agent Assignments Level: Description , for each ACD extension Program 41-02 : ACD Group and Agent Assignments number, assign an ACD Group (1~64). An ACD Group number is assigned to each Work Period number (1~8).
Page 398: Incoming Ring Group Assignment For Acd Group
Determine whether an incoming call to (7 = Highest Priority) a trunk ring group should follow a priority assignment. 0 = Normal 1~7: 1 = Lowest Priority 7 = Highest Priority Electra Elite IPK II Programming Manual 2 - 363...
Page 399 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Ring Groups 2 - 364 Program 41 : ACD Setup...
Page 400: Acd Group Supervisor
If you assign an extension as a ACD Group Supervisor in this program, you cannot program the same extension as a System Supervisor in Program 41-01-01. Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 365...
Page 401: Acd Agent Work Schedules
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-05 : ACD Agent Work Schedules Level: Description to set up the Work Schedules for Program 41-05 : ACD Agent Work Schedules ACD Agents and Groups. For each ACD Work Schedule (1~4), designate the start and stop times for each of the eight Work Periods.
Page 402: Trunk Work Schedules
ACD Work Schedule Time Pattern Number Item Work Period Start Time End Time Default Mode Number 0000~2359 0000~2359 (Start) 0000 (End) 0000 Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 367...
Page 403: Acd Weekly Schedule Setup
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-07 : ACD Weekly Schedule Setup Level: Description to assign the four Work Schedules Program 41-07 : ACD Weekly Schedule Setup (1~4) to days of the week. The assignments you make in this program apply to both the ACD Agent Work Schedules (Program 41-05) and the Trunk Work Schedules (Program 41-06).
Page 404: Acd Overflow Options
68 = Incoming Ring Group (Program 41-08-06) Delay = ACI Announcement = VRS Source Type ACD Overflow 0~64800 (sec) Transfer Time 0~1999 1999 System Speed Dial Bin (Used when 41-08-02 is set to Electra Elite IPK II Programming Manual 2 - 369...
Page 405 Document Revision 1 Electra Elite IPK II Incoming Ring 1~100 Group (Used when 41-08-02 is set to Conditions Delay announcement functions are not available for ACD pilot number call. Feature Cross Reference Automatic Call Distribution (ACD) 2 - 370 Program 41 : ACD Setup...
Page 406: Acd Overflow Table Setting
If, while the call is ringing, the extension to which the call was transferred becomes available, both the extension and the overflow ACD group will ring. Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 371...
Page 407: Aci Delay Announcement
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-10 : ACI Delay Announcement Level: Description to define the ACI port number to be Program 41-10 : ACI Delay Announcement used for the delay announcement. This program is activated when the delay announcement source and options are assigned as ACI in Program 41-08-03.
Page 408: Vrs Delay Announcement
After 2nd Delay Message Queue Depth Announcement 0 = Disable 1 = After 1st (1st) (Requires VRS) 2 = After 2nd (2nd) 3 = After 1st and 2nd (1st and 2nd) Electra Elite IPK II Programming Manual 2 - 373...
Page 409 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Automatic Call Distribution (ACD) 2 - 374 Program 41 : ACD Setup...
Page 410: Night Announcement Setup
0 = No Setting ACD Night Announce Sending Time 0~64800 (sec) Conditions The night announcement function is not available for ACD pilot number call. Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 375...
Page 411: Vrs Message Number For Night Announcement
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-13 : VRS Message Number for Night Announcement Level: Description to define the VRS message number to Program 41-13 : VRS Night Announcement be used as the night announcement. This program is activated when the night announcement source is assigned as VRS in Program 41-12.
Page 412: Acd Options
Program 41-03-03. Automatic Answer = Off = On Enable/disable Automatic Answer for agents using headsets. --- Not Used --- Electra Elite IPK II Programming Manual 2 - 377...
Page 413 Document Revision 1 Electra Elite IPK II Item Item Input Data Default = Enable (Yes) Call Queuing after 2nd Announcement = Disable (No) Use this option to determine whether an outside caller should hear a final announcement [ex: the company is...
Page 414: Acd Queue Alarm Information
ACD Group No. 01~64 Item Item Input Data Default Number of Calls in ACD Queue to Activate 0~200 Alarm Information 0 = No Alarm Interval time of Alarm Information 0~64800 (sec) Electra Elite IPK II Programming Manual 2 - 379...
Page 415 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Automatic Call Distribution (ACD) 2 - 380 Program 41 : ACD Setup...
Page 416: Acd Threshold Overflow
= The last waiting call is handle calls when the number of transferred calls in queue exceeds the threshold. = Send Busy Tone Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 381...
Page 417: Acd Login Mode Setup
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-17 : ACD Login Mode Setup Level: Description to define the ACD login mode for each Program 41-17 : ACD Login Mode Setup extension. If the AIC Login Mode is enabled, set the AIC Login and AIC Logout service codes for the AIC members in Program 11-13-08 and 11-13-09.
Page 418: Acd Agent Identity Code Setup
ACD Group Number in Mode 6 0~64 0 = No Setting 0~64 ACD Group Number in Mode 7 0 = No Setting 0~64 ACD Group Number in Mode 8 0 = No Setting Electra Elite IPK II Programming Manual 2 - 383...
Page 419: Acd Queue Display Settings
Document Revision 1 Electra Elite IPK II Program 41 : ACD Setup 41-20 : ACD Queue Display Settings Level: Description to assign the options for the ACD Program 41-20 : ACD Queue Display Settings Queue Status Display feature. This program allows the Queue Status Display, as well as an alarm to sound, when the parameters in this program are met.
Page 420 Enable or disable the queue alarm. ACD Call Waiting Alarm Hold Time 0~64800 (sec) Set how long the Call Waiting Alarm should sound. Conditions None Feature Cross Reference Automatic Call Distribution (ACD) Electra Elite IPK II Programming Manual 2 - 385...
Page 421 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 386 Program 41 : ACD Setup...
Page 422: Program 42 : Hotel Setup
0 = Only Confirmation Tone Call (Hotel Mode) = VRS Message = Time Information and VRS Wake Up Call Message Assignment 0~48 = VRS Message Number Conditions None Feature Cross Reference Hotel/Motel Electra Elite IPK II Programming Manual 2 - 387...
Page 423: Hotel/Motel Telephone Setup
Document Revision 1 Electra Elite IPK II Program 42 : Hotel Setup 42-02 : Hotel/Motel Telephone Setup Level: Description to define the basic operation of the Program 42-02 : Hotel/Motel Telephone Setup Hotel/Motel extensions. Input Data Extension Number Up to 8 digits Item No.
Page 424: Class Of Service Options (Hotel/Motel)
Room to Room Call Restriction 0 = Off 1 = On DND Setting for Own Extension 0 = Off 1 = On 0 = Off Wake Up Call Setting for Own Extension 1 = On Electra Elite IPK II Programming Manual 2 - 389...
