Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Control Unit
  5. 6015
  6. Installation and replacement notes

Cisco 6015 Installation And Replacement Notes

Dsl interface module fru
Hide thumbs Also See for 6015:

Advertisement

Quick Links

Download this manual
Cisco 6015 DSL Interface Module FRU
Installation and Replacement Notes
Product Number: 6015-48XDSL-I/F=
This document provides an overview of and installation and replacement procedures for the Cisco 6015
digital subscriber line (DSL) interface module. The DSL interface module is a field-replaceable
unit (FRU).
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Contents
This document includes the following sections:
•
Introduction, page 2
•
•
•
•
•
•
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2002. Cisco Systems, Inc. All rights reserved.

Advertisement

loading

Related Manuals for Cisco 6015

Summary of Contents for Cisco 6015

  • Page 1: Table Of Contents

    Cisco 6015 DSL Interface Module FRU Installation and Replacement Notes Product Number: 6015-48XDSL-I/F= This document provides an overview of and installation and replacement procedures for the Cisco 6015 digital subscriber line (DSL) interface module. The DSL interface module is a field-replaceable unit (FRU).

  • Page 2: Introduction

    The DSL interface module enables you to Connect the Cisco 6015 to a POTS splitter in a Cisco 6015 with a POTS splitter configuration • Connect the Cisco 6015 to the MDF or enclosure protection block in a Cisco 6015 without a POTS • splitter configuration Figure 1 shows the location of the DSL interface module in the Cisco 6015 chassis.
  • Page 3 If you are not currently using octal-port xTU-C line cards but plan to in the future, Cisco recommends that you use Champ cables that can accommodate higher density line cards. Refer to the Cisco 6015 Hardware Installation Guide for port mapping tables.

  • Page 4: Part And Tool Requirements

    EN55022 Class A compliance, ferrites are needed. • Cisco 6015 to MDF — If unshielded cable is used for FCC Class A or EN55022 Class A compliance, ferrites are needed. Equipment necessary for ESD protection—You need this equipment whenever you handle Cisco chassis, modules, and cards.

  • Page 5: General Safety Precautions And Maintenance Guidelines

    To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance Note and Safety Information for the Cisco 6015 System document that accompanied this product. Caution Before you start the installation procedures, read the entire document for important information and safety warnings.
  • Page 6 General Safety Precautions and Maintenance Guidelines This unit is intended for installation in restricted access areas. A restricted access area is where Warning access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.
  • Page 7 General Safety Precautions and Maintenance Guidelines A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Warning You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of Warning the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
  • Page 8 General Safety Precautions and Maintenance Guidelines Use caution when installing or modifying telephone lines. Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Warning Warning Secure all power cabling when installing this unit to avoid disturbing field-wiring connections. Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
  • Page 9 General Safety Precautions and Maintenance Guidelines This equipment is to be installed and maintained by service personnel only as defined by AS/NZS 3260 Warning Clause 1.2.14.3 Service Personnel. Network hazardous voltages are present in the T1 PRI cable. If you detach the cable, detach the end Warning away from the router first to avoid possible electric shock.
  • Page 10 The DSL interface module must be installed and removed by a trained technician only. Preventing Electrostatic Discharge Damage Proper ESD protection is required whenever you handle Cisco equipment. ESD damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures.

  • Page 11: Removing And Installing The Dsl Interface Module

    Always use an ESD ankle or wrist strap and ensure that the wrist strap makes good skin contact. • Connect the equipment end of the strap to the ESD grounding jack. There are two ESD grounding • jacks that are located on the following Cisco 6015 chassis modules: Fan module – DC PEM –...
  • Page 12 Cisco recommends that you label each data cable at both ends to identify its destination. Complete the following steps to remove the DSL interface module from the Cisco 6015 chassis: Connect a grounding strap to the ESD grounding jack that is located on the fan module.
  • Page 13 Step 5 Push on the faceplate of the module to fully seat the module. Use a flat-head or Phillips-head screwdriver to attach the four screws to the Cisco 6015 chassis. Step 6 Connect the DSL interface module to the POTS splitter (Cisco 6015 with a POTS splitter configuration) Step 7 or MDF (Cisco 6015 without a POTS splitter configuration).
  • Page 14 Figure 4 shows the cabling between the DSL interface module and a third-party POTS splitter. These connections are for xDSL data flow between the Cisco 6015 and the POTS splitter. Figure 4 Connecting the DSL Interface Module to the POTS Splitter...

  • Page 15: Standards And Certifications

    Set the circuit breaker on the DC PEM to the ON (1) position. Step 10 Standards and Certifications The DSL interface module has the same standards as the Cisco 6015 system, as shown in Table Table 3 Regulatory Compliance for Cisco 6015 Hardware...

  • Page 16: Related Documentation

    The following sections explain how to obtain documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at the following URL: http://www.cisco.com Translated documentation is available at the following URL: http://www.cisco.com/public/countries_languages.shtml...

  • Page 17: Obtaining Technical Assistance

    Priority level 1 (P1)—Your production network is down, and a critical impact to business operations • will occur if service is not restored quickly. No workaround is available. Which Cisco TAC resource you choose is based on the priority of the problem and the conditions of service contracts, when applicable. Obtaining Technical Assistance...
  • Page 18 Quotient, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.;...