Makita HM001G Instruction Manual
Cordless demolition hammer
Hide thumbs
Also See for HM001G:
- Instruction manual (124 pages) ,
- Instruction manual (21 pages) ,
- Instruction manual (100 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita HM001G
Summary of Contents for Makita HM001G
- Page 1 INSTRUCTION MANUAL Cordless Demolition Hammer HM001G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: HM001G Blows per minute 0 - 2,650 min Rated voltage D.C. 36 V - 40 V max Overall length with BL4025 481 mm with BL4040 496 mm Net weight 6.3 - 7.1 kg • Due to our continuing program of research and development, the specifications herein are subject to change without notice. •... -
Page 3: Ec Declaration Of Conformity
Electrical safety Vibration Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any The vibration total value (tri-axial vector sum) deter- adapter plugs with earthed (grounded) power mined according to EN60745-2-6: tools. Unmodified plugs and matching outlets will Work mode: chiselling function with side grip reduce risk of electric shock. - Page 4 Do not let familiarity gained from frequent use Keep handles and grasping surfaces dry, clean of tools allow you to become complacent and and free from oil and grease. Slippery handles and ignore tool safety principles. A careless action can grasping surfaces do not allow for safe handling and cause severe injury within a fraction of a second.
- Page 5 12. Use the batteries only with the products WARNING: DO NOT let comfort or familiarity specified by Makita. Installing the batteries to with product (gained from repeated use) replace non-compliant products may result in a fire, exces- strict adherence to safety rules for the subject sive heat, explosion, or leak of electrolyte.
- Page 6 Keep the wireless unit away from young chil- dren. If accidentally swallowed, seek medical 26. Do not insert any devices other than Makita attention immediately. wireless unit into the slot on the tool. Use the wireless unit only with Makita tools.
-
Page 7: Functional Description
Indicating the remaining battery capacity FUNCTIONAL DESCRIPTION Press the check button on the battery cartridge to indi- cate the remaining battery capacity. The indicator lamps light up for a few seconds. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge CAUTION: Always switch off the tool before... -
Page 8: Overheat Protection
Overheat protection Speed change When the tool or battery is overheated, the tool stops automatically. In this case, let the tool and battery cool before turning the tool on again. NOTE: When the tool is overheated, the lamp blinks. Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. Switch action WARNING: Before installing the battery car- tridge into the tool, always check to see that the ► 1 . Speed adjusting dial switch trigger actuates properly and returns to the "OFF"... -
Page 9: Side Handle
Lighting up the front lamp NOTICE: Do not install the side handle / side grip to any other area than the designated mounting area. ► 1 . Lamp CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. - Page 10 Side grip (auxiliary handle) To remove the bit, pull the chuck cover down all the way and pull the bit out. The side grip can be swung, allowing easy handling of the tool in any position. Loosen the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by turning clockwise. ► 1 . Bit 2. Chuck cover Bit angle ► 1 . Side grip The bit can be secured at 12 different angles. To Installing or removing bit change the bit angle, slide the change ring forward, then turn the change ring to change the bit angle.
- Page 11 Attach the holder joint to the tool, and then attach Dust extractor attachment the hose holder (C) to the holder joint. Optional accessory Install the hose holder (A/B). When the side handle is installed to tool, loosen the clamp nut, and then remove the hex bolt. Install the hose holder (A) between the hex bolt and the clamp nut by tightening the clamp nut firmly. ► 1 . Hex bolt 2. Hose holder (A) 3. Clamp nut ► 1 . Holder joint 2. Hose holder (C) When the side grip is installed to the tool, loosen the side grip, mount the hose holder (B) to the shaft, and then tighten the side grip firmly.
-
Page 12: Operation
Connect the hose to the hose of the vacuum Chipping/Scaling/Demolition cleaner with the hose joint. NOTE: If the hose is not included, attach the dust Hold the tool firmly with both hands. Turn the tool on and apply slight cover to the cleaner's joint or attach it to Makita's pressure on the tool so that the tool will not bounce around, uncon- hose ø28. trolled. Pressing very hard on the tool will not increase the efficiency. Adjust the distance between the dust cover and the tip of the chisel or bull point. - Page 13 To use the wireless activation function, prepare follow- Insert the wireless unit to the slot and then close ing items: the lid. • A wireless unit (optional accessory) When inserting the wireless unit, align the projections • A vacuum cleaner which supports the wireless with the recessed portions on the slot. activation function The overview of the wireless activation function setting is as follows.
- Page 14 3 seconds until the wireless activation cleaner lamp blinks in green. And then press the wireless acti- vation button on the tool in the same way. NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration. NOTE: Finish installing the wireless unit to the tool before starting the tool registration.
- Page 15 Connect the hose of the vacuum cleaner with the Pull the switch trigger of the tool. Check if the tool. vacuum cleaner runs while the switch trigger is being pulled. To stop the wireless activation of the vacuum cleaner, push the wireless activation button on the tool. NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2 hours. In this case, set the stand-by switch on the...
- Page 16 Description of the wireless activation lamp status ► 1 . Wireless activation lamp The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the meaning of the lamp status. Status Wireless activation lamp Description Color Duration...
- Page 17 If the cancellation is performed successfully, the wire- Cancelling tool registration for the less activation lamps will light up in red for 2 seconds vacuum cleaner and start blinking in blue. NOTE: The wireless activation lamps finish blinking in Perform the following procedure when cancelling the red after 20 seconds elapsed. Press the wireless acti- tool registration for the vacuum cleaner.
- Page 18 Troubleshooting for wireless activation function Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The wireless activation lamp does The wireless unit is not installed into the tool. Install the wireless unit correctly. not light/blink. The wireless unit is improperly installed into the tool. The terminal of the wireless unit and/or Gently wipe off dust and dirt on the terminal of the the slot is dirty.
-
Page 19: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. - Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885832B220 www.makita.com 20210223...