Page 425 Document Revision 1 Electra Elite IPK II Default Item Input Item Data Class Class 02~15 --- Not Used --- 0 = Off SLT Room Monitor 1 = On Enable (1) or disable (0) a single line telephone’s ability to use Room Monitor.
Page 426: Hotel Mode One-Digit Service Codes
Default Dial Number 1~9,0, Up to 8 digits No Setting Conditions The 1-digit codes you assign in this program wait until the interdigit timer expires before executing. Feature Cross Reference Hotel/Motel Electra Elite IPK II Programming Manual 2 - 391...
Page 427: Hotel Room Status Printer
Document Revision 1 Electra Elite IPK II Program 42 : Hotel Setup 42-05 : Hotel Room Status Printer Level: Description to set the CTA port to output the Hotel Program 42-05 : Hotel Room Status Printer Data (Check-Out sheet, Room Status, etc.) and the output options for the Hotel/Motel feature.
Page 428: Program 44 : Ars/F-Route Setup
44-10. If there is a match, the pattern defined in that program is used. If not, the F-Route pattern in Program 44-09 and time setting in 44-08 are used. Conditions None Feature Cross Reference Automatic Route Selection (ARS) Uniform Numbering Network Electra Elite IPK II Programming Manual 2 - 393...
Page 429: Dial Analysis Table For Ars/F-Route Access
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-02 : Dial Analysis Table for ARS/F-Route Access Level: Description to set the Program 44-02 : Dial Analysis Table for ARS/F-Route Access Pre-Transaction Table for selecting ARS/F-Route. Input Data...
Page 430 This may be required if the central office at the destination does not send dial tone. Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 395...
Page 431: Dial Analysis Extension Table
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-03 : Dial Analysis Extension Table Level: Description When Program 44-02-02 is set to type “3”, use Program 44-03 : Dial Analysis to set the dial extension analysis table. These tables are used when Extension Table the analyzed digits must be more than 8 digits.
Page 432 With Program 44-01 set to 1, Program 44-04 is then checked. Dial Analysis Table Number : 252 Item Item Input Data Default Next Table Area Number Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 397...
Page 433: Ars/F-Route Selection For Time Schedule
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-04 : ARS/F-Route Selection for Time Schedule Level: Description to assign each ARS/ Program 44-04 : ARS/F-Route Selection for Time Schedule F-Route Selection number to an ARS/F-Route table number for each ARS/F-Route time mode.
Page 434: Ars/F-Route Table
(defined in Program 44-07). Gain Table Number for Tandem Connections 0~500 0 = No Setting Select the gain table number to be used for the tandem call (defined in Program 44-07). Electra Elite IPK II Programming Manual 2 - 399...
Page 435 Document Revision 1 Electra Elite IPK II Item Item Input Data Default ARS Class of Service 0~16 Select the ARS Class of Service to be used for the table. An extension’s ARS COS is determined in Program 26-04-01. Dial Treatment 0~15 Select the Dial Treatment to be used for the table.
Page 436: Additional Dial Table
Additional Dial Default Up to 24 digits No Setting Enter: 1-9, 0, , #, Pause (press line key 1 to enter a pause) Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 401...
Page 437: Gain Table For Ars/F-Route Access
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-07 : Gain Table for ARS/F-Route Access Level: Description to set the gain/PAD table. If Program 44-07 : Gain Table for ARS/F-Route Access an extension dials ARS/F-Route number: The Extension Dial Gain Table is activated, which is assigned in Program 44-05.
Page 438 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 403...
Page 439: Time Schedule For Ars/F-Route
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-08 : Time Schedule for ARS/F-Route Level: Description to define the daily pattern of the Program 44-08 : Time Schedule for ARS/F-Route ARS/F-Route feature. ARS/F-Route has 10 time patterns. These patterns are used in Program 44-09 and 44-10.
Page 440 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 405...
Page 441: Weekly Schedule For Ars/F-Route
Document Revision 1 Electra Elite IPK II Program 44 : ARS/F-Route Setup 44-09 : Weekly Schedule for ARS/F-Route Level: Description to define a weekly schedule for Program 44-09 : Weekly Schedule for ARS/F-Route using ARS/F-Route. The pattern number is defined in Program 44-08-01.
Page 442: Holiday Schedule For Ars/F-Route
The pattern number is defined in Program 44-08-01. Input Data Item Schedule Pattern Date Default Number 0101~1231 0~10 0 = No Setting Conditions None Feature Cross Reference Automatic Route Selection (ARS) Electra Elite IPK II Programming Manual 2 - 407...
Page 443 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 408 Program 44 : ARS/F-Route Setup...
Page 444: Program 45 : Voice Mail Integration
CCIS Centralized Voice Mail Number Dial (up to 8 digits) No Setting Assign the pilot number to Centralized Voice Mail over CCIS Link. This is only assigned in the remote switches. Electra Elite IPK II Programming Manual 2 - 409...
Page 445 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Mail Integration (Analog) 2 - 410 Program 45 : Voice Mail Integration...
Page 446: Program 47 : In-Mail
## characters. The system substitutes the port number for the last #. In-Mail Using the default name ## for example, the keyset display shows IPK II In-Mail #1 when calling port 1. Electra Elite IPK II Programming Manual 2 - 411...
Page 447 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Subscriber Message Length 1~4095 (sec) 120 (sec) (Subs Msg Length) Use this option to set the maximum length of recorded messages for: Subscriber Mailbox users dialing RS to record and send a message.
Page 448 M is the number of new messages in received the the extension’s mailbox. message. # is the digit normally used by the pager service for positive disconnect. Electra Elite IPK II Programming Manual 2 - 413...
Page 449 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Delay in Dialing Digital Pager Callback 0~99 (sec) 9 (sec) Number (Pager Dial Delay) Use this option to set the delay (0~99 seconds) that occurs just before IPK II...
Page 450 (like the above example), or if the call is picked up by an answering machine with insufficient outgoing message volume. Electra Elite IPK II Programming Manual 2 - 415...
Page 451 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Wait for Answer Non-Pager Callout 1~99 (rings) 5 (rings) Attempts (Notify RNA Rings) If a non-pager callout rings the destination longer than this interval (1-99 rings), IPK II In-Mail marks the call as unanswered (Ring No Answer) and hangs up.
Page 452 Electra Elite IPK II Document Revision 1 Conditions When changing 47-01-01, a system reset is required for the new setting to take effect. Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 417...
Page 453: Ipk Ii In-Mail Station Mailbox Options
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-02 : IPK II In-Mail Station Mailbox Options Level: Description IPK II In-Mail to set up a station’s (extension’s) 47-02: Station Mailbox Options mailbox. Station mailboxes are automatically assigned as Subscriber Mailboxes.
