NEC SL1000 Hardware Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Cordless Telephone
  5. SL1000
  6. Hardware manual

NEC SL1000 Hardware Manual

Hide thumbs Also See for SL1000:
Table of Contents

Advertisement

Quick Links

See also: Programming Manual , User Manual
Hardware Manual
A50-031170-001 GE
ISSUE 3.0
November 2012

Advertisement

Table of Contents
loading

Related Manuals for NEC SL1000

Summary of Contents for NEC SL1000

  • Page 1 Hardware Manual A50-031170-001 GE ISSUE 3.0 November 2012...
  • Page 2 Copyright NEC Corporation reserves the right to change the specifications, functions, or features at any time without notice. NEC Corporation has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Corporation and shall not be reproduced without prior written approval of NEC Corporation.

  • Page 3: Table Of Contents

    ISSUE 3.0 SL1000 TABLE OF CONTENTS Regulatory Chapter 1 Introduction Section 1 GENERAL INFORMATION..........1-1 Section 2 EQUIPMENT LIST............. 1-2 2.1 KSUs and Optional Unit..............1-3 2.1.1 IP4[ ]-1632M-A KSU..............1-3 2.1.2 IP4[ ]-1632ME-A EXP..............1-4 2.1.3 IP4WW-EXIFB-C1................. 1-4 2.1.4 IP4WW-Battery Box..............1-5 2.2 Trunk/Extension/ISDN Expansion Interface Cards......
  • Page 4 SL1000 ISSUE 3.0 1.3.3 Mounting Procedure of KSU............2-6 1.4 Installing the Expansion KSU(s)............. 2-9 1.4.1 General..................2-9 1.4.2 Unpacking (EXIFB-C1)..............2-9 1.4.3 Connectors Location (EXIFB-C1)..........2-9 1.4.4 Installing the EXIFB-C1 PCB............2-9 1.4.5 KSUs Inter-connection..............2-12 1.5 Grounding and AC Cabling............2-12 1.5.1 Grounding the KSU..............
  • Page 5 ISSUE 3.0 SL1000 4.1.2 Unpacking................... 2-60 4.1.3 Installing the MEMDB PCB............2-60 4.2 VoIP Card (VOIPDB-C1) ............. 2-63 4.2.1 General..................2-63 4.2.2 Unpacking................... 2-63 4.2.3 Installing the VOIPDB-C1 PCB........... 2-63 4.2.4 LED Indication................2-67 4.3 VRS/Voice Mail Card (PZ-VM21)..........2-68 4.3.1 General..................
  • Page 6 SL1000 ISSUE 3.0 2.3 Saving (Backup) the Customer Data..........3-4 2.4 Loading the Customer Data............3-5 Section 3 SYSTEM SHUT DOWN............. 3-7 3.1 Powering Off the System..............3-7 3.2 Resetting the System..............3-7 Chapter 4 Maintenance Section 1 FUSE REPLACEMENT............. 4-1 1.1 Replacing the Fuse.................
  • Page 7 ISSUE 3.0 SL1000 LIST OF TABLES Table 1-1 Memory Capacity of MEMDB-C1............... 1-6 Table 1-2 System Capacity....................1-10 Table 2-1 KSU Packing List....................2-2 Table 2-2 Items on the CPU card..................2-3 Table 2-3 EXIFB-C1 Packing List..................2-9 Table 2-4 Connectors of EXIFB-C1................... 2-9 Table 2-5 Power Requirement..................
  • Page 8 SL1000 ISSUE 3.0 LIST OF FIGURES Figure 1-1 System Configuration..................1-1 Figure 1-2 System Image....................1-12 Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI)..................... 1-13 Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI)......................
  • Page 9 ISSUE 3.0 SL1000 Figure 2-46 Mounting the Battery Box................2-32 Figure 2-47 Securing the Battery Box................2-33 Figure 2-48 Removing the Front Cover ................2-33 Figure 2-49 Removing the L-Bracket ................2-34 Figure 2-50 Securing the L-Bracket and WM Hook............2-35 Figure 2-51 Attaching the KSU..................
  • Page 10 SL1000 ISSUE 3.0 Figure 2-99 Removing the Main-Cover................2-69 Figure 2-100 Removing the CPU Card................2-70 Figure 2-101 Installing the PZ-VM21 PCB............... 2-70 Figure 2-102 Installing the CPU Card................2-71 Figure 2-103 Replacing the Main-Cover................2-71 Figure 2-104 Installing the CF Card................. 2-72 Figure 2-105 Multiline Telephone (12TXH/24TXH/24TIXH (IP)) ........
  • Page 11 ISSUE 3.0 SL1000 Figure 4-5 Warning of Low Battery..................4-4 Figure 4-6 Removing the Sub-Cover................. 4-5 Figure 4-7 Disconnecting the AC Power Cord..............4-5 Figure 4-8 Removing the Main-Cover................4-6 Figure 4-9 Removing the CPU Card.................. 4-6 Figure 4-10 Location of Lithium Battery Socket..............4-7 Figure 4-11 Removing the Lithium Battery................

  • Page 12: Sl1000 Issue

    SL1000 ISSUE 3.0 MEMO Hardware Manual...

  • Page 13: Regulatory

    ISSUE 3.0 SL1000 Regulatory BATTERY DISPOSAL The SL system includes the batteries listed below. When disposing of these batteries, KSU, and/or Unit, you must comply with applicable regulations relating to your location regarding proper disposal procedures. Unit Name Type of Battery...
  • Page 14 For an overview of the supported features, refer to the detailed documentation that comes with this system, contact your local NEC Unified Solutions representative or the support desk of NEC Unified Solutions.

