Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell 10282
Summary of Contents for Honeywell 10282
- Page 1 BLUFTON 52” CEILING FAN MODEL #10282, 10283 Español p. 20 RATED FOR DAMP LOCATIONS Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,...
-
Page 2: Table Of Contents
WELCOME TABLE OF CONTENTS PREPARATION Before beginning the assembly of this product, Care and Maintenance ......2 ensure all parts are present. Compare all parts with Package Contents . -
Page 3: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Blade (5) 2. Downrod 3. Downrod Pin 4. Downrod Clip 5. Yoke Cover 6. Switch Housing Cap 7. Plug Button 8. Blade Arm (5) 9. -
Page 4: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. -
Page 5: Mounting Options
MOUNTING OPTIONS 1. Your fan has 3 mounting options: Fig. 1 • Standard (Fig. 1) • Angle (Fig. 2) • Closemount (Fig. 3) Note: The fans in figures 1 through 3 are not the actual fan in your package, they are representation of the 3 different mounting options. -
Page 6: Mounting Bracket Installation
MOUNTING BRACKET INSTALLATION 4. Turn off the circuit breakers and wall switch leading Fig. 4 to the fan wire leads (Fig. 4). WARNING Failure to disconnect the power supply prior to installation may result in serious injury or death. 5. Loosen all four mounting bracket screws and Fig. -
Page 7: Standard Or Angle Mounting Instructions
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 7. Partially loosen the two set screws in the yoke at Fig. 7 the top of the motor housing (Fig. 7). Set Screw Fig. 8 8. Remove the downrod clip and downrod pin from the downrod (Fig. 8). Downrod Clip Downrod Pin... - Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 10. Slide the downrod into the yoke of the motor Fig. 10 assembly, align the holes, and reinstall the downrod pin and downrod clip. Then retighten the Downrod two set screws (Fig. 10). Downrod Downrod Clip Setscrew Yoke...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 13. Install the ball end of the downrod into the Fig. 13 mounting bracket opening. Align the slot in the ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 13). Slot Mounting WARNING...
-
Page 10: Closemount Instructions
CLOSEMOUNT INSTRUCTIONS 14. Remove the canopy cover from the bottom of the Fig. 14 canopy (Fig. 14). Helpful Hint: The downrod, canopy cover and yoke cover are not used in this type of installation. Canopy Cover Canopy 15. Align the canopy with the holes in the top of motor Fig. -
Page 11: Wiring
WIRING CAUTION Fig. 17 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (Hot) WARNING If house wires are different colors than referred to in White (Neutral) the following steps, consult a professional electrician Bare/Green (Ground) to determine wiring. -
Page 12: Canopy Installation
CANOPY INSTALLATION 19. Lift the canopy up so the partially installed mounting Fig. 19 bracket screws are engaged in the J-slots on each side of the canopy. Rotate the canopy clockwise and install the previously removed mounting bracket screws from Step 5. Tighten all mounting bracket screws. -
Page 13: Blade Installation
BLADE INSTALLATION 20. Remove motor screws and motor blocks from Fig. 19 Fig. 20 underside of the motor assembly. Discard the motor blocks but save the motor screws for blade arm attachment (Fig. 20). Motor Block Motor Screw Motor Screw Motor Block 21. -
Page 14: Light Kit Installation
LIGHT KIT INSTALLATION 23. To install the fan with a light kit: Fig. 23 Remove the three switch housing screws from the switch housing cap. Then connect the single-pin connector from the switch housing to the single-pin connector from the light kit -- white to white and black to black (Fig. -
Page 15: Light Kit
LIGHT KIT INSTALLATION 26. Lift glass bowl into the light kit. Ensure the clips Fig. 26 on inner edge of the light kit slide inside the glass bowl. The glass bowl should snap into place (Fig 26). Clip Light Kit Glass Bowl 27. -
Page 16: Operating Instructions
OPERATING INSTRUCTIONS 29. Use the reverse switch, located on the side of the Fig. 29 fan, to optimize your fan for seasonal performance (Fig. 29). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort. -
Page 17: Replacement Parts List
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 10282 MODEL 10283 PIECE DESCRIPTION PART # PART # Blade Arm... -
Page 18: Troubleshooting
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. Important: Shut off the main power supply before you begin any maintenance tasks. -
Page 19: Limited Lifetime Warranty
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.