Advertisement
Quick Links
Advertisement
Related Manuals for AEG A18F10FN
Summary of Contents for AEG A18F10FN
- Page 1 A18F10FN A18F10FNNZ Original instructions...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modifications.
- Page 3 1. Jam-clearing mechanism 9. Belt clip 2. Depth-of-drive adjustment 10. Rear loading magazine 3. No-mar pad 11. Trigger mode selector (for A18F10FN only) 4. Pusher 12. LED light 5. Rafter hook 13. Battery port 6. Switch trigger 14. Hex key 7.
- Page 5 START A18HPI BHPV18 A18F10FN...
- Page 6 Remove the battery pack before starting any work on the machine. click...
- Page 7 78-100 % 55-77 % 33-54 % 10-32 % <10 %...
- Page 8 Remove the battery pack before starting any work on the machine.
- Page 9 click NOTE: Squeeze the grip switch (1) to activate the nailer whenever the battery has been removed and replaced, or when the product enters its inactive mode. The LED (2), located on the rear base of the nailer, will glow green once activated.
- Page 10 START When marks to material or surfaces are unwanted in straight nailing applications the no-mar pad can be used. Remove the no-mar pad for skew nailing and general framing. A18F10FN The bump fire feature is not available for A18F10FNNZ.
- Page 11 Remove the battery pack before starting any work on the machine.
- Page 12 If a jam occurs, the product will automatically enter a jam mode and reset the driver blade. The LED, located on the rear base of the nailer, will flash red. Remove the battery pack. Check to ensure that the product is free from a jammed fastener.
- Page 15 Extended magazine AFNEM (001700007)
- Page 16 A18HPI BHPV18 After the initial use, you may notice a decrease in performance. Refilling the air pressure tank to 125 psi can help restore the unit’s performance.
- Page 17 Connect an inflator/air compressor to the valve and pressurise the tank to a maximum of 125 psi. Allow the tool to recharge for approximately 30 seconds. Type of air chuck required: Compatible with Schrader Valve with 0.305”-32TPI thread NOTE: It is normal to hear a hissing sound while the tank is being refilled.
-
Page 18: Nailer Safety Warnings
Diameter 2. 9 to 3.3 mm Length min./max 50/90 mm Recommended Cycle rate 500/hr Burst cycle rate (A18F10FN) – bump fire mode 3 / second Burst cycle rate (A18F10FNNZ) 2 / second Magazine capacity 67 nails (3.06 mm diameter) Fastener range... -
Page 19: Specified Conditions Of Use
Do not dispose of used battery packs in the household refuse or Do not drive nails near edge of material. The workpiece may split by burning them. AEG Distributors offer to retrieve old batteries to causing the nail to ricochet, injuring you or a coworker. Be aware protect our environment. -
Page 20: Maintenance
■ Do not transport batteries that are cracked or leak. need to be replaced which have not been described, please contact Check with forwarding company for further advice. one of our AEG service agents (see our list of guarantee/service addresses). BATTERY PACK PROTECTION If needed, an exploded view of the tool can be ordered. -
Page 21: Troubleshooting
Fastener length Wear eye protection Keep hands away Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE... - Page 24 31 Gilby Road, Mount Waverley, VIC, 3149, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand AEG is a registered trade mark used under license from AB Electrolux (publ). 961096765-01 © 2021 Techtronic Cordless GP.