  • Page 15: Battery Information

    If your electrical and electronic products must be disposed of please refer to your supplier or the contractual agreements that your company has made upon acquisition of these products. At www.nec-unified.com/weee you can find information about separate disposal and environmentally sound recycling. BATTERY INFORMATION Defective or exhausted batteries should never be disposed of as municipal waste.
  • Page 16 SL1000 ISSUE 3.0 MEMO Regulatory...

  • Page 17: Chapter 1 Introduction

    Introduction 1 GENERAL INFORMATION ECTION Designed to support small/medium businesses with simple installation and easy operation. Small compact KSU comes with basic configuration of CPU, four analog trunk ports and eight hybrid extension ports and has three stackable slots for further expansion. The system can be increased to a maximum of 48 analog trunks and 96 Multiline extensions by adding up three more expansion KSUs, also equipped to support Digital Network (BRI/PRI, E1), IP Trunks (SIP/H.323) and IP extensions.

  • Page 18: Section 2 Equipment List

    SL1000 ISSUE 3.0 2 EQUIPMENT LIST ECTION The following table lists all equipment for the SL1000 system. Stock Number Equipment Name Equipment Description Note BE110231 IP4WW-1632M-A KSU IP4WW-1632M-A KSU without AC Cable 1101010 w/o C <Including> IP4WW-CPU-A1, IP4WW-408M-A1, Pow- er Supply...

  • Page 19: Ksus And Optional Unit

    ISSUE 3.0 SL1000 Stock Number Equipment Name Equipment Description Note BE110263 IP4WW-24TXH-A-TEL 4-wire 24-key Multiline Telephone 1101062 (WH) BE110264 IP4WW-24TXH-A-TEL 1101063 (BK) BE110277 IP4WW-24TIXH-C-TEL 24-Keys, Multiline IP Telephone (V1.2 Added) 1100160 (WH) BE110278 IP4WW-24TIXH-C-TEL 1100161 (BK) BE111129 IP4U-24TIXH-C-TEL 24-Keys, Multiline IP Telephone (V1.2 Added)

  • Page 20: Ip4[ ]-1632Me-A Exp

    SL1000 ISSUE 3.0 • CPU with main software (CPU-A1) • Power supply (110V/240V) • 1 External backup battery connector • 3 mounting spaces for 408E/008E/000E/1PRIU (3rd Slot of each KSU can not use for 4-Wire Multiline Telephone or DSS Console.) •...

  • Page 21: Ip4Ww-Battery Box

    ISSUE 3.0 SL1000 2.1.4 IP4WW-Battery Box Connected to each KSU power supply, the external backup battery provides DC power in case a loss of AC power occurs. An optional (locally procured), external battery source can be used to provide power during a power failure.

  • Page 22: Ip4Ww-000E-A1

    SL1000 ISSUE 3.0 2.2.3 IP4WW-000E-A1 This is an expansion card for mounting 2BRIDB board, and is installed into 1632M KSU/1632ME EXP. • Install this card to the expansion card slot at Main/ Expansion KSU • One ISDN BRI daughter board connection 2.2.4 IP4WW-2BRIDB-C1...

  • Page 23: Ip4Ww-Voipdb-C1

    ISSUE 3.0 SL1000 The MEMDB is mounted on the CPU card and provides the SDRAM and Flash Memory required by the following: • Expansion KSU(s) • VoIP • CTI • Remote Upgrade (main software) • VRS Channel Increment • InMail Channel Increment 2.3.2 IP4WW-VOIPDB-C1...

  • Page 24: Multiline Telephones And Optional Equipment

    SL1000 ISSUE 3.0 2.4 Multiline Telephones and Optional Equipment 2.4.1 IP4WW-12TXH-A TEL The 12TXH-A TEL is a 4-wire multiline telephone featuring: • Programmable keys: 12 • LCD: 16 digits x 2 lines • Handsfree: Half-duplex • Backlit dial pad: No •...

  • Page 25: Dp-D-1D

    ISSUE 3.0 SL1000 2.4.5 DP-D-1D This is the Doorphone Box. • Connects to hybrid port number 6 or 7 on the 408M of each KSU. Hardware Manual...

  • Page 26: Section 3 System Capacity

    SL1000 ISSUE 3.0 3 SYSTEM CAPACITY ECTION 3.1 System Capacity Table 1-2 System Capacity Items 1 KSU 2 KSU 3 KSU 4 KSU Note (1632) (3264) (4896) (64128) Expansion Slot *4th slot of each KSU can not be used for 4w Key Set.

  • Page 27: Ksu Capacity

    ISSUE 3.0 SL1000 Items 1 KSU 2 KSU 3 KSU 4 KSU Note (1632) (3264) (4896) (64128) Station Port 4W Key Set Max. 24/KSU SLT (–28V) 1KSU: 408M+408Ex3 2KSU: 408Mx2+408Ex6 3KSU: 408Mx3+408Ex9 4KSU: 408Mx4+408Ex12 BRI (S-Point) 1KSU: 2BRIx3 on 008E/000E...

