Related Manuals for GE ERESCO MF4 Series
Summary of Contents for GE ERESCO MF4 Series
- Page 1 X-ray Sensing & Inspection Technologies Industry X-ray Unit ERESCO MF4 Type Series Digital control unit ERESCO MF4 control Operating manual...
- Page 2 File: 37020GB-F Betriebsanleitung_ErescoMF4.indd Printed in Germany 2016 GE Sensing & Inspection Technologies GmbH reserves the right to technical modifications without prior notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of GE Sensing &...
-
Page 3: Table Of Contents
Generating Programs ..........................35 2.10 Calling and Exiting Programs ........................39 2.11 Switching the backlight on and off ......................40 2.12 Setting the Display Contrast ........................40 Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 4 Checking the Automatic Shut-Off of the Flow Rate Monitor (optional) ..........65 8.4 Checking fail-safe operation of the optional warning flash light ............65 Replacing the high voltage lamp at the digital control unit ERESCO MF4 control ........66 Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 5 Appendix 2: Connection Diagram ..........................81 Appendix 3: Image Quality of Test Specimen EN 462 ....................82 Appendix 4: Operation with Centring Laser ....................... 83 Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016...
-
Page 6: Safety Information
Indication of unauthorised entry or intervention Caution: Danger of crushing Caution: Laser radiation hazard, Indication of special information, following instructions Symbol for "hazardous waste segregation" Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 7 Exposure to high concentrations of mercury vapor can cause a variety of severe symptoms. Risks include chronic inflammation of mouth and gums, personality change, nervousness, fever, and rashes. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016...
-
Page 8: Radiation Protection Information
X-ray units, make use of the full length of the connecting cable between the radiating unit and the control. All automated GE Sensing & Inspection Technologies controls render operator-guided monitoring of the operating values unnecessary during radiation time. Therefore, immediately after HV switch-on, the operator can further increase the distance from the X-ray tubehousing or the radiating unit. - Page 9 The effect of this measure is increased since after switch-on (approx. 6 sec./100kV) the high voltage is slowly increased from zero to the preselected value in the case of all GE Sensing & Inspection Technologies control units.
-
Page 10: Safety Notes
• Work on the unit's electrical equipment may only be carried out by electricians trained by GE Sensing & Inspection Technologies. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 11: Personal Protective Clothing
Any other use of the unit is strictly prohibited. Improper use or tampering with the unit may result in personal injuries or damage to the unit. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 12: Operating Manual
NOTE: The digital control unit ERESCO MF4 control can operate with restrictions (see section 3.), also as stand-alone equipment (without X-ray unit). Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 13 GE Sensing & Inspection Technologies GmbH. When using an emergency power generator, please ensure that a sinusoidal voltage is applied as described in section 2.2.1. If you have any further questions, please contact GE Sensing & Inspection Technologies GmbH. Key-operated switch...
- Page 14 Valid for all details (minimum values) Fig. 4 - Radiating unit for operation in closed rooms or radiation protection cabinets Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 15: Operation With Optional Warning Flash Lamp
Both door contacts must be closed before the unit is ready for operation again. Short circuit plug with eyebolt Eyebolt Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 16: Taking Into Operation
Input via the keypad is not possible. However, a status request via the serial interfaces is possible. The following mask appears on the display. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 17: Display Modes
Rectifier temperature in ERESCO MF4 control Cascade temperature radiating unit Gas pressure radiating unit Final stage temperature Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 18 Key F2 show or hide measured values Key F3 not used Key F4 Enter Film-Focal-Distance Key F5 not used Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 19: Ready For Operation And Warm-Up
Press the F3 / Warm-up voltage key, enter the desired warm-up voltage in the Warm-up voltage field and then press the OK key. Subsequently press the key or the OK key: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 20 Press the key to confirm the message. The operating mask (e.g. manual mode) which was selected prior to warm-up subsequently appears: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 21 20 kV (but not below ) is reduced and the following message appears in the comment line on the nominal/2 display: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 22 The warm-up program can be called manually as follows: Press the F1 key until the symbol appears. Press the F4 key. The warm-up mask appears (see page 19). Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 23: Extended Warm-Up Mode
The X-ray unit will be warmed-up with an special warm-up program always to the maximum tube voltage. It is not possible to enter a warm-up voltage, less than the maximum tube voltage. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... - Page 24 The unit can only be restarted after a renewed mains ON. In this case, a service technician should be consulted. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 25: Setting The Operating Parameters
The maximum exposure time is 30 min.) Press the F1 key [mm'ss''] or (s) to toggle between the sec. display and the min/sec. display for the exposure time. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 26: Kv Setting
Press the F3 / mA key. The set-point value of the tube current is displayed inversely. Enter the desired mA value and press the OK key to confirm the set mA value. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. -
Page 27: Power Mode
The unit then switches off with message 124: reduce power . Remedy: Reduce the power by approx. 20% and increase the exposure time correspondingly. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 28: Exposure Calculator
