Related Manuals for Makita DBC340
Summary of Contents for Makita DBC340
- Page 1 Instruction Manual Original Instruction Manual DBC340 Important: Read this instruction manual carefully before putting the brushcutter into operation and strictly observe the safety regulations! Keep this Instruction Manual!
- Page 2 SAFETY PRECAUTIONS technology, ergonomic design and highly convenient operation General precautions ............4 at a low initial cost. The engine of the DBC340 brushcutter, with Personal protective equipment ........4 its optimum cylindrical design, computerized control times and Handling fuels / Refuelling ..........5...
- Page 3 Delivery inventory 1. Brushcutter 2. Shoulder strap 3. 4-tooth star blade 4. Cutter guard 5. Tool protection (not shown) 6. Servicing tool (not shown) 7. Instruction Manual (not shown) If one of these parts is missing when you unpack the brushcutter, contact your dealer! Explanation of symbols You will notice the following symbols on the brushcutter and in the instruction manual.
- Page 4 SAFETY PRECAUTIONS General precautions Proper use: These brushhcutters are provided with the appropri- ate and approved cutting tools for the respective applications as described on page 7. A brushcutter may be operated only by one person, and only out of doors! Improper use: The use of cutting tools or blades not approved for this brushcutter is forbidden and may cause damage or injury! Impermissible users:...
- Page 5 Handling fuels / Refuelling Stop the engine before refuelling (11). Keep away from open ß ame or sparks and do not smoke while refuelling or mixing fuel (5). Let the engine cool down before refuelling. Fuel may contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products.
- Page 6 Operate the brushcutter only with the shoulder strap attached, which is to be suitably adjusted before putting the brushcut- ter into operation. It is essential to adjust the shoulder strap according to the user’s size to prevent fatigue during use. Never hold the cutter with one hand during use.
- Page 7 Working behavior / Method of working Use the brushcutter only in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. Never cut above your shoulder height. Never stand on a ladder and run the brushcutter.
- Page 8 The performance of maintenance or repair work by the user is limited to those activities described in this instruction manual. All other work must be done by the MAKITA customer service (18). Use only original MAKITA spares and accessories. The use of non-MAKITA spares, accessories, or cutting tools increases the risk of accident.
- Page 9 1890 / 670 / 470 Weight (without plastic guard and tool) The maximum rated speed of the trimmer head is not exceeded when using a MAKITA trimmer head. Figures derived in equal part from idle and top-speed operation. At max. power.
- Page 10 PUTTING INTO OPERATION Mounting the tube handle CAUTION: When working on the brushcutter always be absolutely certain to switch off the engine, pull the spark plug cap and wear protective gloves! CAUTION: Do not start the brushcutter until fully as- The screws (A/1) and the handle clamp (A/2) are supplied sembled and inspected! with the accessories.
- Page 11 The position of the mounting plate (A/1) will depend on the type of cutting tool in use (trimmer head or metal blade). The position of the mounting plate determines whether the guard will be positioned higher or lower. When using a trimmer (line) head apply the mounting position as shown in Þ...
- Page 12 Installing the trimmer head Always switch off the engine and disconnect the spark plug cap before mounting the trimmer head! Unscrew the locknut (E/1) from the shaft by turning it clock- When using the trimmer head install the cutter guard with the wise.
- Page 13 The engine has been designed for Refuelling use of MAKITA high-performance two-stroke engine oil and a mixture ratio of only 50:1 to protect the environment. In addi- tion, a long service life and reliable operation with a minimum emission of exhaust gases are ensured.
- Page 14 Putting on the harness Place the harness over both shoulders so that the hip Adjust the height of the hip pad means by of the chest pad (C/3) is located on your right hand side. strap until the Þ xing hook is located about one hand’s width above the hip bone.
- Page 15 Move switch (A/1) to the position trigger lockout (A/2). Adjusting idling speed CAUTION: The carburetor must be adjusted only at an authorized MAKITA service centre. SERVICE Before adjusting the idling speed, the brushcutter should be run for 3 to 5 minutes until it is warm.
- Page 16 Failure to perform the prescribed mainte- nance work can lead to accidents! Do not do any maintenance or servicing work not described in this Instruction Manual. All such work may be done only by a MAKITA service station.
- Page 17 Starter cable replacement Loosen four screws (A/1) and remove the starter (A/2). Unscrew the screw (B/3) and remove it together with the disc (B/4). If the starter cable is not torn, the tension of the return spring must be released: CAUTION: Danger of injury! The return spring can spring Pull out the starter handle to a length of about 30 cm (12"), outwards.
- Page 18 Cleaning the air Þ lter CAUTION! To prevent eye injuries, do not blow out dirt particles! Very dirty Þ lters can be cleaned out using regular dishwashing liquid in lukewarm water. In case of strong pollution clean more often (several times a day) because only a clean Þ...
- Page 19 Replacing the suction head The felt Þ lter (G/5) of the suction head is used to Þ lter the fuel taken in by the carburetor. A periodical visual inspection of the felt Þ lter should be conduc- ted. For this purpose open the tank cap, and use a wire hook to pull out the suction head through the tank opening.
- Page 20 Please bear in mind that if parts other than original MAKITA spare parts are used, this will automatically invalidate the MAKITA product guarantee.
- Page 21 ) is 112 dB(A). The guaranteed sound power level (L ) is 113 dB(A). The technical documentation is on Þ le at MAKITA International Europe Ltd., Michigan Drive, Tongwell, Milton Keynes, Bucks, MK15 8JD, England. Anjo, 7.3. 2008 For MAKITA Corporation...
- Page 22 Notes...
- Page 23 Notes...
- Page 24 To Þ nd your local distributor, please visit www.makita-outdoor.com MAKITA Corporation SpeciÞ cations subject to change without notice 3-11-8 Sumiyoshi-Cho Anjo, Aichi Form: 995 704 204 (2.11 GB) 446-8502 Japan...