  • Page 28: Figure 1-2 System Image

    SL1000 ISSUE 3.0 Expansion Interface Card x 3 Mother Board Mother Board 408M : Trunk x 4, Extension x 8 Expansion Interface Card 408E : Trunk x 4, Extension x 8 008E : Extension x 8 (Optional 2BRIDB ISDN BRI x 4),...

  • Page 29: Expandability Of Trunk And Extension (Without Pri)

    ISSUE 3.0 SL1000 3.2.1 Expandability of Trunk and Extension (without PRI) System Wide (Trunk) 1632ME EXP (3rd Exp. KSU) 1632ME EXP (Not trunk (2nd Exp. KSU) 1632ME EXP support) (1st Exp. KSU) 1632M KSU (Extension) Detail of one KSU Example 1: 408 x 4...

  • Page 30: Expandability Of Trunk And Extension (With Pri)

    SL1000 ISSUE 3.0 3.2.2 Expandability of Trunk and Extension (with PRI) System Wide (Trunk) 1632ME EXP (3rd Exp. KSU) 1632ME EXP (Not trunk (2nd Exp. KSU) 1632ME EXP support) (1st Exp. KSU) 1632M KSU (Extension) Detail of one KSU Example 1: 408 x 3, 2BRIDB x 2, PRI x 1 (3rd opt.

  • Page 31: Chapter 2 Installation

    Installation 1 INSTALLING THE MAIN & EXPANSION KSU ECTION 1.1 Before Installing the KSU(s) 1.1.1 General Precautions • To avoid shock or equipment damage, do not plug in or turn the system power on before completing the installation process. • Avoid working with the Equipment during electrical storms. •...

  • Page 32: Environmental Requirements

    SL1000 ISSUE 3.0 1.1.4 Environmental Requirements Meeting established environmental standards maximizes the life of the system. Make sure that the site is not: • In direct sunlight or in hot, cold or humid places. • In dusty areas or in areas where sulfuric gases are produced.

  • Page 33: Wall-Mounting The Ksu(S)

    ISSUE 3.0 SL1000 CPU card Sub-Cover < Front view > Figure 2-1 CPU Card Location Table 2-2 Items on the CPU card Item Description S1 (LOAD) Switch for System Restart/System Reset (Cold start occurs)/Upload Software Ethernet Cable Connection (for SMDR (PC, Printer), PCPro or WebPro….etc) Pin No.

  • Page 34: Wall Installation Of Ksu

    SL1000 ISSUE 3.0 290 mm (11.417) 115 mm (4.528) 375 mm (14.764) Figure 2-2 Dimension of the Main and Expansion KSU 1.3.2 Wall Installation of KSU The Main KSU (1632M-A) and Expansion KSU(s) (1632ME-A) be mounted on the wall. Before installing, ensure the appropriate spacing exists as shown below.

  • Page 35: Figure 2-3 Vertical Arrangement Of Ksus

    ISSUE 3.0 SL1000 Ceiling Minimum 200 mm (7.874) for ventilation EXP. KSU Minimum 100 mm (3.937) for ventilation and wiring Main KSU Minimum 300 mm (11.811) Minimum 300 mm (11.811) Minimum 100 mm (3.937) Wall EXP. KSU for ventilation and wiring Minimum 100 mm (3.937)

  • Page 36: Mounting Procedure Of Ksu

    SL1000 ISSUE 3.0 Ceiling Minimum 200 mm (7.874) for ventilation Minimum Minimum Minimum Minimum Minimum 300 mm 100 mm 100 mm 100 mm 300 mm (11.811) (3.937) (3.937) (3.937) (11.811) Wall Main KSU EXP. KSU EXP. KSU EXP. KSU Minimum 200 mm (7.874)

  • Page 37: Figure 2-6 Screw Positions

    ISSUE 3.0 SL1000 Install four screws into the wall. The screw heads must stand off from the wall about 2.5 mm (0.098″) to 3.5 mm (0.138″). 2.5 mm (0.098) - 3.5 mm (0.138) 285 mm (11.221) 180 mm (7.087) 285 mm (11.221) Figure 2-6 Screw Positions •...

  • Page 38: Figure 2-8 Removing The Sub-Cover

    SL1000 ISSUE 3.0 Pull out the Sub-Cover by pushing out the tabs. Sub-Cover Figure 2-8 Removing the Sub-Cover • The Sub-Cover can be opened and held in the open position. Push to hold Open Figure 2-9 Sub-Cover Open Position Align the four holes on the back of the KSU with the four screws installed in the wall.

  • Page 39: Installing The Expansion Ksu(S)

    ISSUE 3.0 SL1000 1.4 Installing the Expansion KSU(s) 1.4.1 General Each Expansion KSU is connected to the Main KSU individually. The EXIFB-C1 card and the MEMDB-C1 card must be installed in the Main KSU (1632M-A) . (Refer to Installing the Expansion...

  • Page 40: Figure 2-12 Removing The Sub-Cover

    SL1000 ISSUE 3.0 Open and pull out the Sub-Cover of the Main KSU. Sub-Cover Sub-Cover Figure 2-12 Removing the Sub-Cover Loosen two screws and pull out the Main-Cover by pressing the two hooks. Main-Cover Two screws Hooks Figure 2-13 Removing the Main-Cover...

  • Page 41: Figure 2-14 Exifb-C1 Pcb Installation

    ISSUE 3.0 SL1000 Press tab A and lift the CPU support bracket. EXIFB-C1 PCB CPU support CPU support 408M-A1 at 1632M KSU Figure 2-14 EXIFB-C1 PCB Installation Insert the EXIFB-C1 PCB into the J1 connector on the 408M-A1 at 1632M-A KSU.