Page 454 Use this option to determine how long a Subscriber Mailbox will retain held and saved messages. If a message is left in a Subscriber Mailbox longer than this interval, IPK II In-Mail deletes it. Electra Elite IPK II Programming Manual 2 - 419...
Page 455 (if the mailbox message storage capacity is reached) “You have reached the recording limit” (if the recorded message is too long) The Electra Elite IPK II telephone system software provides an additional Conversation Record beep. This beep repeats according to the setting of...
Page 456 The digits the caller can dial depends on the setting of the Next Call Routing Mailbox and Alternate Next Call Routing Mailbox options. Directory List 0 = None 0 (None) 1~8 = List Number = All Electra Elite IPK II Programming Manual 2 - 421...
Page 457 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Mail 2 - 422 Program 47 : In-Mail...
Page 458: Ipk Ii In-Mail Master Mailbox Options
47-06 : Master Subscriber Mailbox Options to set up the Master Mailbox options. If the Master Mailbox is a Directory Mailbox (4), go 47-14 : Master Directory Mailbox Options to set up the Master Mailbox options. Electra Elite IPK II Programming Manual 2 - 423...
Page 459 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Mail 2 - 424 Program 47 : In-Mail...
Page 460: Master Call Routing Mailbox Options
Timeout action programmed, the caller routes to that destination. When the associated Dial Action Table does not have a Timeout action programmed, the Instruction Menu repeats 3 times and then IPK II In-Mail hangs up. Electra Elite IPK II Programming Manual 2 - 425...
Page 461 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Fax Detection 0 = No (Disabled) 0 (No - Disabled) 1 = Yes (Enabled) (Fax Detection) Use this option to enable or disable Fax Detection for the Call Routing Mailbox. In...
Page 462: Master Announcement Mailbox Options
For more detail on this interaction, refer to Direct Announcement Mailbox Routing in the IPK II In-Mail System Guide and Routed Announcement Mailbox Routing in the IPK II In-Mail System Guide. Electra Elite IPK II Programming Manual 2 - 427...
Page 463 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Hang Up After 0 = No (Disabled) 0 (No - Disabled) 1 - Yes (Enabled) (HangUp) Use this option along with Next Call Routing Mailbox and Repeat Count above to provide additional routing options to Automated Attendant callers.
Page 464: Master Subscriber Mailbox Options
IPK II In-Mail listens to the entire retains the message as a new message. new message and hangs up, IPK II In-Mail saves the message. Electra Elite IPK II Programming Manual 2 - 429...
Page 465 “You have reached the recording limit” (if the recorded message is too long) The Electra Elite IPK II telephone system software provides an additional Conversation Record beep. This beep repeats according to the setting of Program 45-01-06: Voice Mail Integration Options: Record Alert Tone Interval Time (0~64800 seconds).
Page 466 Subscriber Mailbox recorded or default 01=16. greeting. The digits the caller can dial depends on the setting of the Next Call Routing Mailbox and Alternate Next Call Routing Mailbox options. Electra Elite IPK II Programming Manual 2 - 431...
Page 467 Document Revision 1 Electra Elite IPK II Input Data Item Item Input Data Default Directory List 0 = None 1~8 = List Number = All Conditions None Feature Cross Reference Voice Mail 2 - 432 Program 47 : In-Mail...
Page 468: Ipk Ii In-Mail Routing Mailbox Options
Mailboxes 01~08 = 1 (Call Routing) 2 (Announcement) (Mailbox Type) Mailboxes 09~16 = 2 4 (Directory) Use this option to set the Routing Mailbox type. (Announcement) Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 433...
Page 469: Call Routing Mailbox Options
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-08 : Call Routing Mailbox Options Level: Description to set the options for mailboxes assigned as 47-08: Call Routing Mailbox Options Call Routing Mailboxes in 47-07-02: Routing Mailbox Type...
Page 470 47-01-06 : Fax Extension. If disabled, the Automated Attendant will not detect incoming fax calls. Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 435...
Page 471: Announcement Mailbox Options
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-09 : Announcement Mailbox Options Level: Description to set the options for mailboxes assigned 47-09: Announcement Mailbox Options as Announcement Mailboxes in 47-07-02: Routing Mailbox Type Input Data Item...
Page 472 Direct Announcement Mailbox Routing in the IPK II In-Mail System Guide and Routed Announcement Mailbox Routing in the IPK II In-Mail System Guide. Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 437...
Page 473: Ipk Ii In-Mail Trunk Options
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-10 : IPK II In-Mail Trunk Options Level: Description IPK II In-Mail to assign IPK II In-Mail options for each trunk. 47-10: Trunk Options Currently, only is available. 47-10-01: Answer Table Assignment...
Page 474: Ipk Ii In-Mail Answer Table Options
Use this option to enable or disable Answer Schedule Override for the selected Answer Table. If enabled (and you make an entry for Override Mailbox below), the active Answer Table will route calls to the Override Mailbox. Electra Elite IPK II Programming Manual 2 - 439...
Page 475 Document Revision 1 Electra Elite IPK II Input Data (Continued) Item Item Input Data Default Override Mailbox Category 0 (Undefined) (Undefined) 1 (Subscriber (Override MB Ctg) Mailbox - STA) Use this option to specify the category of the 2 (Master Mailbox) mailbox to which Automated Attendant calls should route when you enable Answer Schedule Override.
Page 476 When 10 Answer Schedules within an Answer Table are not sufficient, use this option to link two Answer Tables together. IPK II In-Mail treats the two linked tables as a single 20 entry Answer Table. Electra Elite IPK II Programming Manual 2 - 441...
Page 477 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Mail 2 - 442 Program 47 : In-Mail...
Page 478: Ipk Ii In-Mail Answer Schedules
The time on the start day the schedule should start. The time on the stop day the schedule should stop. The Call Routing or Announcement Mailbox used to answer the calls. (continued on next page) Electra Elite IPK II Programming Manual 2 - 443...
Page 479 Document Revision 1 Electra Elite IPK II Input Data (Continued) Item Item Input Data Default (continued from previous page) 0 (Undefined) Answer Table 1/ Schedule 1 = 2 1 (Day of the Week) 3. Date (Range of Days) A type 3 Answer Schedule runs only on a 2 (Range of Days) specific day of the year.
Page 480 Week (Type 1), Range of Days (Type 2), and 0000 Date (Type 3) schedules. (To make a schedule (Undefined). run continuously, make the same entry for 47-12-07: Schedule Start Time and 47-12-08: Schedule End Time.) Electra Elite IPK II Programming Manual 2 - 445...
Page 481 Document Revision 1 Electra Elite IPK II Example Type 1 (Day of the Week) Answer Schedule Options Type 1 (Day of Week) Example In this example, Answer Table 1 routes calls as follows: Schedule 1 uses Routing Mailbox 2 and runs Sunday from 8:30AM to 5:00PM.
