Advertisement

Quick Links

Stinger .60 ARF
Lanier R/C
Stinger .60 ARF
Instructions
WARNING! THIS IS NOT A TOY!
THIS IS NOT A BEGINNERS AIRPLANE
This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily
harm and property damage. It is your responsibility, and yours alone - to build this kit
correctly, properly install all R/C. components and flying gear (engine, tank, radio, pushrods, etc.
and to test the model and fly it only with experienced, competent help, using common sense and
in accordance with all safety standards as set forth in the Academy of Model Aeronautics Safety
Code. It is suggested that you join the AMA and become properly insured before attempting to fly
this model. If you are just starting R/C modeling, consult your local hobby dealer or write to the
Academy of Model Aeronautics to find an experienced instructor in your area.
Write to : Academy of Model Aeronautics, 5151 Memorial Dr, Muncie, IN 47302
LIMITED WARRANTY
Lanier R/C is proud of the care and attention that goes into the manufacture of parts for
its model kits. The company warrants that for a period of 90 days, it will replace, at the
buyers request, any parts or material shown to the company's satisfaction to have been
defective in workmanship or material at the time of purchase.
1
Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566
Phone 770 532 6401 FAX. 770 532 2163
© Copyright 2002 Lanier R/C Inc.

Advertisement

Table of Contents
loading

Summary of Contents for Lanier R/C Stinger .60 ARF

  • Page 1 Write to : Academy of Model Aeronautics, 5151 Memorial Dr, Muncie, IN 47302 LIMITED WARRANTY Lanier R/C is proud of the care and attention that goes into the manufacture of parts for its model kits. The company warrants that for a period of 90 days, it will replace, at the buyers request, any parts or material shown to the company's satisfaction to have been defective in workmanship or material at the time of purchase.
  • Page 2 This one year limitation is imposed by agreement of the parties as permitted by the laws of the state of Georgia. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 3: Wing Assembly

    Measure from the tip of the stab to the front edge of the turtle deck on both sides and move the stab till both sides are the same. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 4: Landing Gear

    It should not take more than this to align the stab. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 5 Slide the wheel pant over holes and drill a # 55 (.052) pilot hole for the axel and put the wheel in place on the Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 6: Control Horns

    Use the same procedure and hinge both ailerons. To hinge the rudder, take a strip of wax paper 1-1/2" square and slip behind the tail wheel bracket wire. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 7: Engine Mounting

    Center the engine up on these lines and mark for the blind nuts. Drill Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 8: Tank Assembly

    When lined up properly tighten the screw. Install the tank in the fuselage with the cap fitting in the hole in the firewall. Tank assembly Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 9: Cowl Mounting

    Drill a 1/8" hole in the cowl on the top center so the screw will go into the firewall. Install the 3mm screw to hold Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 10 Bolt the wing in place and fit the hatch into the dowel holes in F2. Take a marking pen and mark along the sides of Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 11 Insert the 1/8" end into the holes, wrap Carefully put the canopy in place and with thread, and glue with thin CA. use masking tape to hold down till the Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 12 This pushrod with the nylon sleeve. You will completes the rudder pushrod. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 13 The control throws on low rate should be 3/8" up and down on the ailerons, 3/4" up and down on the elevators, and 3" left and right on the rudder. Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 14: Parts List

    Aluminum tubes (3) Right wheel pant Cowl Cowl mount blocks Wing cover Wing cover mount blocks Clear canopy Tail wheel bracket Tail wheel Wheel collar Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 15 Ten 2mm x17mm screws One throttle rod 1/16"x17-1/2" One plastic tube for throttle rod Two nylon swing in keepers Two aileron pushrods with clevis Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...
  • Page 16 Two 12 inch servo extension leads Fuel line. 2-1/2" spinner Adhesives Thin CA (cyanoacrylate) glue Medium CA (cyanoacrylate) glue 30 minute epoxy Z-42 threadlock Zap canopy glue Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 Phone 770 532 6401 FAX. 770 532 2163...

Table of Contents