  • Page 42: Ksus Inter-Connection

    SL1000 ISSUE 3.0 1.4.5 KSUs Inter-connection Connect the Main KSU (1632M-A) and Expansion KSU (1632ME-A) using the cables attached to the Expansion KSU. Exp. KSU No.1 (1632ME-A) EXIFE-C1 PCB < Bottom View > Main KSU (1632M-A) EXIFB-C1 PCB CPU card...

  • Page 43: Grounding The Ksu

    ISSUE 3.0 SL1000 1.5.1 Grounding the KSU Ensure all Main and Expansion KSU(s) are powered off and unplug the AC cord. In each KSU, connect the ETH lug to the verified grounding point using a minimum cable size of 14AWG (Φ2.0 mm) wire.

  • Page 44: Ac Power Cord

    SL1000 ISSUE 3.0 110 VAC 220 VAC 230 VAC 240 VAC Feeding Volt- SLT: 20 mA/-27 V AC Input I Main KSU = 1.31 A Main KSU = 0.78 A Main KSU = 0.76 A Main KSU = 0.73 A 4 KSU Total = 5.24 A...

  • Page 45: Precautions For Cabling

    ISSUE 3.0 SL1000 1.6.2 Precautions for Cabling • Do not wire the cable with an AC cable, computer, etc. • Do not run the cable near a high frequency generating device. • Use cable protectors in case the cables are run on the floor.

  • Page 46: Extension Cabling

    SL1000 ISSUE 3.0 Insert the modular plugs of the trunk line cords into the analog trunk modular jacks on the system. Modular Plug Wire Position for each Port Trunk Port Position CO2 or Audio in/out (External paging) CO3 or Audio in...

  • Page 47: Power Failure Transfer

    ISSUE 3.0 SL1000 Insert the modular plugs of the extension line cords (2-wire/4-wire) into the extension modular jacks on the KSU. Wire Position for each Port Extension Port Position T : Tip R : Ring ST6 or Doorphone/Sensor H : High...

  • Page 48: Figure 2-23 Pf/Kt Switch Of 408M-A1

    SL1000 ISSUE 3.0 Trunk Port No. 1 Extension Port No. 8 • The connected extension must be SLT (Single Line Telephone). • Hardware switch (J6) must be set from "KT" to "PF" side (default: KT) when use the Power failure transfer circuit.

  • Page 49: Cable Routing And Clamping

    ISSUE 3.0 SL1000 1.6.6 Cable Routing and Clamping Depending on cabling requirement, select either a right or left route. Clamp and route cable to outside. Cable clamp Cables Figure 2-24 Cabling Cut and remove the Plastic Knockouts as needed from the Sub-Cover.

  • Page 50: Section 2 Installing The External Backup Battery

    • Each KSU must have own IP4WW-Battery Box. To avoid damage to equipment, do not install the Topaz Battery Box (DX2E-32i/NX7E Battery Box) to the SL1000 system. 2.2 Unpacking Unpack the IP4WW-Battery Box and check it against the following list. Inspect for physical damage.

  • Page 51: Battery Box Dimensions

    ISSUE 3.0 SL1000 2.3 Battery Box Dimensions 230 mm (9.055) 340 mm (13.386) 500 mm (19.685) Figure 2-26 Dimension of the IP4WW-Battery Box 2.4 Battery Specifications Table 2-7 Battery Specifications Item Data Capacity 12 V, 7.0 Am/H or equivalent (Voltage must be 12 V) Recommended Battery GS Yuasa NP7-12 (151 x 65 x 97.5 mm / 2.7 kg)

  • Page 52: Figure 2-27 Removing The Front Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Front Cover. Two screws (with stopper) Front Cover Figure 2-27 Removing the Front Cover Disconnect the Battery Connection Cable from the Fuse Unit if the cable is plugged already. Battery Connection Cable...

  • Page 53: Figure 2-29 Batt Stopper

    ISSUE 3.0 SL1000 Loosen the screw and lift the Batt Stopper. Batt Stopper Screw Figure 2-29 Batt Stopper Pull out the Battery tray. Battery tray Figure 2-30 Pulling out the Battery Tray Loosen two screws and remove the Battery tray cover.

  • Page 54: Figure 2-31 Remove The Battery Tray Bracket

    SL1000 ISSUE 3.0 Remove two screws and remove the Battery tray bracket. Two screws (with stopper) Battery tray cover Two screws (M3 X 8) Battery tray bracket Figure 2-31 Remove the Battery Tray Bracket Install two batteries into the Battery tray.

  • Page 55: Figure 2-33 Connecting The Battery Cables

    ISSUE 3.0 SL1000 Connect the battery cables. Battery Connection Cable (black) Terminal Terminal (black) (black) Battery Connection Cable (red) Terminal Terminal (red) (red) Battery Connection Cable (blue) Two batteries < Front View > Figure 2-33 Connecting the Battery Cables Incorrect installation of batteries may damage the Fuse Unit or cause possible fire.

  • Page 56: Figure 2-35 Inserting The Battery Tray

    SL1000 ISSUE 3.0 11. Insert the Battery tray into the Battery Box. Battery tray Figure 2-35 Inserting the Battery Tray 12. Set the Batt Stopper bracket in place and secure with screw. Batt Stopper Screw Figure 2-36 Secure Batt Stopper Bracket...

