Features; Ac And Dc Charging/Recharging; Viewing Battery Charge Status; 120 Volt Ac Charging - Black & Decker ELECTROMATE VEC027BD User Manual

VEC027BD_ManualEN_122805 12/28/05
Protective Features
• Automatic Overload — Built-in protection against overload — in the event the
AC outlet draws more than 300 watts, power to the unit's outlet will automatically
shut off.
• Ground Fault Circuit Interrupter (GFCI) — The GFCI protects the unit and the
user by sensing imbalances in a circuit caused by current leakage to the ground
and shuts down the unit's AC outlet to prevent electrical shock.
• Overheating — Unit automatically shuts down if it exceeds a safe temperature.
• Safety Power Switch and Reverse Polarity Alarm — In event the
cables/clamps are reversed during jump-starting, an indicator lights and an alarm
sounds BEFORE the Power Switch is turned ON.
• Low Battery — If the battery power level is too low, the AC Power Supply shuts
down automatically.
Front View
UNIT FRONT PANEL UNIT FRONT PANEL RUBBER HANDLE
AIR VENTS
DC POWER SUPPLY
PANEL
AC POWER SUPPLY
PANEL
Front Panel
BATTERY CHARGE
LEVEL INDICATORS
JUMP-START SAFETY
ON/OFF SWITCH
REVERSE POLARITY
INDICATOR
AREA LIGHT
ON/OFF SWITCH
Air Inflator Nozzles
2:37 PM Page 2
Back View
AC CHARGER
JUMPER CABLE
CONNECTOR
INFLATOR
12 VOLT DC ADAPTER STORAGE
COMPARTMENT
BATTERY CHARGE LEVEL
PUSHBUTTON
ALTERNATOR CHECK
INDICATOR
INFLATOR PRESSURE
GAUGE
INFLATOR
ON/OFF SWITCH
AREA LIGHT
2

AC AND DC CHARGING/RECHARGING

Use a common household AC extension cord for charging (cord not supplied).
For maximum battery life, we recommend the unit be kept fully charged at all times.
If the battery is allowed to remain in a discharged state, battery life will be shortened.
• MAKE SURE ALL SWITCHES ARE TURNED OFF DURING RECHARGING.
• Charge the unit for a full 24 hours using AC method before first use.
• Recharge the unit fully after each use.
• Recharge the unit every two months when it has not been used regularly.
Notes:
Recharging the battery after each use prolongs battery life; frequent
discharges between recharges reduces battery life.
The Electromate Plus also comes with a DC/DC charging adapter for recharging
the unit from a 12 volt DC accessory outlet in a vehicle.
If unit is fully discharged, it is recommended that the vehicle being used for
recharging be left running while the unit is charged via the 12 volt DC method.

Viewing Battery Charge Status

Press the Battery Charge Level pushbutton to display battery status. The Battery
Charge Level Indicator LEDS will light.
LEDS (from left to right):
• Red LED indicates a low battery charge
• Two Red LEDs indicate a medium level or partially charged battery
• Two Red and one Green LED indicates a full or high level battery charge.

120 Volt AC Charging

1. Lift the AC adapter cover located on the back of the Electromate Plus and
connect an extension cord to the unit. Plug the other end of the cord into a
standard 120 volt AC wall outlet.
2. Charge until two Red and one Green LEDs light.
3. Once fully charged, disconnect the extension cord.
Note:
The unit cannot be overcharged using the AC method.

12 Volt DC Charging

The DC recharging method will NOT recharge the unit as effectively as recharging
from 120 volt AC. The 12 volt DC recharging procedure is recommended only when
it is necessary, since frequent use of the 12 volt DC recharging procedure may
shorten the battery system's life.
1. Insert the gold-tipped DC/DC charging adapter plug into the vehicle's 12 volt DC
accessory outlet.
2. Insert the silver-tipped end plug into the 12 volt DC accessory outlet on the front
panel of the unit.
3. To check the charge status of the battery during DC charging, disconnect the DC
adapter from the accessory outlet and push the Battery Charge Level pushbutton.
Observe the battery charge indicator.
4. When charging is complete, remove the power cord and return it to the storage
compartment.
3