Advertisement
IF MAIN BURNER WILL NOT COME ON WITH
CALL FOR HEAT
1. Make sure gas control knobs are in the ON position.
2. Adjust thermostat several degrees above room
temperature.
3. Using an ac voltmeter, check for 24V at the gas
control.
• If pilot lights, measure across MV/PV and MV.
• If pilot does not light, measure across MV/PV and
PV before safety lockout occurs.
4. If no voltage is present, check control circuit for
proper operation.
5. If 24V is present, replace the entire gas control.
INSTRUCTIONS TO THE USER
FOR YOUR SAFETY, READ BEFORE LIGHTING
!
WARNING
IF YOU DO NOT FOLLOW THE
WARNINGS BELOW AND THE LIGHTING
INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION CAN RESULT WITH
PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
Follow these warnings exactly:
1. Pilot flame is lit automatically. Do not light the
pilot flame manually.
2. Before lighting pilot burner flame, smell around
the appliance for gas. Be sure to smell next to
the floor because LP gas is heavier than air.
3. IF YOU SMELL GAS:
• Turn off the gas supply at the appliance
service valve. On LP gas systems, turn off
gas supply at the gas tank.
• Do not light any appliances.
• Do not touch electrical switches or use the
phone.
• Leave the building and use a neighbor's
phone to call your gas supplier.
• If you can not reach your gas supplier, call
the fire department.
4. Do not force the gas control knob. Use only
your hand to push down or turn the gas control
knob. Never use any tools. If the gas control
knob will not operate by hand, call a qualified
service technician to replace the entire gas
control. Force or attempted repair can result in
a fire or explosion.
5. Call a qualified service technician to replace
the entire gas control if it has been flooded
with water.
6. Replace the entire gas control in the event of
any physical damage, tampering, bent termi-
nals, missing or broken parts, stripped threads,
or evidence of exposure to heat.
Home and Building Control
Honeywell Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
69-0814—1
Printed in U.S.A.
IMPORTANT: Follow the operating instructions pro-
TO TURN ON THE APPLIANCE
STOP: READ THE WARNING ABOVE
manually light the pilot. If the appliance does not turn on
when the thermostat is set several degrees above room
temperature, follow these instructions:
safety control.
to OFF.
then smell gas, STOP! Follow step 3 in the Warning in the
Instructions To The User section. If you do not smell gas,
continue with the next step.
wise
knobs to OFF, turn off the upstream appliance valve, and
contact a qualified service technician for assistance.
TURNING OFF THE APPLIANCE
VACATION SHUTDOWN: Set the thermostat to the de-
COMPLETE APPLIANCE SHUTDOWN: Turn both gas
ance valve and connect the power supply; then follow the
procedure above.
Home and Building Control
Honeywell Limited—Honeywell Limitée
740 Ellesmere Road
Scarborough, Ontario
M1P 2V9
8
vided by the manufacturer of your heating appliance.
The information below will be of assistance in a
typical control application, but the specific controls
used and the procedures outlined by the manufac-
turer of your appliance may differ, and require spe-
cial instructions.
The pilot flame is lit automatically. Do not attempt to
1. Set the thermostat to its lowest setting to reset the
2. Disconnect all electric power to the appliance.
3. Remove the gas control access panel.
4. Turn both of the gas control knobs clockwise
5. Wait five minutes to clear any unburned gas. If you
6. Turn both of the gas control knobs counterclock-
to ON.
7. Replace the gas control access panel.
8. Reconnect all electric power to the appliance.
9. Set the thermostat to the desired setting.
10. If the appliance does not turn on, set the gas control
sired room temperature while you are away.
control knobs clockwise
Turn off the upstream appliance valve and disconnect
power supply. Appliance will be completely shut off.
To resume normal operation, turn on the upstream appli-
Helping You Control Your World
to OFF. Do not force.
QUALITY IS KEY
Advertisement
