Makita LM001J Instruction Manual
Cordless lawn mower
Hide thumbs
Also See for LM001J:
- Instruction manual (145 pages) ,
- Instruction manual (100 pages) ,
- Instruction manual (143 pages)
Related Manuals for Makita LM001J
Summary of Contents for Makita LM001J
- Page 1 INSTRUCTION MANUAL Cordless Lawn Mower LM001J LM002J Read before use. Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: LM001J LM002J Mowing width (blade diameter) 480 mm 534 mm No load speed Normal mode 3,200 min 2,800 min Soft no-load mode 2,500 - 3,200 min 2,300 - 2,800 min Noise reduction mode 2,500 min 2,300 min Part number of replacement... -
Page 3: General Power Tool Safety Warnings
Use personal protective equipment. Always SAFETY WARNINGS wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions General power tool safety warnings will reduce personal injuries. Prevent unintentional starting. Ensure the WARNING: switch is in the off-position before connecting Read all safety warnings, instruc-... - Page 4 Disconnect the plug from the power source Service and/or remove the battery pack, if detachable, Have your power tool serviced by a qualified from the power tool before making any adjust- repair person using only identical replacement ments, changing accessories, or storing power parts.
- Page 5 14. Do not touch blades and other hazardous Always wear protective goggles to protect moving parts while they are still in motion. This your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in reduces the risk of injury from moving parts. the USA, EN 166 in Europe, or AS/NZS 1336 15.
- Page 6 Avoid using the mower in bad weather con- 24. Do not start the mower when standing in front ditions especially when there is a risk of of the discharge opening. lightning. 25. If the mower starts to vibrate abnormally Wear eye protection and stout shoes at all (check immediately) times while operating the mower.
- Page 7 Battery tool use and care Service Recharge only with the charger specified by Have your power tool serviced by a qualified the manufacturer. A charger that is suitable for repair person using only identical replacement one type of battery pack may create a risk of fire parts.
-
Page 8: Installing The Handle
Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. Tips for maintaining maximum Fig.1... -
Page 9: Removing The Mulching Plug
Turn the knob 90° while pulling the knob on the Lift up the mulching plug slightly, and then remove lower handle to release the locking pin. Perform the same procedure on the other side. Raise the handle, and then turn the knob on both sides 90°. Make sure that the knobs are securely fixed. - Page 10 Make sure that there is no sagging on the corners Installing or removing the grass of the grass basket. basket To install the grass basket, follow the steps below. Open the rear cover. Fig.7 Open the upper clip, and attach it to the frame. Fig.10 ►...
-
Page 11: Functional Description
Attaching the mulching plug FUNCTIONAL DESCRIPTION Open the rear cover, and then remove the grass basket. Installing or removing battery cartridge CAUTION: Always switch off the machine before installing or removing of the battery cartridge. CAUTION: Hold the machine and the battery cartridge firmly when installing or removing bat- tery cartridge. -
Page 12: Overload Protection
Hold the battery cartridge in the upright position Insert the lock key in the place shown in the figure with the indicator lamps facing forward. Insert the bat- as far as it will go. tery cartridge into the machine until it is latched with the battery lock lever. -
Page 13: Overheat Protection
Let the machine and battery(ies) cool down. If no improvement can be found by restoring protection The control panel has the main power switch and the system, then contact your local Makita Service Center. mode switching button. Indicating the remaining battery... -
Page 14: Main Power Switch
This mower is equipped with the lock key and handle switch. If you notice anything unusual with either of the lock key or switch, stop the operation immediately and have them checked by your nearest Makita Authorized Service Center. Install the battery cartridge. Insert the lock key, and then close the battery cover. -
Page 15: Adjusting The Handle Height
The table below shows the relationship between the When the grass basket is almost full, the indicator does number on the mower body and the approximate mow- not float while the blades are running. In this case, stop ing height. the operation immediately and empty the basket. -
Page 16: Electronic Function
• Electric brake This machine is equipped with an electric brake. If the machine consistently fails to quickly stop the mower blades after releasing the switch lever, have the machine serviced at Makita Authorized Service Center. OPERATION Fig.27 Mowing ► 1. Knob... -
Page 17: Emptying The Grass Basket
Firmly hold the handle with both hands when mowing. Mowing a long-grass lawn The mowing speed guideline is approximately 7 to 14 meters per 10 seconds. Do not try to cut long grass all at once. Instead, mow the lawn in steps. Leave a day or two between mowings until the lawn becomes evenly short. -
Page 18: Maintenance
Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Maintenance Remove the lock key and battery cartridge, and then close the battery cover. - Page 19 Turn the knob 90° while pulling the knob on the Loosen the thumb nuts on both sides, and then lower handle to release the locking pin. Perform the fold the upper handle as shown in the figure. same procedure on the other side, and then fold the handle.
- Page 20 Removing or installing the mower blade NOTICE: When installing the mower blade, make sure that the protrusions on the blade support fit in the holes in the mower blade. WARNING: The blade coasts for a few sec- onds after releasing the switch. Do not start any Installing the mower blade operation until the blade comes to a complete stop.
-
Page 21: Troubleshooting
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to disassemble the machine. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. - Page 24 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885922B926 www.makita.com 20210817...