List Of Parameters - GE VAT20 Series Instruction Manual

2. List of Parameters

Function
Accelerate /
Decelerate Time
Operation mode
Motor direction
V/F Pattern
Frequency
upper/lower limit
SPI frequency
JOG frequency
Operation control
Frequency Control
Carrier frequency
Torque compensation
Stop method
DC braking setting
Electronic thermal
Multifunction input
connection point
Multi-function output
Reverse lock-out
Momentary P. loss
Auto restart
Factory setting
SP2 Frequency
SP2 Frequency
Software version
Fault log
NOTE: *1: Indicate this parameter can be adjusted during running mode
*2: Please refer to Fn_25
*3: If the setting range is above 100 , the setting unit becomes 1.
*4: Only for drives with CPU version from 1.9 ( Check function F_29)
FN_ Function Description
01 Accelerate time
02 Decelerate time
03 0: Forward / Stop, Reverse / Stop
1:Run/Stop, Forward / Reverse
04 0: Forward 1: Reverse
05 V/F pattern setting
06 Frequency upper limit
07 Frequency lower limit
08 SP1 frequency
09 JOG frequency
10 0:keypad 1: external terminal
11 0:keypad
1:external terminal(0~10v/0~20mA )
2: external terminal ( 4~20mA )
12 Carrier Frequency setting
13 Torque compensation gain
14 0:decelerate stop, 1:free run stop
15 DC braking time
16 DC braking injection frequency
17 DC braking level
18 Protection on motor rated current
19 Multifunction input terminal 1 (SP1)
function
20 Multifunction input terminal 2 (RST)
function
21 Multifunction output terminal
22 0: REV run enabled
1: REV run disabled
23 0: enabled 1: disabled
24 Number of Auto-restart times
25 010: Constants initialization to 50Hz system
020: Constants initialization to 60Hz system
26 Frequency SP2
26 Frequency SP3
29 CPU program version
30 Fault Last 3 faults
Unit
0.1Sec
0.1Sec
1
1
1
0.1Hz
0.1Hz
0.1Hz
0.1Hz
1
1
1
0.1%
1
0.1S
0.1Hz
0.1%
1%
1: Jog
3: Emergency stop
4: External Base Block
5. Reset 6: Sp2
1: Operating
2: Frequency reached
1
1
1
0.1Hz
0.1Hz
21
Range Default Note
0.1 ~ 999 S 5.0
0.1 ~ 999 S 5.0
0 ~ 1 0
0 ~ 1 0
1 ~ 6 1/4
1.0 ~ 120Hz 50/60Hz
1.0 ~ 200Hz
0.0 ~ 120Hz 0.0Hz
0 ~ 200Hz
1.0 ~ 120Hz 10Hz
1.0 ~ 200Hz
1.0~ 10.0Hz 6Hz
1.0 ~ 200Hz
0 ~ 1 0
0 ~ 2 0
1 ~ 5 5
1 ~ 10
0.0 ~ 10.0% 0.0%
0 ~ 1 0
0.0 ~ 25.5S 0.5S
1 ~ 10Hz 1.5Hz
0.0 ~ 20.0% 8.0%
50 ~ 100% 100%
(0-200
2: Sp1 2
5
3: Fault 3
0 ~ 1 0
0 ~ 1 0
0 ~ 5 0
1.0 ~ 200Hz 20
1.0 ~ 200Hz 30
*1*3
*1*3
*1
*2
*2*3
*4
*3
*4
*3
*4
*4
*4
*1
*4
*4
*2
*4
*4