Table of Contents
Advertisement
Available languages
Available languages
NOTE: Before starting installation, read all the steps
of these instructions.
Use the illustration beside to identify your kitchen cabinet
type.
This manual covers 2 kinds of installation: the standard
(without EZ1 brackets) and the EZ1 one-person installation
system (using included template and brackets). For the
standard installation, go to page 13.
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as the range hood
width. If the cabinet is greater than 1/2" wider than the range hood width, please use the standard installation method.
1. Use the proper template for vertical OR horizontal
disharge (included) for placement of ductwork and electrical
cutout in cabinet or wall. For a non-ducted installation, DO
NOT cut a duct access hole, only cut the hole for electrical
wiring. If replacing a hood and plan to use the existing
duct and electrical, steps 2 to 5 may not be necessary. If
so, skip to step 6.
2. Measure and mark the hood center line on cabinet bottom.
4. Drill a 1/8" dia. pilot hole for house wiring, at A location
on template.
5. Use a sharp pencil or 1/8" drill bit to mark the locations
for the appropriate duct access holes (16 locations for 7"
round duct, or 4 corner locations for rectangular duct).
Remove the template.
PREPARE THE HOOD LOCATION
EZ1 One-person installation system
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
7" R
OUND
D
UCTING
OR
R
ECTANGULAR
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
scale when installing to framed
C
ONDUIT ROND DE
7
PO
OU
C
ONDUIT RECTANGULAIRE
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
T
ITLE TO BE TRANSLATED IN
S
PANISH
8"
conséquence.
C L
C
O
C
To be translated in Spanish.
ONDUCTO REDONDO
ONDUCTO RECTANGULAR
7
.
DE
PULG
7½"
V RTICAL EX
VERTICAL EXHAUST
A
A
A
10½"
4¼"
14½"
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
C
F
OLD TEMPLATE ALONG GRADUATED
SCALE WHEN INSTALLING TO FRAMED
P
.
CABINET
CENTER LINE
FRAMED CABINET
3. Align the center line on template with the hood center
line marked on the bottom of the cabinet, placing the
edge (where indicated) of the template against back
wall. When using with framed cabinet for vertical exhaust
installation, fold over rear edge of template equal to the
depth of the cabinet frame at the wall (use graduations
on template, C locations on template). Tape the template
in place.
NOTE: When facing the installation, A and B (on
template) must be at right.
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
D
UCTING
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
être du format exact des conduits.
= 3¼" x 10"
= 3¼" x 14"
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
C
Bend template along graduated
scale when installing to framed
cabinet.
= 3¼ po x 10 po
= 3¼ po x 14 po
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
conséquence.
To be translated in Spanish.
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
S
V RTICAL EX
VERTICAL EXHAUST
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
A
B
C
C
CENTER LINE
HORIZONTAL
EXHAUST DUCTING
A
Place this edge against
cabinet bottom.
Appuyer ce bord contre le bas
Electrical access hole center
de l'armoire.
A = single blower hood
B = double blower hood
Apoyar este borde contra
la base del armario.
Centre du trou pour fil
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
C L
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
M
M
ARK WHERE INDICATED
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
Use this template for marking; do not attempt to cut out the ducting hole through it.
FOR THE APPROPRIATE SIZE DUCT OPENING
LE FORMAT DE CONDUIT UTILISÉ
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
R
D
C
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
ECTANGULAR
UCTING
ONDUIT RECTANGULAIRE
le trou pour le conduit à travers le gabarit.
= 3¼" x 10"
= 3¼ po x 10 po
= 3¼" x 14"
= 3¼ po x 14 po
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
être du format exact des conduits.
T
S
ITLE TO BE TRANSLATED IN
PANISH
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
C
ONDUCTO RECTANGULAR
NOTA: To be translated in Spanish.
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
HORIZONTAL EXHAUST
T T
6. Draw the border for the exhaust ducting by linking its
marks (16 for round duct and 4 for rectangular duct), then
cut the opening in the cabinet bottom (vertical exhaust)
or in the wall (horizontal exhaust). Drill the house wiring
hole by using a 1½" hole saw centered with the pilot hole
previously made in 4.
10
FRAMELESS CABINET
VERTICAL
EXHAUST DUCTING
M
ARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
7" R
OUND
D
UCTING
OR
R
ECTANGULAR
D
UCTING
= 3¼" x 10"
= 3¼" x 14"
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
ONDUIT ROND DE
7
PO
OU
C
ONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
T
ITLE TO BE TRANSLATED IN
S
PANISH
8"
C L
C
O
C
ONDUCTO REDONDO
ONDUCTO RECTANGULAR
7
.
= 3¼ pulg. x 10 pulg.
DE
PULG
= 3¼ pulg. x 14 pulg.
7½"
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
A
A
A
S
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
10½"
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
14½"
A
B
C
ELECTRICAL
A
ACCESS HOLE
C
LOCATION (A)
(
IN CABINET BOTTOM
B
A
Electrical access hol
A = single blower ho
B = double blower
Centre du tr
d'alim
ELECTRICAL
ACCESS HOLE
LOCATION (A)
(
)
IN WALL
)
Advertisement
Chapters
Table of Contents