  • Page 57: Mounting The Ip4Ww-Battery Box

    ISSUE 3.0 SL1000 13. Plug the Battery Connection Cable into the Fuse unit. Battery Connection Cable Fuse unit Figure 2-37 Connecting the Battery Connection Cable 14. Align tabs a to f to holes A to F on Battery Box. Slide the Front cover and tighten the two screws.

  • Page 58: Figure 2-39 Bases And Support Of The Battery Box

    SL1000 ISSUE 3.0 Assemble the FM/WM Base-F, Base-R and WM Support. FM/WM Base-R WM Support FM/WM Base-F Figure 2-39 Bases and Support of the Battery Box Refer to Figure 2-40 Floor-Mount Spacing Guide on page 2-28 for required spacing before drilling holes for 10 mm (0.394″) anchor bolts (locally procured).

  • Page 59: Wall-Mounting The Ip4Ww-Battery Box

    ISSUE 3.0 SL1000 Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box on the Base. IP4WW-Battery Box Hooks Hooks FM/WM Base FM/WM Base Hooks Hooks Figure 2-41 Mounting the Battery Box Using four supplied screws, secure the IP4WW-Battery Box to the FM/WM Base.

  • Page 60: Figure 2-43 Assemble Battery Box Base

    SL1000 ISSUE 3.0 Plywood should first be installed on the wall where the Battery Box will be positioned. This allows secure anchoring of the screws which support the weight of the Battery Box. Using four supplied screws, secure the WM Support to the FM/WM Base-F and Base-R.
  • Page 61 ISSUE 3.0 SL1000 Using anchor bolts, secure the FM/WM Base to the wall. Wall Front side Front side Anchor bolt location AC inlet AC inlet side side Anchor bolt location Four Anchor bolts M10 mm (0.394) : Maintenance space Figure 2-44 Wall-Mount Spacing Guide...

  • Page 62: Figure 2-45 Removing The Front Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Front Cover. Two screws (with stopper) Front Cover Figure 2-45 Removing the Front Cover Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box to the Base. Square hole...

  • Page 63: Mounting One Ksu On The Battery Box

    ISSUE 3.0 SL1000 Using one supplied screw (M3x6 with washer), secure the back plane of the Battery Box to the FM/WM Base. Two screw holes (Use either one) < Front view> Figure 2-47 Securing the Battery Box 2.6.3 Mounting One KSU on the Battery Box Before wall-mounting or floor-mounting the IP4WW-Battery Box, a single KSU can be mounted on the Battery Box.

  • Page 64: Figure 2-49 Removing The L-Bracket

    SL1000 ISSUE 3.0 Loosen two screws and remove the L-Bracket. L-Bracket Two screws (M4 X 8) Figure 2-49 Removing the L-Bracket Turn the L-Bracket upside down. Rotate the L-Bracket 180 degrees so that the upper FACE as shown in Figure 2-49 Removing the...

  • Page 65: Figure 2-50 Securing The L-Bracket And Wm Hook

    ISSUE 3.0 SL1000 Using two anchor bolts (locally procured), secure the WM Hook to the wall. The WM Hook is required for securing both Floor-mount and Wall-mount cases. Anchor Bolts WM Hook Two screws (M4 X 8) L-Bracket Two screws...

  • Page 66: Ip4Ww-Battery Box To Ksu Connection

    2.7 IP4WW-Battery Box to KSU Connection To avoid damage to equipment, do not install the Topaz Battery Box (DX2E-32i/NX7E Battery Box) to the SL1000 system. • Make sure the system power is off. • If Expansion KSU(s) are installed, turn the power on/off in the order of Expansion 3 KSU, Expansion 2 KSU, Expansion 1 KSU and then Main KSU.

  • Page 67: Ip4Ww-Battery Box Fuse Replacement

    ISSUE 3.0 SL1000 Cut and remove Plastic Knockout from the Sub-Cover to connect Battery cable. Plastic Knockout Sub-Cover Battery cable Figure 2-54 Connecting Battery Cable Connect Battery cable from the Battery box to Battery connector on the KSU. 2.8 IP4WW-Battery Box Fuse Replacement •...

  • Page 68: Figure 2-55 Removing The Front Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Front Cover. Two screws (with stopper) Front Cover Figure 2-55 Removing the Front Cover Disconnect the Battery connection cable from the Fuse Unit. Battery Connection Cable Fuse Unit Figure 2-56 Disconnecting the Battery Connection Cable...

  • Page 69: Figure 2-57 Loosen The Fuse Unit Screw

    ISSUE 3.0 SL1000 Loosen the screw from the Fuse Unit. Fuse Unit Screw Figure 2-57 Loosen the Fuse Unit Screw Slide Fuse Unit out of the Battery box. Replace the fuse (250VT8AL). Fuse Unit 250VT8AL Fuse Fuse Unit guide Figure 2-58 Replacing the Fuse Using the Fuse Unit guides, slide the Fuse Unit into the Battery Box.

  • Page 70: Figure 2-60 Securing The Fuse Unit

    SL1000 ISSUE 3.0 Secure the Fuse Unit by tightening the screw. Fuse Unit Screw Figure 2-60 Securing the Fuse Unit Reconnect the Battery Connection Cable to the Fuse Unit. Battery Connection Cable Fuse Unit Figure 2-61 Connect Battery Connection Cable...

