Installation - Honeywell GENT VIG-RPT-72 Installation Manual

Data and installation

Installation

The Repeat Panel Set consists of:
Parts
j Backbox assembly
k Outer door assembly
l Inner door assembly
(with membrane labels for BS panel)
m 20 Way ribbon cable
n 40 Way ribbon cable
† Spares pack [Battery lead, Link wire (not used),
1 x 2A Fuse 20mm x 5mm QB,
2 x 3.15A Fuse 20mm x 5mm AB ceramic]
‡ Battery 12V 7Ahr
Fuses on the Master Repeat Card
Fuse Rating
FS4 3.15A AS 20mm x 5mm
FS2 3.15A AS 20mm x 5mm
FS3 2A QB 20mm x 5mm
Back box mounting
3-off
Earth points
115mm
RESET
P2
SW3
P1
P7 FS3
USB 2A(QB)
Backbox
Floor level
Find the Repeat panel Back box  package and
a
remove the temporary cover.
Secure the back box to the wall with suitable
b
fixings. If the backbox is to be semi-flushed then
use the optional semi-flush surround.
Terminate the cable at the entry point leaving
c
400mm tail wire length.
&
If mains supply cable ends are not
required to be connected then ensure the ends are
insulated for safety.
2
www.acornfiresecurity.com
Qty
1
1
1
1
1
1
1
Cable entry points
4-off - Back and 4-off - Top
310mm
115mm
c L
P9
L N N
0C LC 01 L1 02 L2
P17
P16
FS4
WRITE PROTECT
DANGER
P4 L N
P8
DANGER
DO NOT
REMOVE
WARNING
Removal of
cover exposes FS2
BUZZER
live parts.
DISABLE DANGER
WD1
P14
P5
PB2
-
+ 0V 24V
RS485
Fixing centres
4-off
www.acornfiresecurity.com
Vigilon Repeat panel (EN/BS)
Refit the temporary cover to protect the panel
d
until all building work is complete.
Aperture
Repeat panel
semi-flush surround
Flush
Repeat Panel
Surround
5mm diameter
fixing holes Aperture Width: 320mm
Doors, Cables and Power up
The doors and cables can be installed after the
building work has finished.
Remove the protective cover from the backbox.
a
ƒ
b
Fit the inner door to the panel enclosure
remembering to connect the earth lead from the
backbox to the inner door. Fit the outer moulded
‚
door to the backbox.
Wiring the panel:
c
&
Ensure the mains supply is completely
powered down before wiring the mains cable ends.
•
connect the mains cable to terminal block P9
on the Master Repeat Card.
• †
fit battery lead supplied in the spares to
connector P5 on Master Repeat Card.
•
connect the loop cables to terminal block P16
on the Master Repeat Card.
•
connect the 40 way ribbon cable
Master Repeat Card connector P2 and the
other end to Display Key Card on the top right
edge connector - P1.
•
connect the 20 way ribbon cable
Master Repeat Card connector P1 and the
other end to Display Key Card on the top right
edge connector - P6.
Power-up the panel by switching ON the mains
d
supply and then connect the battery leads to the
battery and note:
•
all the LEDs on the panel are lit for a short
duration and a power up message displayed.
•
the local buzzer sounds
•
the display reads: Main panel is off Line
•
the Fault and System Fault LEDs are lit.
4188-839_issue 8_07/14_pt1_EN/BS new Repeat_inst
Cross section of the wall to which
the panel is to be semi-flush mounted
Aperture depth should
not be less than: 59mm
Aperture Height:
380mm
…
to the
„
to the