Page 482 47-12-05: Entry01 End Day = 1 (Entry does not matter) 47-12-06: Entry01 Date (MMDD) = 0000 (Entry does not matter) 47-12-07: Entry01 Start Time = 0900 (9:00AM) 47-12-08: Entry01 End Time = 1000 (10:00PM) Electra Elite IPK II Programming Manual 2 - 447...
Page 483 Document Revision 1 Electra Elite IPK II Type 2 (Range of Days) Answer Schedule Options Type 2 (Range of Days) Example In this example, Answer Table 1 routes calls as follows: Schedule 1 uses Routing Mailbox 1 and runs Sunday through Wednesday from 8:30AM to 5:00PM.
Page 484 47-12-05: Entry01 End Day = 5 (Thursday) 47-12-06: Entry01 Date (MMDD) = 0000 (Entry does not matter) 47-12-07: Entry01 Start Time = 1100 (11:00AM) 47-12-08: Entry01 End Time = 1300 (1:00PM) Electra Elite IPK II Programming Manual 2 - 449...
Page 485 Document Revision 1 Electra Elite IPK II Type 3 (Date) Answer Schedule Options Type 3 (Date) Example In this example, Answer Table 1 routes calls as follows: Schedule 1 uses Routing Mailbox 1 and runs every day from 8:30AM to 5:00PM.
Page 486 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 451...
Page 487: Ipk Ii In-Mail Dial Action Tables
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-13 : IPK II In-Mail Dial Action Tables Level: Description IPK II In-Mail to set up the IPK II In-Mail Dial Action 47-13: Dial Action Tables Tables. The Dial Action Table defines the options than an Automated Attendant caller can dial.
Page 488 For example, to allow callers to place Unscreened Transfers to extensions 301-399, for key 3 enter UTRF for the Action and XXX for the corresponding Number. Electra Elite IPK II Programming Manual 2 - 453...
Page 489 Document Revision 1 Electra Elite IPK II To have Unscreened Transfer call a specific extension, the corresponding Number option should be that extension’s number. The caller then dials that single digit to reach the extension. For example, to have caller’s dial 8 to reach extension 303, for key 8 enter UTRF for the Action and 303 for the corresponding Number.
Page 490 When an Automated Attendant caller presses a key assigned to this action, IPK II In-Mail says “Goodbye” and immediately hangs up. Number Option There is no entry required in the corresponding Number Option. Electra Elite IPK II Programming Manual 2 - 455...
Page 491 Document Revision 1 Electra Elite IPK II GOTO Action - Go to Mailbox (7) (GOTO) Use this option to provide Automated Attendant callers with the ability to route to Call Routing and Announcement Mailboxes. For example, a caller can dial a digit for Sales, and then go to the Call Routing or Announcement Mailbox that provides the dialing options and instructions for Sales.
Page 492 #, they hear, “Please enter the mailbox number. Or, to exit, press the pound key.” Pause Entry : P (Entered by pressing LK4) Use the P option when you want the Automated Attendant to pause while dialing. Electra Elite IPK II Programming Manual 2 - 457...
Page 493 Document Revision 1 Electra Elite IPK II Conditions None Defaults Dial Action Table Default Settings Dial Action Table 1 Dial Action Tables 2~16 UTRF to XXX (Unscreened Transfer to user-dialed (Undefined) extension) (Undefined) (Undefined) UTRF to XXXX (Unscreened Transfer to user-dialed...
Page 494: Master Directory Mailbox Options
1 = UTRF Screened Transfer Timeout 0~255 Time Limit for Dialing Timeout 0~99 Fax Detection 0 = Disable 1 = Enable Next Call Routing Mailbox 0~16 Conditions None Feature Cross Reference Voice Mail Electra Elite IPK II Programming Manual 2 - 459...
Page 495: Routing Directory Mailbox Options
Document Revision 1 Electra Elite IPK II Program 47 : In-Mail 47-15 : Routing Directory Mailbox Options Level: Description to define the Routing Directory Mailbox 47-15: Routing Directory Mailbox Options Options. This data will be referred if Program 47-07-02 (Routing Master Mailbox Type) was set to Type 4 (Directory).
Page 496: Program 50 : Common Channel Interoffice Signaling Service
Level: Description Use Program 50-01 : CCIS System Setting to set the availability of CCIS in the Electra Elite IPK II. All other CCIS settings will not function if this program is disabled. P r o g r a m...
Page 497: Connecting System Settings
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-02 : Connecting System Settings Level: Description Use Program 50-02 : Connecting System Settings to define the settings for each CCIS Route ID. Input Data...
Page 498 If 56K K-CCIS is used, 24 Multi-Frame (ESF) must be assigned in Program 10-03-02. DPC must be what the OPC is on the opposite side of the link. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 463...
Page 499: Ccis Destination System Settings
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-03 : CCIS Destination System Settings Level: Description Use Program 50-03 : CCIS Destination System Settings to assign remote system IP Network information. Input Data...
Page 500: Ccis Office Code Assignment
(up to 4 digits) 0~9 No Setting Conditions This program is only used in an Open Numbering Plan network. This should include the Trunk Access Code and Office Code number. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 465...
Page 501: Ccis Maximum Call Forwarding Hop Counter
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-05 : CCIS Maximum Call Forwarding Hop Counter Level: Description Use Program 50-05 : CCIS Maximum Call Forwarding Hop Counter to define the maximum hop counter of call forwarding.
Page 502: Ccis Feature Availability
If this data is turned to Switching (for message 1 = Enable 0, Day/Night mode will receiver side) not be changed even if system receives Switching message from center. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 467...
Page 503: Ccis Centralized Billing Center Office
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-07 : CCIS Centralized Billing Center Office Level: Description Use Program 50-07 : CCIS Centralized Billing Center Office to define the Point Code and CCIS Route ID for the Billing Center Office.
Page 504: Ccis Centralized Blf Sending Group Assignment
0~16367 Define the Point Code Destination Point Code of Billing Center Office. CCIS Route ID Define the CCIS Route ID to send Billing Center Office. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 469...
Page 505: Ccis Centralized Blf Sending Extension Number Assignment
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-09 : CCIS Centralized BLF Sending Extension Number Assignment Level: Description Use Program 50-09 : CCIS Centralized BLF Sending Extension Number Assignment to define the extension number for sending BLF messages. One...
Page 506 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 471...
Page 507: Ccis Centralized Blf Interval Time Assignment
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-10 : CCIS Centralized BLF Interval Time Assignment Level: Description Use Program 50-10 : CCIS Centralized BLF Interval Time Assignment to define the interval time of sending BLF messages.
Page 508: Ccis Centralized Day/Night Switching Sending Group Assignment
0~16367 Define the Point Code Destination Point Code for Day/Night Switching. CCIS Route ID Define the CCIS Route ID to send Day/ Night Switching messages. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 473...