  • Page 71: Figure 2-62 Installation Of The Front Cover

    ISSUE 3.0 SL1000 10. Align tabs a to f to holes A to F on Battery Box. Slide the Front Cover into position and tighten the two screws. Front cover Two screws (with stopper) Figure 2-62 Installation of the Front Cover...

  • Page 72: Cards

    SL1000 ISSUE 3.0 3 INSTALLING THE EXPANSION INTERFACE CARDS ECTION 3.1 General Up to three expansion interface cards can be installed per KSU. Table 2-8 Expansion Cards Expansion Interface Description Note Card IP4WW-408E-A1 4 analog trunks and 8 hybrid extensions card...

  • Page 73: Mounting The Expansion Interface Card

    ISSUE 3.0 SL1000 Items List of Contents IP4WW-2BRIDB-C1 2BRIDB-C1 PCB Nylon Spacers 2BRI Label Metal Spacers Screws (with circular washer) IP4WW-1PRIU-C1 1PRIU-C1 PCB (with PKG Spacer) Nylon Spacers Metal Spacers Screws (with circular washer) 3.3 Mounting the Expansion Interface Card DO NOT POWER ON until all installation has been completed.

  • Page 74: Figure 2-64 Removing The Main-Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Main-cover. Main-Cover Two screws Hooks Figure 2-64 Removing the Main-cover Insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 408E/008E/000E/1PRIU) If no more Expansion Interface cards are to be mounted on the 1st PCB, fasten two screws to secure the 1st PCB on the top of the 408E/008E/000E/1PRIU.

  • Page 75: Figure 2-66 Mounting The 2Nd Expansion Interface Card

    ISSUE 3.0 SL1000 In case a 2nd PCB is mounted, insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 408E/ 008E/000E/1PRIU) If no more Expansion interface card is mounted on the 2nd PCB, fasten two screws to secure the 2nd PCB to the top of the 408E/008E/000E/1PRIU.

  • Page 76: Figure 2-67 Mounting The 3Rd Expansion Interface Card

    SL1000 ISSUE 3.0 In case a 3rd PCB is mounted, insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 408E/ 008E/000E/1PRIU) Fasten two screws to secure the 3rd PCB to the top of the 408E/008E/000E/1PRIU.

  • Page 77: Mounting The 2Bridb Pcb

    ISSUE 3.0 SL1000 Cut and remove the Plastic Knockouts as required for each Expansion interface card. EXP.1st PCB Main-Cover EXP.2nd PCB Plastic Knockouts EXP.3rd PCB Figure 2-69 Plastic Knockouts Replace the Main-cover and fasten two screws. Main-Cover Two screws Hooks Figure 2-70 Replacing the Main-cover 3.3.2 Mounting the 2BRIDB PCB...

  • Page 78: Figure 2-71 Plastic Knockouts On 008E-A1/000E-A1

    SL1000 ISSUE 3.0 Cut and remove specified Plastic Knockouts on the 008E-A1/000E-A1 PCB. Plastic Knockout 008E-A1 Plastic Knockouts 000E-A1 Figure 2-71 Plastic Knockouts on 008E-A1/000E-A1 Insert two Nylon-spacers into the specified holes. Using supplied screw, fasten Metal Spacer to 2BRIDB-C1 PCB.

  • Page 79: Cabling And Setting The Expansion Interface Card

    ISSUE 3.0 SL1000 Mount the 2BRIDB-C1 with 008E-A1/000E-A1 PCB into the KSU. Screws 008E-A1/000E-A1 PCB and 2BRIDB-C1 PCB Nylon- Spacers Metal-Spacers Figure 2-73 Mounting the 2BRIDB-C1 into the KSU Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks Figure 2-74 Replacing the Main-Cover 3.4 Cabling and Setting the Expansion Interface Card...

  • Page 80: Cabling Ip4Ww-408E-A1

    • Aerial distribution wiring is not allowed. • Trunks must be installed with lightning protectors. • Do not install the Topaz Terminal in the SL1000 system, it does not work properly. 3.4.1 Cabling IP4WW-408E-A1 This IP4WW-408E-A1 PCB provides four RJ11 connections for analog trunks and eight RJ11 connections for hybrid extensions.

  • Page 81: Cabling Ip4Ww-008E-A1

    ISSUE 3.0 SL1000 Wire Position Wire Position for each Port Extension Port Position Extension Port Position for each Port ST32 ST25 CO8/12/16 CO6/10/14 ST24 ST17 CO7/11/15 CO5/9/13 ST16 Trunk Port Extension Port CO16 CO13 ST32 ST25 3rd EXP. PCB CO12...

  • Page 82: Cabling Ip4Ww-000E-A1

    SL1000 ISSUE 3.0 Topaz Terminal does not work properly when it connected. Wire Position Extension Port Position for each Port ST32 ST25 ST24 ST17 ST16 Extension Port ST25 3rd EXP. PCB ST32 ST24 ST17 2nd EXP. PCB ST16 1st EXP. PCB...

  • Page 83: Table 2-10 Rj-61 Bri Pin-Outs (S-Bus, T-Bus)

    ISSUE 3.0 SL1000 BRI2 BRI1 ISDN BRI Figure 2-77 Connectors of 2BRIDB-C1 3.4.4.1 Connectors The following table shows the pin-outs for the RJ-61 cable connector for S-Bus and T-Bus connections. Table 2-10 RJ-61 BRI Pin-Outs (S-Bus, T-Bus) Pin No. RJ-61 Cable Connec-...