Press the F2 key to change the function key arrangement, and the Material parameter in the Exp.Parameter field is displayed inversely: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 29 Exp. Parameter setup. When all the settings and calculations have been carried out, press the F5 key to exit the exposure calculator: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 30 To carry out exposures with the calculated values in manual mode, the function key arrangement must be changed to standard mode by pressing the F1 key several times: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 31: Ffd-Correction
The integrated computer calculates the exposure time for the entered Film-Focal-Distance and the calculated value is preset. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... - Page 32 The unit then switches off with message 124: reduce power . Remedy: Reduce the power by approx. 20% and increase the exposure time correspondingly. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 33: Starting Exposure
If necessary, the message 106: Warm-up necessary is displayed, and the warm-up program is called after pressing the F4 key. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 34: Exposure Stop
2.3.1. If the high voltage is set higher than the warm-up voltage, the message 106: Warm-up necessary! appears on the display (also see section 2.7). Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 35: Generating Programs
If a program already exists under the desired program number, the following message appears: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 36 (The entered program names will not assumed when saving the program into the X-ray unit (see setup menu item 14 Memory location)) To achieve this, press the F1 key. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 37 Press the F5 key to exit the mask and to reject the entries. Press the F4 key to accept the name. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 38 Select another program number. Press the F4 key to overwrite the existing program, the program mode appears on the display. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 39: Calling And Exiting Programs
Press the F3 key to call a new program at any time, as described above. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 40: Switching The Backlight On And Off
Press the OK key to accept the set value. NOTE: The backlight and the contrast setting can only be activated when the display mode shows the parameters. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 41: Setup Menu
The operating hours of the digital control and the radiating unit with integrated insert tube are displayed. Furthermore the serial number of the connected radiating unit and the integrated insert tube are displayed. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 42: Tube Data
After carrying out all the settings and confirming them via the OK key, press the F5 to return to the setup menu. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 43: Prewarning
With a connected warning flash lamp, an prewarning time of at least 2 seconds m u s t be set, otherwise the high voltage cannot be switched on. The prewarning time is factory set to 2 seconds. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 44: Real Time Clock
Press the F4 key to display the mask with the changed values. Press the F5 key to exit the menu item. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 45: Software Id
OK key to activate the selected language. The setup menu will be displayed again. Press the F5 key to exit the menu without changes. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 46: Input Ports
Row 5: status indication of the ports (OK / ERROR) Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 47: Operat. History
Press the F4 e key to call a further mask which, in addition to the permanently displayed values (see above), also shows the timer nominal and actual value ( ) and the program number Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 48: Warm-Up History
Furthermore, it is also displayed whether the buffer battery is empty (X) or not. NOTE: If a buffer battery is empty, the date and time display is only correct if it has been set correctly after switching on the unit. Press the F5 key to exit the menu. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 49: Dimension Unit
Press the F4 key to display the result of the change. Press the F5 key to exit the menu. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 50: Beeper
Press the F4 key or the OK key to accept the setting. Press the F5 key to exit the menu. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 51: Exposure Calculator
Press the F4 key to accept the entry. Press the F3 key to call the default values stored in the unit: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 52 Press the F5 key to exit each menu without value changes. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 53: Memory Location
X-ray unit (e.g. for field service). Note: If the Administrator Software program is present, the data can be administrated if necessary with this program. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 54: Interlock Mode
5 and 6: Door contact 2 between 9 and 10: EMERGENCY STOP between pin 11 and 12: EMERGENCY STOP Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 55 Door 1 opens: Door 1 opens: Both door contact Only 1 door contact circuits circuit is connected are connected Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 56: Protective Devices
After eliminating the faults, press the CL key to confirm the messages. (If one of the warning lights fails during operation, the high voltage is immediately switched off and the messages described above appear) Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 57: Fuses And Pin Assignment At Eresco Mf4 Control
5 and 6: Door contact 2 between pin 9 and 10: EMERGENCY STOP between pin 11 and 12: EMERGENCY STOP Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 58 If only one connection (pins 4/5 or pins 4/6) is used, the other contact must be jumpered. Pin assignment X6 for interface V24 Pin 1: Pin 2: Pin 3: Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 59: List Of Messages
Operating Manual ERESCO MF4 Type Series List of Messages Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 60 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 61 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 62 · is operated in extremely high or extremely low ambient temperatures. To ensure normal operation, GE Sensing & Inspection Technologies recommends conditioning the radiating unit in power mode. To achieve this, the following operating parameters are required:...