Page 509: Ccis Centralized Day/Night Mode To System Mode Assignment
Document Revision 1 Electra Elite IPK II Program 50 : Common Channel Interoffice Signaling Service 50-12 : CCIS Centralized Day/Night Mode to System Mode Assignment Level: Description Use Program 50-12 : CCIS Centralized Day/Night Mode to System Mode Assignment to define corresponding night mode to switch to when Day/Night mode switching message arrives.
Page 510: Ccis Centralized Response Timeout Assignment
Use Program 50-13 : CCIS Response Timeout Assignment to define the response timer value. Input Data Item Item Input Data Default IAI Response Timer 0~99 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 475...
Page 511 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 476 Program 50 : Common Channel Interoffice Signaling Service...
Page 512: Program 80 : Basic Hardware Setup For System
0~255 (0 = until On-Hook) Unit Number Item Item Input Data Basic Tone Number 1~33 0 = No Tone 33=Default Time Slot Duration Count 1~255 (100~25500ms) Gain Level (dB) 1~63 (-15.5 ~ +15.5) Electra Elite IPK II Programming Manual 2 - 477...
Page 513: Table 2-8 Basic Tones
Document Revision 1 Electra Elite IPK II Table 2-8 Basic Tones Basic Level Basic Frequency (Hz) Frequency (Hz) Level (dB) Tone No. (dB) Tone No. - 13 520 / 650 -13 / -19 650 / 780 -13 / -19 780 / 1040...
Page 514 Basic 6 38 (+3dB) 26 (-3dB) 38 (+3dB) 26 (-3dB) 14 (-9dB) 32 (0dB) Door Box Chime 3 Basic 6 38 (+3dB) 26 (-3dB) 38 (+3dB) 26 (-3dB) 14 (-9dB) 32 (0dB) Electra Elite IPK II Programming Manual 2 - 479...
Page 515 Document Revision 1 Electra Elite IPK II Service Repeat Unit Basic Gain Level Tone Service Tone Duration Count Count Tone No. (dB) Basic 6 38 (+3dB) Door Box Chime 4 26 (-3dB) 38 (+3dB) 26 (-3dB) 14 (-9dB) 32 (0dB)
Page 516 32 (0dB) External Call Waiting Tone External Executive Override 32 (0dB) Tone --- Not Used --- Basic 1 32 (0dB) Generate tone for TAPI2.1 Warning Beep Tone Signaling Basic 1 32 (0dB) Electra Elite IPK II Programming Manual 2 - 481...
Page 517 Document Revision 1 Electra Elite IPK II Service Repeat Unit Basic Gain Level Tone Service Tone Duration Count Count Tone No. (dB) Basic 5 32 (0dB) Headset Ear Piece Ringing Tone 32 (0dB) 32 (0dB) 32 (0dB) 32 (0dB) Opening Chime Tone,...
Page 518: Dtmf Tone Setup
Item Item Input Data Default Duration 1~255 5 (100 ms) Pause 1~255 Tone Level (Low) (dB) 1~97 65 (-13dB) Tone Level (High) 1~97 69 (-11dB) Duration Pause Electra Elite IPK II Programming Manual 2 - 483...
Page 519 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference None 2 - 484 Program 80 : Basic Hardware Setup for System...
Page 520: Dtmf Tone Receiver Setup
DTMF Tone Receiver Type No. 1 = DTMF Receiver for Extension 2 = DTMF Receiver for Trunk 3 = --- Reserve --- 4 = --- Reserve --- 5 = --- Reserve --- Electra Elite IPK II Programming Manual 2 - 485...
Page 521 Document Revision 1 Electra Elite IPK II Item Item Input Data Detect Level 0 = 0dBm ~ -25dBm 1 = -5dBm ~ -30dBm 2 = -10dBm ~ -35dBm 3 = -15dBm ~ -40dBm 4 = -20dBm ~ -45dBm 5 = -25dBm ~ -50dBm...
Page 522 ON detect time 1 (30ms) 1 (30ms) 1 (30ms) 1 (30ms) 1 (30ms) OFF detect time 1 (30ms) 1 (30ms) 1 (30ms) 1 (30ms) 1 (30ms) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 487...
Page 523: Call Progress Tone Detector Setup
Document Revision 1 Electra Elite IPK II Program 80 : Basic Hardware Setup for System 80-04 : Call Progress Tone Detector Setup Level: Description to define the various levels Program 80-04 : Call Progress Tone Detector Setup and timers for the Call Progress Tone Detector.
Page 524 ON max. time 14(450ms)[ET] (1230ms) OFF min. time 1 (60ms) 9(300ms) 83 (2520ms) OFF max. time 1 (60ms) 14(450ms) 115 (3480ms) --- Reserve --- --- Reserve --- Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 489...
Page 525: Date Format For Smdr And System
Document Revision 1 Electra Elite IPK II Program 80 : Basic Hardware Setup for System 80-05 : Date Format for SMDR and System Level: Description to define the date format when Program 80-05 : Date Format for SMDR and System printing out the SMDR, alarm report, and system information, etc.
Page 526: Program 81 : Basic Hardware Setup For Trunk
Default Wait time for Physical activation 1~255 (200~5100 ms) 100 (20 sec) (Timer 3) Detection time for Physical 1~255 (200~5100 ms) 5 (1 sec) deactivation Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 491...
Page 527: Isdn Bri & Pri Layer 2 (T-Point) Initial Data Setup
Document Revision 1 Electra Elite IPK II Program 81 : Basic Hardware Setup for Trunk 81-05 : ISDN BRI & PRI Layer 2 (T-Point) Initial Data Setup Level: Description to define the Program 81-05 : ISDN BRI & PRI Layer 2 (T-Point) Initial Data Setup various basic data for layer 2 of ISDN BRI and PRI.
Page 528: Isdn Bri & Pri Layer 3 (T-Point) Timer Setup
120 (sec) T317 1~(T316-1) 60 (sec) T318 1~254 (sec) 4 (sec) T319 1~254 (sec) 4 (sec) 1~254 (sec) 30 (sec) T320 T321 1~254 (sec) 30 (sec) T322 1~254 (sec) 4 (sec) Electra Elite IPK II Programming Manual 2 - 493...
Page 529 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference ISDN Compatibility 2 - 494 Program 81 : Basic Hardware Setup for Trunk...
Page 530: Coi Initial Data Setup
15 = release of a CO/PBX line after a disconnect (0 = No Setting) signal is received from the distant CO or PBX. Pause Time Selection 1~15 (500~7500 ms) (200 ms) Electra Elite IPK II Programming Manual 2 - 495...
Page 531 Document Revision 1 Electra Elite IPK II Hookflash Time Selection 1 0 = 20 ms (600 ms) 1 = 40 ms 2 = 60 ms 3 = 80 ms 4 = 100 ms 5 = 140 ms 6 = 160 ms...