  • Page 84: Table 2-11 Switch Setting Of 2Bridb-C1

    SL1000 ISSUE 3.0 Set the switches J12 to J17 according to the system, referring the Table 2-11 Switch Setting of 2BRIDB-C1 on page 2-54. Table 2-11 Switch Setting of 2BRIDB-C1 Switch No. Switch Position Description J12/J15 ON (default) Termination register is ON.

  • Page 85: Cabling And Setting Ip4Ww-1Priu-C1

    ISSUE 3.0 SL1000 3.4.5 Cabling and Setting IP4WW-1PRIU-C1 This IP4WW-1PRIU-C1 PCB provides one RJ-45 PRI connection. PRI 1 PRI/E1/T1 Line Figure 2-79 Connector of 1PRIU-C1 3.4.5.1 Connector Following table shows the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus RJ-45 connections.

  • Page 86: Table 2-14 Led Indication

    SL1000 ISSUE 3.0 Assign whether the unit works as PRI/T1/E1 by PRG10-51-01. With normal operation, D4 LED flashes green. IP4WW-1PRIU-C1 1.5M 2M 1.5M J8/9 D3 D4 PRI 1 (Red) (Green) Figure 2-80 Switches and LEDs Location of 1PRIU-C1 3.4.5.3 LED Indication LED indications for the IP4WW-1PRIU-C1 are listed in following table.

  • Page 87: Table 2-15 T1 Led Indications

    ISSUE 3.0 SL1000 LED Indication Operation Status Remarks Live LED (D4) Busy LED (D3) (Green) (Red) Unit Busy A Channel is busy (use another from Ch1 - Chx) All channels are Idle. Flash 80ms (On/ Downloading firmware Off) x3/ 400ms T1 Alarm Mode Refer to following figure for LED pattern information.

  • Page 88: Power Failure Transfer (408E-A1 Only)

    SL1000 ISSUE 3.0 120 ms green green green green TS16 green 1 cycle 3.8 sec (120ms x 32=3840 ms) Figure 2-82 1PRIU-C1 LED Indication Pattern of Layer 1 on E1 Unit Table 2-16 E1 LED Indications Alarm Details of the alarm...

  • Page 89: Power Failure Setting

    ISSUE 3.0 SL1000 • The connected extension must be SLT (Single Line Telephone). • Hardware switch (J6) must be set from "KT" to "PF" side (default: KT) when use the Power failure transfer circuit. • Refer to Power Failure Transfer on page 2-17 for Power Failure Transfer of 408M-A1.

  • Page 90: Section 4 Installing The Optional Interface Cards

    SL1000 ISSUE 3.0 4 INSTALLING THE OPTIONAL INTERFACE CARDS ECTION 4.1 Installing the Expansion Memory Card (MEMDB-C1) 4.1.1 General The Memory expansion daughter board (IP4[ ]-MEMDB-C1) provides additional memory for the system to use following features; • A System with multiple KSUs •...

  • Page 91: Figure 2-85 Removing The Main-Cover

    ISSUE 3.0 SL1000 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-85 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 408M-A1 at 1632M KSU...

  • Page 92: Figure 2-87 Installing The Memdb Pcb

    SL1000 ISSUE 3.0 Insert the MEMDB-C1 daughter board to J4 socket on the CPU card and press down the MEMDB-C1 daughter board to secure. Both levers must be secured to notch-A. Notch-A Notch-B Lever MEMDB-C1 PCB CPU card Figure 2-87 Installing the MEMDB PCB Reinstall the CPU card into the 408M-A1 mother board, and close the CPU support making sure the tab A locks into place.

  • Page 93: Voip Card (Voipdb-C1)

    ISSUE 3.0 SL1000 Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks Figure 2-89 Replacing the Main-Cover 4.2 VoIP Card (VOIPDB-C1) (This item is for V1.2 or higher) 4.2.1 General The IP4WW-VOIPDB-C1 daughter board is used to convert the RTP (Real Time Transfer Protocol) packets via the IP Network and PCM highway.

  • Page 94: Figure 2-90 Removing The Sub-Cover

    SL1000 ISSUE 3.0 Open and remove the Sub-Cover. Sub-Cover Sub-Cover Figure 2-90 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-91 Removing the Main-Cover 2-64 Installation...

  • Page 95: Figure 2-92 Removing The Cpu Card

    ISSUE 3.0 SL1000 Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 408M-A1 at 1632M KSU Figure 2-92 Removing the CPU Card Install the VOIPDB-C1 daughter board to J5 connector on the CPU card.

  • Page 96: Figure 2-94 Installing The Cpu Card

    SL1000 ISSUE 3.0 Reinstall the CPU card into the 408M-A1 mother board, and close the CPU Support making sure tab A locks into place. CPU card CPU support 408M-A1 at 1632M KSU Figure 2-94 Installing the CPU Card Cut and remove the Plastic Knockout for VoIP connector, then replace the Main-Cover and fasten two screws.

  • Page 97: Led Indication

    ISSUE 3.0 SL1000 Connect the VOIPDB-C1 to an Switching hub using an LAN Cable. The LAN Cable must pass two times (two rounds) through the Ferrite Core as below. (Ferrite Core is attached with VOIPDB-C1) 30 - 50 mm VOIPDB-C1 board (CN1) (1.181 - 1.967)

  • Page 98: Vrs/Voice Mail Card (Pz-Vm21)

    SL1000 ISSUE 3.0 Table 2-19 VOIPDB LED Indications Function LED Status Operation status Link activity or data transmission and re- On Green LED lights when link up is completed. LED flash ception. when data is transmitting or receiving. LINK1000 1000Base-T link speed indicator On Yellow Lights up when 1000Base-T link up.

