Sharp MX-C250F Technical Handy Manual page 51

SHARP
55 MFP Data Setting
2 Scanner soft switch setting
3 Controller soft switch setting:-
SW1-5 Auto clear function before copy
job execution:-
0 =Disabled, 1 = Enabled
SW3-6 Process mixed original size
printing for duplex mode:-
0 =Disabled, 1 = Enabled
SW3-7 HP Compatibility Mode:-
0 =Disabled, 1 = Enabled
SW6-1 Ethernet Speed Auto
negotiation:-
0 = Enabled, 1 = Disabled
SW6-2 Ethernet Link Speed:-
0 = 100Base TX, 1 = 10Base T
SW6-3 Ethernet Duplex Mode:-
0 = Full, 1 = Half
SW6-4 Ethernet 100/1000 Link Speed:-
0 = 100Base TX, 1 = 1000Base T
SW9-5 Maintenance notification setting
by Printer MIB:-
0 = Enabled, 1 = Disabled
SW9-6 Duplex Binding control:-
0:Binding OFF (Default)
1:Binding ON
SW18-6 Hide Device Counter Clear
(SIM24-6 to 24-15)
0 = Hide [Default], 1 = Display
SW22-5 Display toner remaining (MFP
Status)
0= Disabled, 1 = Enabled/Display
SW24-7 Continuous print mode for OSA
(job queuing for external
accounting)
0 = Job Queue Disabled
1 = Job Queue Enabled
SW25-7 Custom Envelope size (Printer).
0 = Disabled, 1 = Enabled
SW27-8 Retain Scan to Desktop
destination after a scan.
[MX-C301W]
0 = Disabled (Default)
1 = Enabled
SW28-3 Single Email alert notification for
customer.
0 = Disabled (Default)
1 = Enabled
10 Special Stamp setting (Taiwan only)
:-
[MX-C301W]
:-
[MX-C301W]
.
TEST SIMULATION
56 MFP Data Import & Export
1 Transfer data execute (MFP/SD Card/SRAM
& EEPROM)
[MX-C301W]
2 Export/Import EEPROM/SD Card/HDD data
3 Document filing backup to USB
4 Job log data backup to USB
5 Export Adjustment & Settings data to USB
6 Output Jam/Trouble data
7 Export Syslog data to USB
60
Memory Operation & Test
1 SDRAM read/write test (MFP PWB)
61
LSU Writing Adjustment/Test
1 LSU test (Polygon & BD detection check)
3 LSU power auto setup
4 LSU position adjustment (CMYK)
62
HDD Operation & Test [MX-C301W]
1 HDD/SD Card format
2 HDD partial read/write check
3 HDD read/write check (all areas)
6 Smart (HDD) self diagnostic test
7 Smart (HDD) self diagnostic error log
8 HDD/SD Card format (excluding system &
operation manual area)
10 Job completion list deletion (with job log)
11 Document filing data deletion
12 Enable/disable auto format for HDD trouble
13 HDD format (manual area only)
14 Delete document filing management data
63
CCD Operation & Adjustment
1 Shading correction data display
2 Shading correction execution (force)
3 CCD gamma & colour correction adjust.
5 CCD gamma & colour correction reset
12 B/W Image (RGB) ratio for lamp adjustment
[MX-C250/300]
64
Self Test Print
1 Test print (Colour mode)
2 Test print (B/W mode)
4 Printer self print test
5 Printer self print test (PCL)
6 Printer self pint test (PS)
7 Adjustment pattern print (Sim46-21)
[MX-C301W]
[MX-C301W]
[MX-C301W]
[MX-C301W]
[MX-C301W]
51