Page 532: Tie Line Initial Setup
(130 ms~1950 ms) (390 ms) from another system is detected before the (0 = No Setting) acknowledge signal is sent out. [Delay] [Delay] 1~15 (90 ms) (30 ms~450 ms) (0 = No Setting) Electra Elite IPK II Programming Manual 2 - 497...
Page 533 Document Revision 1 Electra Elite IPK II Loop Off-Guard Time Selection (0.5 sec~2.0 sec) (2.0 sec) Assign loop off-guard time to prevent noise 5~15 that could cause the system to be unable to (3 sec~13 sec) answer an incoming Tie line.
Page 534 9 = 600 ms 10 = 800 ms 11 = 1.0 seconds 12 = 1.5 seconds 13 = 2.0 seconds 14 = 3.0 seconds 15 = 5.0 seconds Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 499...
Page 535: Trunk Gain Level Data Setup
Document Revision 1 Electra Elite IPK II Program 81 : Basic Hardware Setup for Trunk 81-12 : Trunk Gain Level Data Setup Level: Description to define the various initial data for Program 81-12 : Trunk Gain Level Data Setup TLI/DTI/DID/BRT/PRT package.
Page 536: Program 82 : Basic Hardware Setup For Extension
1 = High 2 = Mid 3 = Low Item Item Input Data = 520Hz Frequency 1 = 540Hz Frequency 2 = 660Hz = 760Hz = 1100Hz = 1400Hz = 2000Hz Electra Elite IPK II Programming Manual 2 - 501...
Page 537 Document Revision 1 Electra Elite IPK II Item Item Input Data Modulation = No Modulation = 8Hz Modulation = 16Hz Modulation = Envelope Default Incoming Ringing Tone Tone Frequency 1 Frequency 2 Modulation Number Type Pattern 1 High 1100 1400...
Page 538: Dss Console Led Pattern Setup
ACD Emergency Call LED Pattern 0 : [OFF] LED Pattern 1 : [FL: On(500ms)/Off(500ms)] LED Pattern 2 : [WK: On(250ms)/Off(250ms)] LED Pattern 3 : [RW: On(125ms)/Off(125ms)] LED Pattern 4 : [IR: On(125ms)/Off(125ms)/On(125ms)/Off(625ms)] Electra Elite IPK II Programming Manual 2 - 503...
Page 539 Document Revision 1 Electra Elite IPK II LED Pattern 5 : [IL: On(875ms)/Off(125ms)] LED Pattern 6 : [IW: On(625ms)/Off(125ms)/On(125ms)/Off(125ms)] LED Pattern 7 : [ON] Conditions None Feature Cross Reference Direct Station Selection (DSS) 2 - 504 Program 82 : Basic Hardware Setup for Extension...
Page 540: Sidetone Volume Setup
-36 (dB) -18 (dB) -30 (dB) -12 (dB) -24 (dB) -12 (dB) -18 (dB) -12 (dB) -12 (dB) Conditions None Feature Cross Reference Central Office Calls, Answering Central Office Calls, Placing Electra Elite IPK II Programming Manual 2 - 505...
Page 541: Sli Initial Setup
Document Revision 1 Electra Elite IPK II Program 82 : Basic Hardware Setup for Extension 82-11 : SLI Initial Setup Level: Description Use Program 82-11 : SLI Initial Setup to define the various timers for SLI Packages. Input Data Item...
Page 542: Opx Initial Data
HookFlash End Time Specify the maximum hookflash 0 = HST+0ms 1~15=HST+100ms~HST+1500ms duration from a Single Line Telephone (HST=Hookflash Start Time) to receive a second dial tone. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 507...
Page 543 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 508 Program 82 : Basic Hardware Setup for Extension...
Page 544: Program 83 : Hardware Setup For Ipk Ii Wireless
Encryption = Disabled 1 (Enabled) = Enabled This program enables (1) or disables (0) encryption for the phone when placing and receiving calls. Conditions None Feature Cross Reference Wireless-DECT Electra Elite IPK II Programming Manual 2 - 509...
Page 545: Wireless Dect Measurement
Document Revision 1 Electra Elite IPK II Program 83 : Hardware Setup for IPK II Wireless 83-12 : Wireless DECT Measurement Level: Description (This program is available only via telephone programming and not through PC Programming). to define the Wireless DECT Base Program 83-12 : Wireless DECT Measurement Station measurement.
Page 546: Program 84 : Hardware Setup For Voip
IP Terminals and Adapters. P r o g r a m Input Data term Terminal Type 1 = D IP / Electra Elite IPK II Multiline Terminal with IP Adapter 2 = Soft Phone 3 = Bundle IP Phone Item Item...
Page 547 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) 2 - 512 Program 84 : Hardware Setup for VoIP...
Page 548: Program 84 : Hardware Setup For Voip
Program 84-04 : VoIP DHCP Server Mode Setup server on the CPU II( )-U10. Input Data Item Item Input Data Default DHCP Server Mode = Disable = Enable Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 513...
Page 549: Voip Ip Address
Document Revision 1 Electra Elite IPK II Program 84 : Hardware Setup for VoIP 84-05 : VoIP IP Address Level: Description to define the IP Address of the IP Program 84-05 : VoIP Address Setup Applications (MG16 ETU, CCISoIP ETU).
Page 550 The system programming must be exited before these program options to take affect. When configuring the CCISoIP IP Application the IAD(8)-U10 ETU must be reset for system data to take affect. Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 515...
Page 551: Voip Info
Document Revision 1 Electra Elite IPK II Program 84 : Hardware Setup for VoIP 84-06 : VoIP Info Level: Description to set up threshold levels of the MG16 ETU. Program 84-06 : VoIP Info Input Data Slot Number 01~24 Item...
Page 552 Electra Elite IPK II Document Revision 1 Conditions The system programming must be exited before these program options take affect. Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 517...
Page 553: Vlan Setup
Document Revision 1 Electra Elite IPK II Program 84 : Hardware Setup for VoIP 84-09 : VLAN Setup Level: Description (For Future Release) to setup the VLAN data. Program 84-09 : VLAN Setup Input Data Item Item Input Data Default...
Page 554: Tos Setup
1 = Low Reliability Low Cost 1 = Optimize for low cost 0 = Normal Cost routing 1 = Low Cost Priority (D.S.C.P- 0~63 DSCP (Differentiated Differentiated Services Services Code Point) Code Point) Electra Elite IPK II Programming Manual 2 - 519...
Page 555 Document Revision 1 Electra Elite IPK II Conditions The system needs to be reset in order for these program options to take affect. Feature Cross Reference Voice Over Internet Protocol (VoIP) 2 - 520 Program 84 : Hardware Setup for VoIP...
Page 556: Dip Codec Information Basic Setup
G.729 Jitter Buffer 0~500 ms Type G.729 Jitter Buffer 0~500 ms --- Not Used --- --- Not Used --- --- Not Used --- --- Not Used --- --- Not Used --- Electra Elite IPK II Programming Manual 2 - 521...
