Installing or removing X-LOCK wheel
WARNING:
Never actuate the release lever of
the X-LOCK holder during operation. Make sure
that the X-LOCK wheel has stopped completely
when removing it. Otherwise, the X-LOCK wheel
comes off from the tool and may cause serious injury.
CAUTION:
Use only original X-LOCK wheels
with the X-LOCK logo. This tool is dedicated to
X-LOCK.
The maximum clamping gauge of 1.6 mm can only be
guaranteed with original X-LOCK wheels.
Use of any other wheels may lead to insecure clamp-
ing, and cause the clamp tool to come loose.
CAUTION:
Do not touch the X-LOCK wheel
immediately after operation. It may be extremely
hot and could burn your skin.
CAUTION:
Make sure that the X-LOCK wheel
and holder of the tool are not deformed and are
free from dust or foreign matters.
CAUTION:
Do not put your finger near the
holder while installing or removing the X-LOCK
wheel. It may pinch your finger.
CAUTION:
Do not put your finger near the
release lever while installing the X-LOCK wheel. It
may pinch your finger.
NOTE: No additional parts such as inner flanges
or lock nuts are required to install or remove the
X-LOCK wheels.
1.
To install the X-LOCK wheel, make sure that both
catches are in the unlocked position.
If not, push the release lever from A side to lift B
side, then pull the release lever from B side as
illustrated. The catches are set in the unlocked
position.
► Fig.12: 1. Catch 2. Release lever
2.
Place a central position of the X-LOCK wheel on
the holder.
Make sure the X-LOCK wheel is parallel to the
flange surface and with the correct side facing up.
3.
Push the X-LOCK wheel into the holder. The
catches snap into the lock position with a click and
fix the X-LOCK wheel.
► Fig.13: 1. X-LOCK wheel 2. Holder 3. Flange sur-
face 4. Catch
4.
Make sure the X-LOCK wheel is fixed correctly.
The surface of the X-LOCK wheel is no higher
than the surface of the holder as shown in the
figure.
If not, the holder must be cleaned or the X-LOCK
wheel must not be used.
► Fig.14: 1. Surface of the holder 2. Surface of the
X-LOCK wheel
To remove the X-LOCK wheel, push the release lever
from A side to lift B side, then pull the release lever from
B side as illustrated.
The X-LOCK wheel is released and can be removed.
► Fig.15: 1. Release lever
Installing or removing dust cover attachment
Optional accessory
CAUTION:
Always be sure that the tool is
switched off and unplugged before installing or
removing the dust cover attachment. Failure to do
so causes damage to the tool or a personal injury.
There are three types of dust cover attachment and
each is used in one of different positions.
► Fig.16: 1. Marking A
► Fig.17: 1. Marking B
► Fig.18: 1. Marking C
Place the dust cover attachment so that the side of the dust cover
attachment with the marking (A, B or C) faces towards the tool
head. Snap the hooks of the dust cover attachment in the vent.
► Fig.19: 1. Hook 2. Vent
Dust cover attachment can be removed by hand.
NOTICE:
Clean out the dust cover attachment when it
is clogged with dust or foreign matters. Continuing opera-
tion with a clogged dust cover attachment will damage the tool.
OPERATION
WARNING:
It should never be necessary to
force the tool. The weight of the tool applies ade-
quate pressure. Forcing and excessive pressure
could cause dangerous wheel breakage.
WARNING:
ALWAYS replace wheel if tool is
dropped while grinding.
WARNING:
NEVER hit the workpiece with the wheel.
WARNING:
Avoid bouncing and snagging the
wheel, especially when working corners, sharp
edges etc. This can cause loss of control and kickback.
WARNING:
NEVER use tool with wood cutting
blades and other saw blades. Such blades when
used on a grinder frequently kick and cause loss of
control leading to personal injury.
WARNING:
Never actuate the release lever of
the X-LOCK holder during operation. An X-LOCK wheel
comes off from the tool and may cause serious injury.
WARNING:
Make sure that an X-LOCK wheel
is fixed firmly.
CAUTION:
Never switch on the tool when it
is in contact with the workpiece, it may cause an
injury to operator.
CAUTION:
Always wear safety goggles or a
face shield during operation.
CAUTION:
After operation, always switch off
the tool and wait until the wheel has come to a
complete stop before putting the tool down.
CAUTION:
ALWAYS hold the tool firmly with
one hand on housing and the other on the side
grip (handle).
12 ENGLISH