Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cisco MWA1221
Summary of Contents for Cisco MWA1221
- Page 1 Cisco MWA1221 MoCA to Wireless Adapter...
-
Page 4: Table Of Contents
MWA1221 User Manual Overview........................Terms and Definitions....................Initialization and Operations ..................MWA1221 Mode Overview ................... 9 MWA1221 LED Sequence ..................... 9 Boot Mode ........................10 Connect Mode......................11 Normal Mode....................... 13 CDL Mode ........................15... -
Page 5: Overview
In this case, the MWA1221 is connected with the home gateway via MoCA (MoCA Backhaul mode) and it extends data coverage to other unmanaged devices which would otherwise be out of reach to the main gateway. - Page 6 Identify your Device: f you device requires troubleshooting in the future, your service provider may ask for the serial number. The serial number can be located on the label found at the bottom of the device. Front Panel: Multicolored LED...
- Page 7 Rear Panel: 10/100/1000 Ethernet port to connect to either the data Gateway for Ethernet backhaul or connect to a downstream device WPS Button - When pressed, initiates the wireless setup feature, which allows you to add new Wireless Protected Setup (WPS) compliant device to your home network MoCA 2.0 Interface to connect to the data gateway for MoCA backhaul...
-
Page 8: Terms And Definitions
In order to ensure consistent operation of MWA1221 devices, this section describes the specific conditions and sequences for startup of the MWA1221 under a set of nominal and anomalous operating conditions. The use of the term Mode within this specification is set of functional requirements that do not dictate any specific system or... -
Page 9: Mwa1221 Mode Overview
Blinking once a second PURPLE MoCA network formed or Connect Ethernet network broadcast. Blinking once a second Normal BLUE Solid YELLOW When the MWA1221 is actively downloading, Blinking once a second validating and writing to memory a new code object. -
Page 10: Boot Mode
The MWA1221 product supports the Boot Mode process as illustrated in the following figure: The MWA1221 would be in Boot Mode when power is first applied or a reboot/restart of code image has occurred. The MWA1221 supports maximum two code image stored within flash. The execution options are:... -
Page 11: Connect Mode
MWA1221 would transition to MoCA Backhaul Mode or Ethernet Backhaul Mode if the product has successfully entered Connect Mode. The MWA1221 product would use fixed 1150MHz channel for MoCA interface to join MoCA network by default. During IP address assignment stage, the MWA1221 supports IPv6 and IPv4 on both interfaces. - Page 12 The MWA1221 would be assigned both DHCPv4 address and IPv6 link-local address if DHCPv4 is successful. MWA1221 uses UPnP protocol to discovery the uplink home gateway. If it is found, the MWA1221 product would enter MoCA Backhaul Mode if MoCA Interface is UP state, otherwise the MWA1221 would enter Ethernet Backhaul Mode.
-
Page 13: Normal Mode
When connected with gateway from MoCA interface or Ethernet interface, MWA1221 will enter Normal Mode. MWA1221 will try to detect whether the connected gateway support AutoSync feature via UPnP message. The Wi-Fi configuration could be synced from gateway following Specific “Wi-Fi AutoSync” protocol, or set manually on web GUI. - Page 14 WPS Method WPS Pin Code MWA1221 also provides Web GUI for User to configure Wi-Fi. If gateway does not support “Wi-Fi AutoSync” feature, MWA1221 will enable Wi-Fi by default configuration. User could change Wi-Fi configuration from Web GUI.
-
Page 15: Cdl Mode
MWA1221 supports TR069 Download RPC method as defined in TR069 Requirement Specification: Broadband Devices. User would write the image into a backup image location only. The MWA1221 would transition to Boot Mode after successfully writing an ingested code image to flash.