1. SPECIFICATIONS Power consumption In operation Standby Mode SW OFF Memory protection Backup battery Vanadium Lithium secondary battery VL3032/1F2 Back up period 90 days (25°C) Battery life 5 years (25°C) Recharge time 48 hours Memory capacity 1Mbits uPD431000ACZ-70LL Within ±30 sec. per month(25˚C) Clock and calender Accuracy Auto calender...
2. INITIALIZE (MAC) OPERATION 1. Set the mode switch to "OFF" position. 2. Press the "INIT SW". 3. Turn the mode switch to ""REG" (Except "OFF" or "Z") position. 4. Release the "INIT SW" . 5. Input the MAC CODE. (10 digits) 6.
5.DISASSEMBLY (FE-700) 5-1.MAIN PARTS 1.Open the printer cover. Remove the 2 screws of the upper case. Remove the 2 screws. 2.Slide the upper case to the front side. 3.Open upper case from the left side. 4.The battery is located at the printer fixing stand. Battery VL3032/1F2 —...
Page 8
5. Release the hook them Remove the write side. Hook 6. Release 3screws to remove printer plastic stand. Remove the 4 screws. 7. Release 2screws to remove printer unit. Remove the 2 screws. 8. Release 1 screw to remove display case. Remove 1 screw.
Page 9
9. Lift up upper case. 10. To remove the main PCB, release 7 screws and 2 screws for the COM port. Remove the 7 screws. Remove the 2 screws for the COM port. — 7 —...
6.CIRCUIT EXPLANATION 6-1. Power supply circuit Q1 : Power transistor Q2 : Voltage detection transistor Voltage level at above check point (unit : V ) Measurement position Voltage (V) 12.5V 5.3V 6.2V 2 .47V — 8 —...
6-2. CPU (IC11: uPD78052GC-A46-8BT) Status of Status of Pin No. Signal Description In/Out Power On Power OFF Fiscal ROM bank 3 High High Fiscal ROM bank 4 / RAM bank 3 High High Fiscal ROM bank 5 / RAM bank 4 High High AVSS...
Page 12
Status of Status of Pin No. Signal Description In/Out Power On Power OFF HD.E Head drive signal of printer (HD.E) HD.F Head drive signal of printer (HD.F) HD.G Head drive signal of printer (HD.G) HD.H Head drive signal of printer (HD.H) RESET Reset signal (RESET) High...
6-3. Display controller (IC2: uPD16312GB-3B4) Status of Status of Pin No. Signal Description In/Out Power On Power OFF Not used (GND) Not used (GND) Not used (GND) Not used (GND) DOUT Data out signal to CPU High High Data in signal from CPU Pulse High Clock signal (CLK)
6-4. Initilize IC (Reset circuit) VDD : Voltage of memory protection battery To Pin No.60 of CPU When the voltage level at Pin No.60 of CPU is not stabilized, CPU does not work properly in rare case. Therefore, this machine uses the initialize IC for stabilizing the voltage. Even the voltage lebel of VDD(Pin No.2) is changed, Pin No.1 of initilize IC outputs stabilized 5 volts.
6-7. RAM / ROM / Fiscal ROM bank selection circuit IOGATE HC32A GATE IC22 F. ROM1 HC32A IC22 F.ROM2 HC32A IC22 R123 HC32A IC22 100P EEPCE This circuit is used for address decoder for mamory. RAM 1M RAM256K Memory Map 00011 00101 00001...
6-8. Fiscal ROM address and data selection This circuit is used for interface of Fiscal ROM. To improve the signal level of interface, this machine is used buffer IC (TC74HC367A) at all signal lines. IC8 is used for the gate of data bus between te Fiscal ROM and CPU. —...
6-9. Head drive circuit for printer Motor drive circuit Normally, the transistor of motor drive circuit is followng condition. TR1,TR2,TR5 : TR3, TR4 : MD(-) signal : VP level When the CPU want to rotate the motor, CPU change the MD signal to "High" from "Low". Then, TR1,TR2 and TR5 are become ON and MD(-) signal is become GND level, and then motor is rotated.
