Makita DFL083F Instruction Manual page 8

Function
A nti-reset of c ontroller
O v erh eat protec tion
D etec tion of sw itc h
trigger operation w h en
installing battery
Motor f ailure d etec tion
D ouble-h itting d etec tion
Maintenanc e alarm
A larm f or unav ailable
d ata c ommunic ation
( w ith th e tool in c onnec -
tion w ith P C )
I nd ic ation th at d ata c om-
munic ation is av ailable
( w ith th e tool in c onnec -
tion w ith P C )
Adjusting the fastening torque
W h en y ou w is h to d ri v e ma c h ine s c re w s, h e x bolts,
et c . w it h t h e pre d etermine d tor q ue, a d j ust t h e f astening
tor q ue as f ollo w s.
1. F irst remo v e t h e batter y c artri d ge f rom t h e tool.
2. L oosen an d remo v e t h e s c re w t h at se c ures t h e
ring an d lamp c o v er.
Fig.7: 1. S c re w 2. L amp c o v er
3. R otate t h e ring in t h e f ront o f t h e tool b y h an d so
t h at a h ole c an be seen belo w t h e ring.
Fig.8: 1. R ing
4. I nstall t h e batter y c artri d ge in pla c e. P ull t h e
s w it c h trigger an d release it so t h at t h e a d j ust ring
rotates an d t h e h ole be c omes v isible. A n d t h en remo v e
t h e batter y c artri d ge.
Fig.9: 1. A d j ust ring 2. H ole f or a d j ust grip
5. U se an optional a d j ust grip to a d j ust t h e f astening
tor q ue. I nsert t h e pin o f t h e a d j ust grip into t h e h ole
in t h e f ront o f t h e tool. A n d t h en, turn t h e a d j ust grip
c lo c k w ise to set a greater f astening tor q ue, an d c oun-
ter c lo c k w ise to set a smaller f astening tor q ue.
6. A lign t h e y ello w line w it h y our d esire d number on
t h e f astening tor q ue s c ale.
Fig.10: 1. A d j ust grip 2. H ole f or a d j ust grip 3. S c ale
4. Y ello w line
Status of the tool
T h e battery v oltage F lic kers in red and green
d ropped abnormally f or alternativ ely .
some reason, and th e
tool stopped .
T ool' s c ontroller h eated F lic kers in red q uic kly .
up abnormally and th e
tool stopped .
W h en th e battery c ar- F lic kers in red and green
trid ge is installed w ith alternativ ely .
th e sw itc h trigger pulled ,
th e tool stops to av oid
unintentional start.
Motor f ailure h as been F lic kers in red and green
d etec ted . A t th is time, alternativ ely .
tool d oes not w ork.
W h en th e operator L igh ts up in red .
starts to re-f asten an
alread y -f astened sc rew ,
th e tool d etec t it and
stops.
A maintenanc e time h as F lic kers in y ellow .
c ome ac c ord ing to y our
preset number of sc rew s
d riv en.
D ata c annot be F lic kers in y ellow .
ex c h anged betw een th e
tool and P C in spite of
th e c onnec tion.
T h e tool is c onnec ted to F lic kers in green.
P C and d ata c ommuni-
c ation is av ailable.
Status of the LED indicator/beeper
LED indicator
A series of sh ort beeps
A series of sh ort beeps
A series of sh ort beeps
A series of sh ort beeps
A long beep
7. I nsert t h e batter y c artri d ge an d be sure t h at a
f astening tor q ue h as been set up b y using a f astening
tor q ue tester.
8. R otate t h e ring in f ront o f t h e tool an d t h en tig h ten
t h e s c re w to se c ure t h e ring an d lamp c o v er.
NOTE: Numbers on t h e f astening tor q ue s c ale is a
gui d eline to set up y our d esire d f astening tor q ue.
Adjusting no-load speed and
revolution angle etc.
Y ou c an a d j ust t h e no-loa d spee d , number o f turn, et c .
o f t h e tool w it h y our c omputer. I nstall t h e appli c ation
so f t w are in y our c omputer an d c onne c t it to t h e tool w it h
an U S B c able.
Fig.11: 1. U S B c able 2. U S B c o v er 3. U S B port
NOTICE:
Make sure t h at t h e U S B c o v er c lose d
w h en f astening.
NOTE: F or t h e appli c ation so f t w are, please c onta c t
Makita sales representati v e.
8 ENGLISH
Action to be taken
Beeper
R eplac e th e battery w ith
f ully c h arged one.
R emov e th e battery c ar-
trid ge immed iately and
c ool th e tool d ow n.
R elease th e sw itc h
trigger.
A sk y our loc al Makita
S erv ic e C enter f or repair.
– R eset th e alarm w ith th e
applic ation sof tw are.
– R estart th e applic ation
sof tw are and re-c onnec t
th e U S B c able.
–
–
–