Makita UN460WD Instruction Manual
Cordless pole hedge trimmer
Hide thumbs
Also See for UN460WD:
- Instruction manual (108 pages) ,
- Instruction manual (108 pages) ,
- Instruction manual (93 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita UN460WD
Summary of Contents for Makita UN460WD
- Page 1 INSTRUCTION MANUAL Cordless Pole Hedge Trimmer UN460WD Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: UN460WD Blade length 460 mm Strokes per minute 3,600 min Cutting blade angle 135° (up 60°, down 75°) Overall length 1,889 - 2,511 mm Rated voltage D.C. 10.8 V - 12 V max Net weight 2.8 - 3.0 kg •... -
Page 3: Ec Declaration Of Conformity
Vibration Applicable standard : EN62841-4-2 Left hand (Front grip) Right hand (Rear grip) (m/s Uncertainty K (m/s (m/s Uncertainty K (m/s 2.5 m/s or less 2.5 m/s or less NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another. - Page 4 Dress properly. Do not wear loose clothing or Keep cutting tools sharp and clean. Properly jewellery. Keep your hair and clothing away maintained cutting tools with sharp cutting edges from moving parts. Loose clothes, jewellery or are less likely to bind and are easier to control. long hair can be caught in moving parts.
-
Page 5: Additional Safety Instructions
In the event of an emergency, switch off Cordless Pole Hedge Trimmer the tool and remove the battery cartridge Safety Warnings immediately. DANGER - Keep hands away from blade. Keep all parts of the body away from the blade. Contact with blade will result in serious personal Do not remove cut material or hold material injury. - Page 6 Only use the tool for its intended purpose. Do Do not charge battery in rain, or in wet not use the tool for any other purpose. locations. Switch off the tool and remove the battery Do not charge the battery outdoors. cartridge before: Do not handle charger, including charger plug, and charger terminals with wet hands.
- Page 7 It will Do not expose battery cartridge to water also void the Makita warranty for the Makita tool and or rain. charger. A battery short can cause a large current...
-
Page 8: Parts Description
PARTS DESCRIPTION Head Angle adjustment button Lock-lever Thumb nut Front grip Rear grip Battery cartridge Switch trigger Lock-off button Shear blades FUNCTIONAL DESCRIPTION CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. -
Page 9: Adjusting The Cutting Angle
Never use the tool if it starts when you pull the switch trigger without pressing the lock-off button. Ask your local Makita Service Center for repairs. ► 1. Head 2. Angle adjustment button WARNING: Never disable the lock function or tape down the lock-off button. - Page 10 Adjusting the pipe length ASSEMBLY CAUTION: Always be sure that the tool is CAUTION: Always be sure that the tool is switched off before adjusting the pipe length. switched off and the battery cartridge is removed CAUTION: When adjusting the pipe length, before carrying out any work on the tool.
- Page 11 Prepare the crank and new shear blades. Adjust the crank so that the 2 small holes on the crank are lined up on the alignment line as shown in the figure. ► 1. Crank 2. Shear blades Remove the blade cover, and then attach it to the new shear blades.
- Page 12 Remove the blades and install them again. NOTICE: If the parts other than the shear blades such as the crank are worn out, ask Makita Authorized Service Centers for parts replacement or repairs. Installing or removing the chip...
-
Page 13: Operation
NOTICE: NOTICE: Never try to remove the chip receiver Do not cut down dead trees or similar by an excessive force with its claws locked in the hard objects. Doing so may damage the tool. grooves of the shear blades. NOTICE: Do not trim the grass or weeds while using the shear blades. -
Page 14: Cleaning The Tool
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 14 ENGLISH... -
Page 15: Troubleshooting
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885883-223 www.makita.com 20210126...