Panasonic DH-3ND1 Operating Instructions Manual page 27

9. Shower Head can be set at various positions.
For DH-3ND1, DH-3NDP1
(a) Loosen Shower Hanger Knob and Shower Hanger can be adjusted higher or lower position.
Tighten Shower Hanger Knob.
(b) Loosen Shower Hanger Knob and Shower Hanger can be adjusted to the left or right position.
Tighten Shower Hanger Knob.
(c) The angle of Shower Head can be adjusted by moving the Shower Head upward and downward.
For DH-3NDP1 (with Rain Shower) only
10. Shower Head can be set at various positions:
(a) Push and hold the Shower Hanger Button to adjust higher or lower and left or right.
Release the Shower Hanger Button to fix position.
(b) The angle of Shower Head can be adjusted by moving the Shower Head upward or downward.
11. Rain Shower can be set at various positions:
(a) Loosen the Adjustable Lock and adjust the Upper Shower Pipe higher or lower and left or right.
Tighten the Adjustable Lock.
When setting the Upper Shower Pipe at maximum height, lower down the pipe a bit if feel a jerk
followed by tightening the Adjustable Lock (this is to avoid leaking due to exceed the maximum
height setting).
(b) The angle of Rain Shower Head can be adjusted by moving the Rain Shower Head upward or downward.
Note:
When turning OFF the Home Shower, remaining water from the Shower Head/ Rain Shower Head
may continue to drip before it stop completely.
12. e-Cycle Setting.
(a) e-Cycle must be operated after the set is ON (hot shower will flow out of the
Shower Head/Rain Shower Head).
(b) (1) Firstly, press the e-Cycle Button to start operate the e-Cycle function.
(2) e-Cycle Button has several options that can be selected.
Every selection will be displayed at the e-Cycle area at the LCD Display follow by
indication of "HOT" and "COOL" alternately blinking.
(3) By subsequently pressing the e-Cycle Button, the cycle condition will vary. Please refer to figures below.
(i)
Health
AM
(iii)
Health
Hot
Cool
Short
Note: During HOT Shower
During COOL Shower
(4) • When the e-Cycle operate, the area for clock at the LCD Display will change to the
number of cycle to indicate every complete cycle of hot shower and cool shower in
e-Cycle. e.g.:
• During usage of e-Cycle, the cycle count continues even when resetting the HOT
shower and COOL shower temperatures.
(5) If you would like to change COOL temperature:
a) Pressing and holding the "SET" Button for 3 seconds
(during this action, the clock is blinking).
b) There are 4 options of cool temperature. The option will vary by pressing
subsequently the "-" and "+" Button.
Every selection will be displayed at Temperature Indicator area.
Note: When the power on, the cool temperature becomes "PO"
(same as inlet water temperature).
Normal
• e-Cycle OFF
Safe
• Normal hot shower
o
C
Max
• Short cycle of
Safe
e-Cycle Shower
• Indicate as "Short"
o
C • HOT Shower: 30 s
Max
COOL Shower: 20 s
and will blink.
and will blink.
=> 1 cycle of hot and cool shower.
- 27 -
Short
Long
(ii)
Health
Hot
o
Cool
C
Normal
Max
(iv)
Health
Hot
o
Cool
C
Max
Long
(a) (b)
11 (a)
11 (b)
Safe
Health
Hot o
Cool C
Normal Bubble
Max
PM Level Beat
e-Cycle - Set + e-Hybrid
10 (b)
ELB Test
Push On -Off
ELB Reset
Push Up
10 (a)
• Normal cycle of e-Cycle
Safe
Shower
• Indicate as "Normal"
• HOT Shower: 40 s
COOL Shower: 30 s
• Long cycle of e-Cycle
Safe
Shower
• Indicate as "Long"
• HOT Shower: 50 s
COOL Shower: 40 s
Health
Hot
o
Cool
C
Normal
Max
- +
Set
- +
Set
(c)