Table of Contents
Advertisement
Programming
Pressing 2 will select user Programming Mode which may only be accomplished by an authorized person. After pressing 2, a screen will
prompt for a password. After entering the correct password, the user may select from a list of programming options.
Pressing 3 will select FS-Tools Up/Download which allows the user to enable the remote programming option. Refer to "FS-Tools
Upload/Download" on page 119.
Pressing 4 will select USB Up/Download which allows the user to upload or download FACP programming via the USB port. See "USB
Upload/Download" on page 121.
The down arrow which appears in the display indicates that additional programming choices can be viewed by pressing the down arrow
key on the keypad. If a down and up arrow appear in the display, pressing the 'down' arrow key will display the subsequent Program-
ming Screens as illustrated below while pressing the 'up' arrow key will display the previous screen.
Pressing the down arrow displays the following screen:
Pressing 1, while this screen is being displayed, allows the user to upgrade the panel software. Refer to "Firmware Upgrade" on
page 123.
Exit Programming and Read Status
The programmer can exit any mode by repeatedly pressing the keypad ESC (Escape) key until the display reads System Normal. Note
that the data which is entered during Programming mode is not saved until the programmer exits this mode by repeatedly pressing the
'ESC' key. If the Reset key is pressed or power is lost before exiting Programming mode, all data just entered will be lost.
User Programming Levels
There are two user programming levels:
•
User Master Program Level 1 is used for programming panel specific data relating to device types, zoning, messages, control panel
functions, etc.
•
User Maintenance Program Level 2 is used by a qualified operator to access features such as Disable/Enable, View and Clear
History, Walktest, and System Time Change.
3.3 Initial Power-up
The following sections describe the initial programming procedures for a new system. The same procedures are used to modify program-
ming in an existing system.
After completing the wiring of addressable devices to the SLC, apply power to the control panel. If the addressable devices have not yet
been programmed into the FACP, their LEDs will not flash and the following trouble message will be displayed.
3.4 Programming Screens Description
The options available when the Enter key is pressed are: Read Status, Programming. The Read Status and Programming options have
multiple functions or features which may be chosen. To view all of the choices, it is necessary that the programmer scroll through a num-
ber of additional subscreens. These selections are displayed on multiple screens to make them more readable for the programmer. Refer
to "Master Programming Level" on page 49, for additional information on the various screens.
The title of the main option screen will always be displayed at the top of the subscreens for the programmer's convenience. If additional
subscreens exist, an Up or Down arrow will be displayed in the upper right corner of the screen being viewed. The programmer can then
press the keypad Up or Down arrow key to view the new subscreen. To select one of the choices in a screen, the programmer presses the
keypad numerical key corresponding to the desired choice.
Note that subscreens may also have multiple options which require viewing more than one screen. The same process, as detailed in the
previous paragraphs, is followed to view all option choices.
3.5 Programming and Passwords
There are two factory set programming passwords which will access the Programming screens as indicated in the following examples.
From either of the screens, access to specific system and device features or programming may be obtained. All user programming entries
are stored in nonvolatile memory. The factory set passwords can be changed by the user as described in "Password Change" on page 95.
If an invalid password in entered, the blinking cursor will return to the first password character position. To exit Programming or Read
Status mode at any time, press the ESC (Escape) key repeatedly. Note that Programming mode must be exited using the ESC key in order
to store the program data entered during this mode. If the Reset key is pressed or power is lost before exiting Programming mode, the
data just entered will not be saved.
48
1=FIRMWARE UPGRADE
TROUBL IN SYSTEM
NO DEVICES INSTALLED
09:03A 080516
NFW-50X Manual — P/N LS10129-001NF-E:C 7/25/2018
Initial Power-up
Advertisement
Table of Contents
