Cisco Catalyst 6500 Series Installation Note
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. 6500 - Catalyst Series 10 Gigabit EN Interface Module...
  6. Installation note
Cisco Catalyst 6500 Series Installation Note

Cisco Catalyst 6500 Series Installation Note

Switch content switching module
Hide thumbs Also See for Catalyst 6500 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Troubleshooting Manual, Reference Manual
Catalyst 6500 Series Switch Content Switching
Module Installation Note
Product Number: WS-X6066-SLB-APC
This publication describes how to install the Content Switching Module (CSM) in the Catalyst 6500
series switches including the software and hardware requirements.
Contents
This publication contains these sections:
•
•
•
•
•
•
•
•
•
•
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
Using the CLI, page 17

Advertisement

Table of Contents
loading

Related Manuals for Cisco Catalyst 6500 Series

Summary of Contents for Cisco Catalyst 6500 Series

  • Page 1: Table Of Contents

    Obtaining Documentation, page 21 Obtaining Technical Assistance, page 22 • • Obtaining Additional Publications and Information, page 23 Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 2003 Cisco Systems, Inc. All rights reserved.

  • Page 2: Safety Overview

    éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 3 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 4 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...

  • Page 5: Front Panel Description

    During the normal initialization sequence, the status LED changes from off to red, orange, and green. Note For more information on the supervisor engine LEDs, refer to the Catalyst 6500 Series Switch Module Installation Guide. Table 1 describes the Status LED operation.

  • Page 6: Environmental And System Requirements

    40 C (32 to 104 Temperature, ambient nonoperating –40 to 70 C (–40 to 158 Humidity (RH), ambient (noncondensing) 10% to 90% operating Nonoperating relative humidity (noncondensing) 5% to 95% Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 7 Cable) Power Supply You can place the CSM in any slot in the Catalyst 6500 series chassis except for the slots that are occupied by the supervisor engine and the standby supervisor engine. The CSM operates on power that is supplied by the chassis.

  • Page 8: Installing The Csm

    Installing the CSM Software Requirements The CSM cannot be used in a Catalyst 6500 series switch with the Catalyst operating system prior to the Caution 7.5 release. Table 4 lists the software versions for the CSM: Table 4 CSM Software Requirements...
  • Page 9 When the system detects that a module has been installed or removed, the system automatically runs diagnostic and discovery routines, acknowledges the presence or absence of the module, and resumes system operation. These sections describe how to install and verify the operation of the CSM in the Catalyst 6500 series switches: •...
  • Page 10 Removing the Module This section describes how to remove an existing module from a Catalyst 6500 series switch chassis slot. During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly Caution touch the backplane with your hand or any metal tool, or you could shock yourself.
  • Page 11 Installing a Module This section describes how to install a supervisor engine or module in the Catalyst 6500 series switches. To prevent ESD damage, handle modules by the carrier edges only.
  • Page 12 45 degrees with respect to the module faceplate. (See Figure Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 13 While pressing down, simultaneously close the left and right ejector levers to fully seat the supervisor engine or module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 14 Position the supervisor engine or switching module in the slot. (See Figure 5.) Make sure that you align the sides of the switching-module carrier with the slot guides on the top and bottom of the slot. Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 15 Using the thumb and forefinger of each hand, grasp the two ejector levers and exert a slight pressure to the left, deflecting the module approximately 0.040 inches (1 mm) to create a small gap between the module’s EMI gasket and the module adjacent to it. (See Figure Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 16 While pressing on the ejector levers, simultaneously close them to fully seat the supervisor engine or module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...

  • Page 17: Verifying The Installation

    This completes the CSM installation procedure. Verifying the Installation When you install the CSM into the Catalyst 6500 series switch, the module goes through a boot sequence that requires no intervention. At the successful conclusion of the boot sequence, the green Status LED will light and remain on.

  • Page 18: Related Documentation

    Configuration Guide. To understand the Catalyst operating system command-line interface and Catalyst operating system command modes, refer to Chapter 2, “Command-Line Interfaces,” in the Catalyst 6500 Series Switch Configuration Guide. Unless your switch is located in a fully trusted environment, we recommend that you configure the module through a Telnet connection using Secure Shell (SSH) encryption.
  • Page 19 à l’intérieur du châssis, ils évitent toute diffusion d’interférences électromagnétiques qui pourraient perturber le fonctionnement des autres équipements, et ils canalisent le flux d’air de refroidissement dans le châssis. Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...
  • Page 20 (EMI) som kan störa annan utrustning; och de styr riktningen på kylluftsflödet genom chassit. Använd inte systemet om inte alla kort, framplattor, fram- och bakskydd är på plats. Catalyst 6500 Series Switch Content Switching Module Installation Note 78-15751-01...

  • Page 21: Obtaining Documentation

    Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/cisco/web/psa/default.html?mode=prod You can access the Cisco website at this URL: http://www.cisco.com...

  • Page 22: Obtaining Technical Assistance

    24 hours a day, 365 days a year. Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL: http://tools.cisco.com/RPF/register/register.do...

  • Page 23: Obtaining Additional Publications And Information

    TAC Case Priority Definitions To ensure that all cases are reported in a standard format, Cisco has established case priority definitions. Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
  • Page 24 CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...

Table of Contents