Makita DVC660 Instruction Manual page 17

When using ø28 mm dust extraction
hose
1. Attach the front cuff to the hose for dust extraction.
When connecting the front cuff, make sure that it is
securely screwed on the hose.
2. Connect the front cuff to the tool's extraction
outlet.
► Fig.24: 1. Front cuff 2. Extraction outlet 3. Hose
The front cuff can be detached by turning it counter-
clockwise while holding the hose.
When using ø38 mm hose with front
cuff 38
1. Twist and insert the joint or the front cuff to the
inlet part on the hose, depending on the tool that you
are going to connect.
2.
Connect the front cuff to the tool's extraction
outlet.
► Fig.25: 1. Joint 2. Front cuff 3. Extraction outlet
4. Hose
To remove the joint and the front cuff, follow the installa-
tion procedures in reverse.
Attaching bent pipe assembly
Optional accessory
NOTE: You don't need to perform this procedure
if your model comes with the bent pipe assembly
attached to the hose.
NOTE: There are two types of bent pipe assembly;
the one for slide-type extension wand and the one for
ring-type extension wand. If you prepare the bent pipe
assembly, choose the one for your desired extension
wand type.
The bent pipe assembly is used for connecting the
extension wand or nozzle for vacuum cleaning to this
product.
If you want to use this product as the vacuum cleaner,
attach the bent pipe assembly to the hose.
To attach, unscrew the front cuff from the hose and
fasten the sleeve of bent pipe assembly onto the hose.
To remove, loosen the sleeve of bent pipe assembly
from the hose.
► Fig.26: 1. Hose 2. Bent pipe assembly 3. Sleeve
Installing filter bag / dust bag
Optional accessory
CAUTION:
Do not use a damaged filter bag.
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust
or particles may be exhausted from the cleaner
and they may cause respiratory disease to the
operator.
Install either dust bag or filter bag before using cleaner.
— Dust bag are usable many times repeatedly by
cleaning it out.
— Filter bag is a throw-away type. Throw away the
entire filter bag without emptying when it has
become full.
NOTICE:
When the filter bag is already full,
replace with new one. When the dust bag is
already full, empty it. Continuous use with the filter
bag/dust bag full results in reduced suction power.
NOTICE:
To prevent dust from getting into the
motor:
Make sure that the filter bag/dust bag is
—
installed before use.
— Do not use a broken or ripped bag.
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the filter bag/dust bag.
NOTICE:
The filter bag/dust bag for the cleaner
is an important component for maintaining the
appliance performance. Using non-genuine filter
bag/dust bag may cause smoke or ignition.
NOTE: When the filter bag/dust bag is not installed in
the cleaner, the front cover does not close completely.
► Fig.27
1. Unlock the latch by lifting the bottom side. Push
the grooved area to lift the front latching side. Pull the
latch to open the lid.
► Fig.28: 1. Hook 2. Lid
2. Insert the filter bag into the slit on the upper side of
the room as illustrated.
► Fig.29: 1. Slit 2. Filter bag
When using the dust bag, insert the brim of the dust bag
into the slit.
► Fig.30: 1. Slit 2. Brim 3. Dust bag
3. Align the hole of the filter bag with the hose cuff
and push the cardboard portion to the end. Make sure
that the rubber ring on the filter bag goes over the rim
on the hose cuff.
► Fig.31: 1. Rubber ring on the filter bag 2. Rim on
the hose cuff 3. Cardboard portion of the
filter bag 4. Hose cuff
17 ENGLISH