1. Manuals
  2. Brands
  3. Tripp Lite Manuals
  4. Cable Tester
  5. T100-001-TST
  6. Owner's manual

Tripp Lite T100-001-TST Owner's Manual

Rj11/rj12/rj45 cable crimper/stripper with built-in tester
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
RJ11/RJ12/RJ45 Cable
Crimper/Stripper with
Built-In Tester
Model: T100-001-TST
Este manual esta disponible en español en la página
de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web
de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства
представлена на веб-сайте компании Tripp Lite по
адресу: www.tripplite.com
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate
peace of mind. You could also win an ISOBAR6ULTRA
surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
1
01-154-9337A8-EN.indd 1
1/25/2018 3:14:40 P

Advertisement

Table of Contents
loading

Related Manuals for Tripp Lite T100-001-TST

Summary of Contents for Tripp Lite T100-001-TST

  • Page 1 Register your product for quicker service and ultimate peace of mind. You could also win an ISOBAR6ULTRA surge protector—a $100 value! www.tripplite.com/warranty 1111 W. 35th Street, Chicago, IL 60609 USA www.tripplite.com/support Copyright © 2018 Tripp Lite. All rights reserved. 01-154-9337A8-EN.indd 1 1/25/2018 3:14:40 P...

  • Page 2: Package Includes

    Package Includes • T100-001-TST • Owner’s Manual Product Features • All-in-one crimping tool efficiently cuts and strips LAN cables up to 12 mm in diameter • Multifunctional crimping tool creates all 8P8C, 6P6C and 4P4C plug types • Built-in UTP/STP cable tester quickly and accurately identifies wiring faults in newly crimped or existing in-wall LAN cables up to 600 ft.
  • Page 3 Operation Cutting Cable A single blade for cutting cable is located on the back of the tool. To use, insert the desired cable length into the slot labeled “CUT”. To cut the cable, squeeze the handles together until the cable cleanly separates.
  • Page 4 Operation Testing Uninstalled Cables When testing uninstalled patch cables, the remote unit can remain attached to the base of the main unit’s handle. Connect one end of the cable to be tested to the main unit. Connect the other end of the cable to the remote unit.
  • Page 5 Cable Test Results Pass Indicators: Shield Green SHIELD LED indicates the shield on the cable is correctly and continuously wired through the modular plug termination. Standard Wiring Four green LEDs on pairs 1-2, 3-6, 4-5, and 7-8 indicate all four pairs are terminated correctly. Fail Indicators: A flashing green LED indicates which wire pair(s) have a fault.
  • Page 6 Split pairs occur when the tip (positive conductor) and ring (negative conductor) of two twisted pairs are interchanged. Note: The T100-001-TST will check a fault condition in the above order before detecting other fault conditions. The detection and indication of a fault is handled on a one-per- test basis.
  • Page 7 DEBUG Mode Debug mode allows you to identify which cable pairs have a wiring fault. This mode cycles through each cable pair, displaying a test result for one pair at a time. From the series of LED indicators, the failed pair and fault condition can be identified.
  • Page 8 DEBUG Mode DEBUG Example #1: The cable fault is a short on Pair 3-6, the Debug mode LED series is as follows: • Pair 1-2 will flash green-green as a good pair. • Pair 3-6 will flash green on the PAIR LED followed by a red on the SHORT LED.
  • Page 9 DEBUG Mode DEBUG Example #2: The following are examples of potential LED sequences on Pair 1-2 and possible fault conditions for that pair only. 1st Short 2nd Long Red Fault Flash Flash LEDs Fault Condition No Red LED Good Pair None No Red LED Open Condition...

  • Page 10: Battery Replacement

    Battery Replacement 1. Remove the cover plate to change the batteries. 2. Remove old batteries. 3. Install a new 6-volt A544 1/2AA size battery or 4 LR44 Button Cell batteries. 4. Slide cover plate back into place. 01-154-9337A8-EN.indd 10 1/25/2018 3:14:41 P...

  • Page 11: Warranty And Product Registration

    Warranty and Product Registration 1-Year Limited Warranty Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products.
  • Page 12 Product Registration PRODUCT REGISTRATION Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Table of Contents