-
Page 63: Maintenance
The manual warm-up program is only available for trained service personnel. The Extended warm-up contains three programs: up to 160 kV, up to 200 kV and up to 300 kV Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 64: Water Cooling Pump Wl 1001 (Optional)
• If the set minimum flow rate is not achieved, a flow rate monitor switches the X-ray unit off. It is advisable to have maintenance carried out by service experts from GE Sensing & Inspection Technologies to avoid possible high resulting costs. -
Page 65: Checking The Automatic Shut-Off Of The Flow Rate Monitor (Optional)
The high voltage is switched off and the following message 87: Flash lamp faulty appears on the display. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 66: Replacing The High Voltage Lamp At The Digital Control Unit Eresco Mf4 Control
3. Lamp covers are installed in reverse order. When inserting the yellow cap, make sure that the high voltage arrow is pointing downwards. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 67: Dismantling And Disposal
Use PPE in accordance with the safety data sheet. The mineral insulating oil should be entrusted for proper disposal to a certified waste dis- posal company. Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 68: Technical Data
***) Protection class IP 65 can only be guaranteed when plugs are connected (seal unused plugs with a cap) or when using the rubber cap! Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016... -
Page 69: Eresco 32 Mf4-C
Min. cooling water flow rate 2.5 l/min Max. cooling water pressure 10 bar Cooling water quality Drinking water Hose connection Ø 11 mm Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 70: Eresco 52 Mf4-Cl
Min. cooling water flow rate 2.5 l/min Max. cooling water pressure 10 bar Cooling water quality Drinking water Hose connection Ø 11 mm Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 71: Eresco 160 Mf4-R And Eresco 160 Mf4-Rw
Min. cooling water flow rate 2.5 l/min Max. cooling water pressure 10 bar Cooling water quality Drinking water Hose connection Ø 11 mm (7/16") Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 72: Eresco 280 Mf4-R And Eresco 280 Mf4-Rw
Min. cooling water flow rate 2.5 l/min Max. cooling water pressure 10 bar Cooling water quality Drinking water Hose connection Ø 11 mm (7/16") Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 73: Eresco 300 Mf4-R
290 mm (11.42“), 225 mm (8.85“) without carrier rings Current and voltage stability ± 1% Power consumption, max. 2.0 kVA Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 74: Index
Pin configuration 57 Flash lamp 33 Ports 46 Focus size 42 X-ray tube 56 Power mode 27 Gas eruptions 56 Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 75: Appendix 1: Exposure Diagrams
Operating Manual ERESCO MF4 Type Series Appendix 1: Exposure Diagrams Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 76 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 77 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 78 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 79 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 80 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 81 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
-
Page 82: Appendix 2: Connection Diagram
Operating Manual ERESCO MF4 Type Series Appendix 2: Connection Diagram Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 83: Appendix 3: Image Quality Of Test Specimen En 462
H 14 GE Sensing & Inspection Technologies GmbH Bogenstr. 41 • 22926 Ahrensburg • Germany • Tel.: +49/4102/807-0 • Fax: +49/4102/807-189 • gesensingnspection.com Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... -
Page 84: Appendix 4: Operation With Centring Laser
2 x 1.5 V AAA micro alkaline or equivalent Laser type: Semi-conductor diode laser Wavelength: 635 - 670 nm red Dimensions (WxDxH) 175 x 17 x 50 mm Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F... - Page 85 Operating Manual ERESCO MF4 Type Series CAUTION: To guarantee correct operation, only use original GE Sensing & Inspection Technologies accessories with ERESCO MF4 Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 86 Operating Manual ERESCO MF4 Type Series Copyright by GE Sensing & Inspection Technologies GmbH Bogenstrasse 41 D - 22926 Ahrensburg 08/24/2016 6. Edition, ID No.: 37020GB-F...
- Page 87 • Fax: +49 (0)4102/807-189 © 2009 General Electric Company. All Rights Reserved. Specifications and manuals are subject to change without notice. GE is a registered trademark of General Electric Company. Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not affiliated with GE.