Operation; Maintenance - Makita DCL140 Instruction Manual

Problem Examples
Example 1: Only prefilter has been loaded (no filter)
(Fig. 21)
Example 2: Only filter has been loaded (no prefilter)
(Fig. 22)
Example 3: Filter has been loaded in a peeled back state
(Fig. 16)
Example 4: Prefilter's securing lip is not firmly locked into
groove of cleaner housing (Fig. 23)
Reassembly for high performance filter
Connect high performance filter. At this time, make sure to
twist high performance filter so that securing lip is firmly
locked into cleaner unit. (Fig. 24 & 25)
Connect capsule. Align O symbol on capsule with O
symbol on handle and then firmly twist capsule in direction
of arrow until it is secured. (Fig. 26 & 20)
NOTE:
• Always remove dust ahead of time, as suction power
will be reduced if there is too much dust in cleaner.
• Always be sure to check that high performance filter is
loaded correctly prior to using cleaner. If they are not
loaded correctly, dust will get into the motor housing,
and cause motor failure.
If the following examples occur, high performance filter
is not loaded correctly. Reload them correctly to rectify
problem.
Problem Examples
Securing lip of high performance filter is not firmly locked
into groove of cleaner housing. (Fig. 27)

OPERATION

CAUTION:
• To connect attachments, such as nozzle, twist-insert
attachment in direction of arrow to ensure secure
connection during use. To disconnect attachment,
twist-extract also in direction of arrow.
If attachment is twisted in the opposite direction, when
being connected or disconnected, capsule may
become loose. (Fig. 28)
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture, etc.
Nozzle slips on easily. (Fig. 29)
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for cleaning
a floor while standing erect. (Fig. 30)
Corner nozzle
Fit on the corner nozzle for cleaning corners and crevices
of a car or furniture. (Fig. 31)
Corner nozzle +Extension wand (Straight pipe)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
(Fig. 32)
Cleaning without nozzle
You can pick up powder and dust without nozzle. (Fig. 33)

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
Cleaning
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
• Do not blow dust sticking on the cleaner and filters
by air duster. It brings dust into the housing and
causes failure.
• After washing filters, dry them thoroughly before
use. Insufficiently dried filters may cause poor suction
and shorten the service life of the motor.
• After cleaning filters and sponge filter, be sure to
re-install them before use. If you use the cleaner
without filters and sponge filter, dust comes into the
motor housing and cause malfunction.
Cleaner body
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water. Clean
out also the suction opening and filter mounting area.
(Fig. 34)
Filter
Wash the filter in soapy water when it is clogged with dust
and the cleaner power becomes weak. Dry it out
thoroughly before use. (Fig. 35)
Sponge filter
When the sponge filter becomes dirty, clean it as follows.
1. Remove the filter.
2. Pull out the sponge filter from between the pillars.
3. Clean the sponge filter by tapping or washing. If you
wash it, dry it out thoroughly before use.
4. Insert the sponge filter from between the pillars and
set it in the original position. Make sure that each
bottom edge of the pillar holds down the sponge filter,
and there is no gap between the sponge filter and suc-
tion opening. (Fig. 36)
Wall mount for cordless cleaner
Optional accessory
NOTE:
• The screw to mount the holder is not included. Prepare
a screw which fits with the material to screw into.
Attach the wall mount for cordless cleaner to a hard
wooden wall, beam or column, where the wall mount for
cordless cleaner can be firmly secured. Always be sure
that the wall mount for cordless cleaner is securely
attached before hanging the cleaner. (Fig. 37)
CAUTION:
• Do not hang the cleaner to the wall mount violently
or hang other appliances than the cleaner.
13