Specifications - Makita 3708 Instruction Manual

ENGLISH (Original instructions)
1-1. Lever
1-2. Scale
1-3. Bit protrusion
1-4. Adjusting roller
2-1. Wing bolt
2-2. Graduation
2-3. Trimmer shoe
2-4. Amount of chamfering
2-5. Base
3-1. Loosen
3-2. Tighten
3-3. Hold
4-1. Trimmer shoe
4-2. Base
5-1. Feed direction
5-2. Bit revolving direction
5-3. Workpiece
5-4. Straight guide
7-1. Base
7-2. Wing bolt
7-3. Screws

SPECIFICATIONS

Collet chuck capacity
No load speed (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model 3708,3708F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Explanation of general view
7-4. Screwdriver
8-1. Templet guide
8-2. Convex portions
9-1. Straight bit
9-2. Base
9-3. Templet
9-4. Distance (X)
9-5. Workpiece
9-6. Templet guide 10
11-1. Bolt
11-2. Guide plate
11-3. Straight guide
11-4. Wing nut
12-1. Clamp screw (A)
12-2. Straight guide
12-3. Wing bolt
12-4. Base
12-5. Wing nut
14-1. Wing nut
14-2. Guide plate
14-3. Straight guide
Model
-1
)
Overall length
Net weight
Safety class
) : 80 dB(A)
pA
3708 / 3708F
6 mm or 1/4"
35,000
308 mm
1.3 kg
ENE010-1
Model 3708FC
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
ENF002-2
The noise level under working may exceed 80 dB (A).
Vibration
The vibration total value (tri-axial vector sum) determined
ENG905-1
according to EN60745:
Work mode : rotation without load
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
5
14-4. Center hole
14-5. Bolt
15-1. Wing nut
15-2. Guide plate
15-3. Straight guide
15-4. Center hole
15-5. Bolt
16-1. Nail
16-2. Center hole
16-3. Straight guide
18-1. Clamp screw (A)
18-2. Adjusting screw
18-3. Clamp screw (B)
18-4. Trimmer guide
18-5. Wing bolt
19-1. Workpiece
19-2. Bit
19-3. Guide roller
20-1. Limit mark
21-1. Screwdriver
21-2. Brush holder cap
/II
) : 76 dB(A)
pA
Wear ear protection
) : 2.5 m/s
h
2
3708FC
6 mm or 1/4"
26,000
308 mm
1.3 kg
/II
ENG900-1
2
or less
ENG901-1