Page 557 Document Revision 1 Electra Elite IPK II Item Item Default Description Input Data Jitter Buffer Mode = Static = Immediate VAD Threshold 0~30 (-19db~+10db, Adaptec Threshold) = Adaptec Threshold = -19db(-49dbm) 20 = 0db (-30dbm) 29 = 9dbm(-21dbm) 30 = 10dbm(-20dbm)
Page 558 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 523...
Page 559: Ccis Over Ip Codec
Document Revision 1 Electra Elite IPK II Program 84 : Hardware Setup for VoIP 84-21 : CCIS over IP CODEC Level: Description to set the various CCIS over IP CODEC Program 84-21 : CCIS over IP CODEC parameters. Input Data...
Page 560 30 = +10dbm (-20dbm) Echo Canceller Mode 0 = Disable 1 = Enable NLP Echo Canceller Mode 0 = Disable 1 = Enable 0 = Disable UDP Checksum Mode 1 = Enable Electra Elite IPK II Programming Manual 2 - 525...
Page 561 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) 2 - 526 Program 84 : Hardware Setup for VoIP...
Page 562: Program 85 : Hub(8) Lan Setup
0 = Disable 85-01-01 - Disable, Duplex 85-03-01 - Half Duplex 1 = Enable When enabled, a switch applies back pressure to a half-duplex ingress port while an output queue is congested. Electra Elite IPK II Programming Manual 2 - 527...
Page 563 Document Revision 1 Electra Elite IPK II Flow Control, Full-Duplex 0 = Disable Full Duplex - 802.3x 85-01-01 - Disable 1 = Enable 85-03-01 - Full Duplex When enabled, a switch applies flow control to a full-duplex ingress port while an output queue is congested.
Page 564: Hub(8) Vlan Setup
1~4095 Port 3 VLAN ID 1~4095 Port 4 VLAN ID 1~4095 Port 5 VLAN ID 1~4095 Port 6 VLAN ID 1~4095 Port 7 VLAN ID 1~4095 Port 8 VLAN ID 1~4095 Electra Elite IPK II Programming Manual 2 - 529...
Page 565 Document Revision 1 Electra Elite IPK II Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) 2 - 530 Program 85 : HUB(8) LAN Setup...
Page 566: Priority Setup
TX High When Program 85-03- 01 is set to "High", untagged frames are marked with this priority setting. Previously tagged frames are unchanged. Electra Elite IPK II Programming Manual 2 - 531...
Page 567 Document Revision 1 Electra Elite IPK II TX Low When Program 85-03- 01 is set to "Low", untagged frames are marked with this priority setting. Previously tagged frames are unchanged. Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP)
Page 568: Port Mirroring Setup
Target Port Set to the port where the protocol analyzer is connected. Conditions Set to the port where the protocol analyzer is connected. Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 533...
Page 569: Hub(8) Vlan Group Settings
Document Revision 1 Electra Elite IPK II Program 85 : HUB(8) LAN Setup 85-05 : HUB(8) VLAN Group Settings Level: Description (For Future Release) to define the VLAN group setup for Program 85-05 : HUB(8) VLAN Group Settings each HUB(8) ETU.
Page 570 Electra Elite IPK II Document Revision 1 Conditions None Feature Cross Reference Voice Over Internet Protocol (VoIP) Electra Elite IPK II Programming Manual 2 - 535...
Page 571 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 536 Program 85 : HUB(8) LAN Setup...
Page 572: Program 90 : Maintenance Program
P r o g r a m Item Item Input Data Default Year 00~99 0 (No Setting) Month 01~12 0 (No Setting) 01~31 0 (No Setting) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 537...
Page 573: Programming Password Setup
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-02 : Programming Password Setup Level: Description to set the system passwords. For Program 90-02 : Programming Password Setup password entry purposes, the system allows eight users to be defined. Each user can...
Page 574 --- Not Used --- --- Not Used --- --- Not Used --- --- Not Used --- Conditions More than one extension can be in the programming mode. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 539...
Page 575: Save Data
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-03 : Save Data Level: Description (This program is available only via telephone programming and not through PC Programming). to save the programmed data on the SRAM and Flash Program 90-03 : Save Data ROM to the 16M/32M ATA removable Compact Flash memory card.
Page 576: Load Data
After uploading the programming, reset the system and wait a few minutes for the system to reset completely before accessing any lines or special system features. Otherwise, some unusual LED indications may be experienced. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 541...
Page 577: Slot Control
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-05 : Slot Control Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 90-05 : Slot Control to reset or delete (uninstall) circuit boards (slots 1~24).
Page 578: Trunk Control
Input Data Menu Number 0 = Set Busy Out 1 = Reset/Release Busy Out (idle) Item Item Input Data Trunk Control Trunk Port Number: 001~200 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 543...
Page 579: Extension Control
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-07 : Extension Control Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 90-07 : Extension Control is used for the extension maintenance.
Page 580: System Reset
After restoring a customer database, the system must be reset using Program 90- 08 or by powering down/powering up before all the restored programming will take affect. Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 545...
Page 581: Automatic System Reset Time
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-09 : Automatic System Reset Time Level: Description Use Program 90-09 : Automatic System Reset Time to define the time the system will automatically reset. Input Data Item No.
Page 582: System Alarm Setup
Remove and reinstall Error or the ETU is defective. the ETU. If RECover message is received in the alarm report, the ETU is good. If not, replace with a new ETU. Electra Elite IPK II Programming Manual 2 - 547...
Page 583 Document Revision 1 Electra Elite IPK II Is Used To Alarm TYPE Report Note Action Advise of . . . 2 (MIN) Board Installation ETU was unplugged Check the ETU Error without using the installation. proper procedure. 2 (MIN) Communication...
Page 584 Check the printer for full. the SMDR. CS Blocking CS Error Information 1 CS Transmission Error CSIU Dch Error CSIU Transmission Error CS Error Information 2 VM/HD Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 549...
Page 585: System Alarm Report
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-11 : System Alarm Report Level: Description Use Program 90-11 : System Alarm Report to define the details of the system alarm report. Input Data Item Item Input Data...
Page 586 Up to 255 Characters No Setting When alarm reports are to be EMailed, enter a name which will be used to identify the particular system. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 551...
Page 587: System Alarm Output
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-12 : System Alarm Output Level: Description Use Program 90-12 : System Alarm Output to set the options for the alarm report. This program has 6 separate menu options. Define the output port to be used as the output for system alarm report and set the system alarm options.
Page 588: System Information Output
Output Command Dial 1 + press HOLD (Press HOLD key to cancel.) Dialing 1 from this program sends the system report to the connected device. Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 553...
Page 589: Main Software Information
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-16 : Main Software Information Level: Description Use Program 90-16 : Main Software Information to display the main software information on the CPUII. Main software information can also be viewed outside of system programming by pressing FEATURE and the 3 key on any multiline terminal.
