AEG ST 500 Instructions For Use Manual page 2

Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Use
Mains
connection
ENGLISH
You demand the best and buy quality – quality provided by Atlas Copco.
We have built for you a reliable and lasting tool. Working effectively and without
endangering your health is only possible if these instructions for use are being read
carefully before first using this tool. We want to satisfy our customers and would
like you to buy again
Cutting depth max. in:
Soft– wood . . . . . . . . . . . . . . . . . . .
Hard–wood . . . . . . . . . . . . . . . . . .
Steel . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminium . . . . . . . . . . . . . . . . . . .
Nominal power . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . .
Stroke rate under no-load
Lengths of stroke
Bevel cuts up to
J Please pay attention to the safety instructions in the attached leaflet!
J Dust that arises when working on material containing asbestos or stonework
containing crystalline silicic acid is harmful to the health. Please follow accident
prevention regulations.
J Appliances used at many different locations including open air must be connected
via a current surge preventing switch.
J Always use the protective shields on the machine.
J Always disconnect the plug from the socket before carrying out any work on the
machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Only plug-in when machine is switched off.
J Dust that arises when working on wood or using the tool on industrial material can be
dangerous to health. In this case connect the tool to a suitable suction device.
J Do not use cracked or distorted saw blades.
Typically the A-weighted sound pressure level of the tool is 82 dB (A).The noise
level when working can exceed 85 dB (A). Wear ear protectors! Measured values
determined according to EN 50 144.
Typically the weighted acceleration is 3 m/s
Measured values determined according to EN 50 144.
This jig saw can cut wood, plastic and metal; it can cut straight lines, bevels, curves,
and internal cut-outs.
Do not use this product in another way as stated for normal use.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
1
AEG Electric Power Tools from Atlas Copco.
ST 500
65 mm
55 mm
5 mm
10 mm
500 W
1,9 kg
. . . . . . 3000 min
. . . . . . . . . . . . . . . 19 mm
o
. . . . . . . . . . . . . . . 45
STE 500
. . . . . . . 70 mm
. . . . . . . 60 mm
. . . . . . . . 5 mm
. . . . . . . 10 mm
. . . . . . . . 500 W . . . . . . . .
. . . . . . . . . 1,9 kg
-1 -1
. 450-3000 min
. . . . . . . 19 mm
o
. . . . . . . . . . 45 . . . . . . . . . . .
2
.
ST 500, STE 500, STEP 500
STEP 500
. . . . . . . . 70 mm
. . . . . . . . 60 mm
. . . . . . . . . 5 mm
. . . . . . . . 10 mm
500 W
. . . . . . . . 1,9 kg
-1
. 450-3000 min
. . . . . . . . 19 mm
o
45