6-10. VPP sensor circuit This circuit is using for making the voltage when the CPU write the data to Fiscal ROM. When the CPU wants to write the data to Fiscal ROM, CPU makes the "VPP.ON" signal to "Low level". DCS2 (PS10017): Booster circuit ( from 5V to 13V ) IC3 (M5237L) : IC for making 5V from 13V Each voltage level (Unit : V)
Protection circuit To prevent the Fiscal ROM breakage, the protection circuit watches the voltage lebel of VCC,VDD,FVCC and VPP. When the each voltage level is more than following condition, this circuit cuts the voltage. VCC,VDD and FVCC : In case these voltages are become over voltage, this circuit outputs "SCR"...
7-4. Switch status test Press "C" button, the switch status is appeared on the display. [DISPLAY] No display No display No display No display Pop up display 1: Not connected 0: Connected INIT switch 1 : ON 0 : OFF Vpp level of Fiscal ROM 1 : High level (12V) 0 : Low level (5V)
7-5. Individual function test 1) Series test This test will perform the following tests in series. 1. All display test (display all segment and TL,CG transactions) 2. Main ROM sum test 3. RAM read test (one time) 4. Drawer open test 5.
Page 23
2) Print a ging test This test will print 45 lines following print pattern in a one minutes. Opeartion : Y 2 #2 Y : 0 = Normal test ( It is not necessary to input "0". ) 1 = Continuous print test X : 0 = Print 45 lines in a one minutes.
Page 24
4) RS232C port test This test will execute the RS232C loop back test continuously using loop back connector. In case an error happens, the machine issues an error receipt then stop this test. Test description : 1 : Level check at DSR signal ( Low/High) 2 : Send the data (0A5h) from TxD and receive it at RxD terminal.
7-6. Fiscal ROM test 1) Fiscal ROM test This test will check the fiscal ROM area for the test operation. Opeartion : 1 7 #2 X : 0= Fiscal ROM information print 1= Fiscal ROM data dump print 2= Fiscal ROM write test in the test area 3= VPP (Fiscal ROM write voltage) test [PRINT] Normal end...
8. ERROR CODE 8-1.Operation error code When an error condition is generated, one of the following error codes (E01 – E94) is displayed to indicate the cause of the error and the corrective action. DISPLAY ERROR REMARKS/CORRECTIVE ACTION Initialize or Flag clear operation error Retry the operation correctly.
8-2. Fiscal ROM error code Error code will be printed when the machine has the Fiscal ROM memory trouble. Error Meaning Action Code Read after write error Initialize or Flag clear operation is necessary. Verify after write error Initialize or Flag clear operation is necessary. Read error Initialize or Flag clear operation is necessary.
8-3. System lock code The following error code appears on display and receipt when the machine is lock up. Execute the Flag MAC or MAC operation to clear these errors. Error code : Display : X - - - - - - - - - Receipt : X ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! X : Lock code...
Page 31
9. TC74HC245AP (IC8) Inputs Output Y Bus B Data to Bus A Bus A Data to Bus B (Topview) 10. TC74HC367AP (IC7,9,10,23-25) Output Control G Output Control G 11. TC74HC373AP (IC13) Output Control Output Enable Control Enable — 29 —...
Page 32
12. TL431CLPB (IC1) Cathode(K) Vref Vref = 2.5V Anode(A) 13. (IC14) A0-A16 Address Inputs Q0-Q7 Data Outputs Chip Enable Output Enable Program M27C1001 Program Supply Supply Voltage Ground Not Connected Internaly A100711 — 30 —...
Page 33
14. (IC15) A0-A16 Address Inputs I/O1~I/O8 Data Outputs CE1, /CE2 Chip Enable Inputs 1,2 Right Enable Inputs Output Enable Inputs Supply Voltage Ground Not Connected Internaly /CE1 I/O8 I/O1 I/O7 I/O2 I/O6 I/O3 I/O5 I/O4 — 31 —...
2. As for spare parts order and supply, refer to the “GUIDEBOOK for Spare Parts Supply”, published separately. 3. The numbers in item column corespond to the same numbers in drawing. 4. CASIO does not supply the spare parts without parts code. 5. Remarks Q'ty :...
Code No. Name Specification Price Code R Item RESISTOR/CARBON FILM RD14J331T26 R25, 36 RESISTOR/CARBON FILM RD14G242T26 R26,119 RESISTOR/CARBON FILM RD14J221T26 R27, 40, 142 RESISTOR/CARBON FILM RD14G103T26 R29, 30, 62-69, 111, RESISTOR/CARBON FILM RD14J102T26 112, 116, 118, 132 RESISTOR/CARBON FILM RD14G102T26 R31, 39 RESISTOR/CARBON FILM RD14J301T26...