Yamaha EMX-120CD Owner's Manual page 29

COMPACT DISC PLAYER OPERATION
CD CHANGER RECEIVER EMX–120CD
PROGRAM
STANDBY/ON
ECHO MUSIC ECHO
KARAOKE MEMORY
PHONES
DISPLAY MEMORY AUTO/MAN'L
TIME ADJ TIMER
CD
1 2
1 2
6 7
6 7
A B
TIME
TIME PROG
MODE
2
DISC SKIP
CD TUNER
3
CENTER/REAR
TEST
/DELAY
ECHO
LEVEL
STANDBY/ON
SLEEP
VOLUME
Display information during programming
MUSIC PROGRAM KARAOKE
PRO LOGIC
TRACK
100 1K 10K
Playback order
Music calendar
MUSIC PROGRAM KARAOKE
PRO LOGIC
TRACK
100 1K 10K
Selected track number
1 6
A/B/C/D/E PRESET/TUNING/BAND
DISC
OPEN/CLOSE CHANGE
1 2 3
DISC DISC DISC
VOLUME
INPUT SELECTOR
CD TUNER
VCR•LD/TV•CD•TAPE/MD•TUNER
MIC TONE MIC MIC MIXING
REPEAT TIME INPUT TRIM
HOUR MIN
NORMAL SOFT MIN MAX
TIME
TUNER
3 4 5
4
3 4 5
8 PRESET
8 9 0
C D E
+
I0
REPEAT RANDOM OPEN/CLOSE 1
STOP PLAY/PAUSE
6
INPUT
FLAT
KARAOKE MUSIC PROGRAM
DISPLAY
1 2 3 4 5 6
7 8 9 10 11 12
13 14 15 OVER
PROG VOLUME
Selected disc
1 2 3 4 5 6
7 8 9 10 11 12
13 14 15 OVER
PROG VOLUME
Total playing time
Program play
You can program up to 20 tracks in any desired order.
1
Load discs and close the disc table.
2
When in the stop mode, press the PROG button to
prepare for programming.
* "PROG" and "P-01" will light up on the display, and all
track numbers on the selected disc will begin flashing.
3
If necessary, select a desired disc by pressing the DISC
SKIP button.
* Just after you change the disc, this unit reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
step, "WAIT" appears on the display and your
operation is canceled.
4
Use the track number input buttons to select the desired
track number.
* The selected track number and the total play time of
the programmed tracks will light up on the display, and
soon it will be replaced by the display of the next
playback order. Programmed track numbers on the
selected disc will stop flashing and light up on the
music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1) Press the "+10" button.
(2) Within 3 seconds, press the "2" button.
5
Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6
Press the play/pause
programmed tracks.
Notes
•
It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
•
During playback or pause, programming is not possible.
•
If the total time of the programmed tracks becomes 100
minutes or more, the highest position of the figure will not
be displayed.
•
The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
•
Skip search can be performed during playback, but only
within the range of the programmed tracks.
•
Manual search can be performed during playback to
search all tracks, including unprogrammed tracks.
•
If programs are made selecting tracks from more than one
disc, pressing the DISC CHANGE button is useless during
program play.
E-21
/ button to start playback of