Page 1
Installation Guidelines Directives d’installation 5000-02-2557-MAN VERSION B...
Page 2
IMPORTANT The way the Camoplast Hi-Performance Tracks UTV T4S track system is used, is directly linked with the longevity of the system components. Sportive driving, rapid direction changes and repeated fast turns (more specifically on power steering vehicles) are not advised. This way of driving increases the risk of derailing and can cause premature wear and or major breakdowns on the track system which will not be covered under normal warranty.
Page 3
Page 3 Installation Guidelines / Directives d’installation FRONT ANCHOR BRACKET PARTS LIST / LISTE DE PIÈCES - ANCRAGE AVANT Figure 1 ITEM DESCRIPTION 1004-02-0100 FRONT BRACKET KIT / ENSEMBLE ANCRAGE AVANT 1004-02-0101 ANTI-ROTATION FRONT BRACKET / ANCRAGE ANTIROT. AV. 1006-02-0105 FRONT BRACKET COVER / COUVERT ANCRAGE AVANT 1033-10-0055 HEX BOLT / BOULON HEX - HCS, M10-1.5X55, 8.8, ZP, DIN931 1074-10-0001 NYLON NUT / ÉCROU NYLON - FNN, M10-1.5, 8, ZP, DIN6926...
Page 7
Page 7 Installation Guidelines / Directives d’installation PREPARATION / PRÉPARATION WARNING AVERTISSEMENT Do not place any part of your body under the Ne jamais exposer des parties du corps sous le vehicle unless it is securely placed on appropriate véhicule à moins que celui-ci ne repose sur des stands.
Page 9
Page 9 Installation Guidelines / Directives d’installation 5. Position the bottom part of the anchor bracket 5. Positionner la partie inférieure de l’ancrage (7-8) underneath the lower suspension arm. anti–rotation (7-8) sous le bras de suspension Position the top part (9-10) over the suspension inférieur.
Page 11
Page 11 Installation Guidelines / Directives d’installation 7. Attach the stabilizing rod (B) to the anchor 7. Fixer le bras stabilisateur (B) au boulon déjà bracket (A), using the long spacer bushing (C), installé sur l’ancrage de suspension (A) à l’aide the short spacer bushing (D), flat washer (E) and de l’espaceur long (C), l’espaceur court (D), de nut (F).
Page 13
Page 13 Installation Guidelines / Directives d’installation 5. Position the bottom part of the anchor bracket 5. Positionner la partie inférieure de l’ancrage (2) underneath the lower suspension arm. anti–rotation (2) sous le bras de suspension Position the top part (3) over the suspension inférieur.
Page 15
Page 15 Installation Guidelines / Directives d’installation 9. Verify that spring assembly bolt (F) is tightened 9. Vérifier que le boulon du ressort (F) est serré au to the recommended torque specification: 40 couple recommandé : 40 N•m [30 lb•pi]. Voir la N•m [30 lb•ft].
Page 17
Page 17 Installation Guidelines / Directives d’installation 12. Assemble the aluminium puck of the steering 12. Assembler l’extrémité en aluminium du limiteur limiter assembly with the front anchor bracket de conduite au trou central de la partie inférieure using the steering limiter mounting bolt (D), de l’ancrage avant en utilisant le boulon (D) washer (E) and nut (F).
Page 19
Page 19 Installation Guidelines / Directives d’installation COMPLETION / COMPLÉTER L’INSTALLATION 1. Verify the suspension settings. If the shock 1. Vérifier l’ajustement de la suspension, si les absorbers are adjustable, they should be adjusted amortisseurs sont réglable, ils doivent être réglés to the firmest level in order to allow for maximum au niveau le plus ferme afin de permettre un clearance between the system and the fender of the...