Page 590: Dial Block Release
Input Data Extension Number Up to 8 digits Item Item Input Data Dial Block Release [Release?] : Dial 1+ press HOLD (Press HOLD to cancel.) Conditions None Feature Cross Reference Code Restriction Electra Elite IPK II Programming Manual 2 - 555...
Page 591: Traffic Report Data Setup
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-20 : Traffic Report Data Setup Level: Description Use Program 90-20 : Traffic Report Data Setup to define the details of the traffic report. Input Data Item Item...
Page 592: Traffic Report Output
Input Data Default Output Port Type 0 = No Setting 1 = COM port (CPUII) 2 = USB port (CPUII) 3 = LAN Port (CPUII) Conditions None Feature Cross Reference Traffic Reports Electra Elite IPK II Programming Manual 2 - 557...
Page 593: Deleting Registration Of Ip Telephones
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-23 : Deleting Registration of IP Telephones Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 90-23 : Deleting Registration of IP Telephones to delete the registered IP telephone from the system.
Page 594: System Alarm Report Notification Time Setup
Use Program 90-24 : System Alarm Report Notification Time Setup to set up when the alarm report will print. Input Data Notification Number 1~12 Item Item Input Data Default Month 00~12 (00=Disabled) 00~31 Hour 00~23 Minute 00~59 Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 559...
Page 595: System Alarm Report Cc Mail Setup
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-25 : System Alarm Report CC Mail Setup Level: Description Use Program 90-25 : System Alarm Report CC Mail Setup to define the mail address to receive the system alarm report CC Mail setup.
Page 596: Program Access Level Setup
(located in 2 = IN Level the upper left corner at the 3 = SA Level beginning of each program). 4 = SB Level Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 561...
Page 597: Wireless Dect System Id
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-27 : Wireless DECT System ID Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 90-27 : Wireless DECT System ID to define the DECT System ID.
Page 598: Dim Access Over Ethernet
Item Item Input Data Default Access Enabling 0 = Disable 0 (Disable) 1 = Enable 20 characters ASPIRE Username (alphanumeric) 20 characters 12345678 Password (alphanumeric) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 563...
Page 599: Firmware Information
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-34 : Firmware Information Level: Description Use Program 90-34 : Firmware Information to list the package type and firmware ETUs installed in the system. Input Data Slot No.
Page 600: Wizard Programming Level Setup
0 = All 1 = SB (System Administrator B) 2 = SA (System Administrator A) 3 = IN (Installer) 4 = MF (Manufacturer) 5 = DEV (Developer) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 565...
Page 601: Firmware Update Time Setting
Document Revision 1 Electra Elite IPK II Program 90 : Maintenance Program 90-36 : Firmware Update Time Setting Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 90-35 : Firmware Update Time Setting to define the data for the firmware update feature.
Page 602 Update failed. Drive 'A' (Compact Flash) was not available. Update Fail Update failed. The file “main.up” does not exist on drive 'A'. Update Fail Update failed. The scheduled time has expired. Sample Report Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 567...
Page 603 Document Revision 1 Electra Elite IPK II THIS PAGE INTENTIONALLY LEFT BLANK 2 - 568 Program 90 : Maintenance Program...
Page 604: Program 91 : Ipk Ii Wireless Dect Ps Entry
Program 91-06 : DECT Obtaining Access Rights is used when registering an Electra Elite IPK II Wireless DECT phone to the system. You can select the port number to which the new phone will be subscribed, or you can enter “0” to have the system automatically assign an available port.
Page 605 The display shows IPEI?. The IPEI (International Portable Equipment Identity) is a unique number embedded into each Electra Elite IPK II Wireless DECT phone. Enter the IPEI number for the Electra Elite IPK II Wireless DECT telephone or enter as a wild character and the system will automatically retrieve the number for the phone being set up.
Page 606 Press HOLD and register another telephone if required or continue with the next step. Prior to deleting an Electra Elite IPK II Wireless DECT phone from the system using Program 91-07-01 : DECT Deleting Access Rights, make sure the DSIU ETU is installed in the system.
Page 607: Dect Deleting Access Rights
Use Program 91-07 : DECT Deleting Access Rights to remove an Electra Elite IPK II Wireless DECT phone from the system. Prior to deleting an Electra Elite IPK II Wireless DECT phone from the system, make sure the DSIU ETU is installed in the system. If the DSIU is removed when Program 91-07-01 is run, the system will retain the DECT setting.
Page 608: Program 92 : Copy Program
If the information is only be copied to one extension, trunk, group, etc., enter the information entered in the Destination Number (From) entry. Electra Elite IPK II Programming Manual 2 - 573...
Page 609 Document Revision 1 Electra Elite IPK II Copy Program is applicable only for the following programs. Trunk Port Base Program Program Name Note 14-01 Trunk Basic Data Setup Copy all data except Trunk Name (Item 01). 14-02 Analog Trunk Data Setup...
Page 610 Copy all data except Group Name (Item 01). 35-04 SMDR Port Assignment for Department Group DSS Console Base Program Program Name Note 30-01 DSS Console Operation Mode 30-03 DSS Key Assignment Electra Elite IPK II Programming Manual 2 - 575...
Page 611 Document Revision 1 Electra Elite IPK II Door Box Base Program Program Name Note 32-02 Door Box Ring Assignment Conditions Using this program to copy a multiline terminal’s Programmable Function Keys will copy all the keys whether they exist on the phone to which the programming is being copied.
Page 612: Delete All Extension Numbers
However, the extension number of the first port is not deleted. Input Data Extension No. Delete Yes: 1 [Dial 1]+Hold key (Only press Hold key is canceled) Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 577...
Page 613: Copy Program By Port Number
Document Revision 1 Electra Elite IPK II Program 92 : Copy Program 92-03 : Copy Program by Port Number Level: Description (This program is available only via telephone programming and not through PC Programming). Use Program 92-03 : Copy Program by Port Number to delete all extension numbers.
Page 614: Extension Data Swap
Use Program 92-04 : Extension Data Swap to swap two extension’s data. Item Item Input Data 1st Extension Number Up to 8 characters. 2nd Extension Number Conditions None Feature Cross Reference None Electra Elite IPK II Programming Manual 2 - 579...
Page 615: Extension Data Swap Password
Document Revision 1 Electra Elite IPK II Program 92 : Copy Program 92-05 : Extension Data Swap Password Level: Description Use Program 92-04 : Extension Data Swap Password to define the 4-digit password for each extension to allow Extension Data Swap.
Page 617 R O G R A M M I N G A N U A L N E C U n i f i e d S o l u t i o n s , I n c . D o c u m e n t R e v i s i o n 1...

NEC Electra Elite IPK II Programming Manual

Chapter 1 Introduction

Quick Links

Related Manuals for NEC Electra Elite IPK II

Summary of Contents for NEC Electra Elite IPK II