  • Page 99: Figure 2-98 Removing The Sub-Cover

    ISSUE 3.0 SL1000 Open and remove the Sub-Cover. Sub-Cover Sub-Cover Figure 2-98 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 2-99 Removing the Main-Cover Hardware Manual 2-69...

  • Page 100: Figure 2-100 Removing The Cpu Card

    SL1000 ISSUE 3.0 Press tab A and lift the CPU support bracket. Remove the CPU card. CPU card CPU support 408M-A1 at 1632M KSU Figure 2-100 Removing the CPU Card Connect the PZ-VM21 daughter board to the J6 connector using four Nylon-spacers on the CPU card.

  • Page 101: Installing The Cf Card (Cfvrs/Cfvms/Cfvml)

    ISSUE 3.0 SL1000 Reinstall the CPU card into the 408M-A1 mother board, and close the CPU Support making sure tab A locks into place. CPU card CPU support 408M-A1 at 1632M KSU Figure 2-102 Installing the CPU Card Replace the Main-Cover and fasten two screws.

  • Page 102: Figure 2-104 Installing The Cf Card

    SL1000 ISSUE 3.0 Remove the CPU card and insert the compact flash card into the CF slot (CN2). CF card CPU card CF Slot (CN2) PZ-VM21 PCB Figure 2-104 Installing the CF Card Reinstall the CPU card into the 408M-A1 mother board, and close the CPU Support making sure tab A locks into place.

  • Page 103: And Optional Terminals

    ISSUE 3.0 SL1000 5 INSTALLING THE MULTILINE TELEPHONES AND ECTION OPTIONAL TERMINALS 5.1 Installing the Multiline Telephones There are three types of Multiline Telephones available in the SL system. • IP4WW-12TXH-A-TEL • IP4WW-24TXH-A-TEL • IP4WW-24TIXH-C-TEL (IP) (V1.2 Added) 5.1.1 Location of Controls (24TIXH (IP) is for V1.2 or higher)

  • Page 104: Multiline Telephone Legs Adjustment

    SL1000 ISSUE 3.0 Functions 12TXH 24TXH 24TIXH SoftKeys Backlit Dial Pad Incoming LED 2 colors (Red/Green) Connected to Hybrid Extension Port Hybrid Extension Port Ethernet Port on the Network Headset Port Power Feeding AC Adapter (DC27 V,1 A) or PoE (IEEE802.3af)

  • Page 105: Figure 2-108 Setting For High Position

    ISSUE 3.0 SL1000 5.1.2.2 High position setting Turn telephone over (button side down). Pull up the Leg Stoppers. Leg Stopper Figure 2-108 Setting for High Position Adjust the leg to desired height. < High position > Figure 2-109 Leg Setting for High Position Lead the Line and Handset cords through the applicable grooves.

  • Page 106: Wall-Mounting The Multiline Telephone

    SL1000 ISSUE 3.0 5.1.3 Wall-Mounting the Multiline Telephone Arrange the cables and put down the leg as shown below. Handset cord Telephone line cord < Bottom view> Figure 2-110 Cabling for Wall-Mount For IP4WW-24TIXH-C only: (V1.2 Added) When wall-mounting the IP4WW-24TIXH-C, attach the IP4WW-WALL MOUNT UNIT to the bottom panel as shown.

  • Page 107: Figure 2-113 Wall-Mount Screw Guide

    ISSUE 3.0 SL1000 Remove the switch-hook from the unit. Turn the tab toward the top. Then slide the hook-switch into position. Refer to Figure 2-112 Hook-Switch Hanger on page 2-77. Hook-switch hanger Hook-switch hanger Figure 2-112 Hook-Switch Hanger Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″).

  • Page 108: Install The Ip Multiline Telephone (Ip4Ww-24Tixh-C1 Tel)

    SL1000 ISSUE 3.0 5.2 Install the IP Multiline Telephone (IP4WW-24TIXH-C1 TEL) (This item is for V1.2 or higher) 5.2.1 System Connection The IP Multiline Telephone is connected via HUB. IP Multiline Telephone Exit Help LAN Cable (10BASE-T/100BASE-TX) Flash Transfer Mute...

  • Page 109: Applying Power To The Ip Multiline Telephone

    ISSUE 3.0 SL1000 5.2.3 Applying Power to the IP Multiline Telephone IP Multiline Telephone (IP4WW-24TIXH-C1) supports two different power sources for the Telephone. • AC-LE UNIT Plug the Optional AC-[ ] AC adapter input jack in the telephone base unit, and plug the 2-prong wall plug of the AC adapter in AC outlet.

  • Page 110: Figure 2-118 Cabling Of Dss

    SL1000 ISSUE 3.0 Lead the Line cord through the applicable grooves. Figure 2-118 Cabling of DSS 5.3.1.2 High position setting Turn DSS Console over (button side down). Pull up the Leg Stoppers. Leg Stopper Figure 2-119 Leg Stopper of DSS Console...

  • Page 111: Wall-Mounting The Dss Console

    ISSUE 3.0 SL1000 Adjust the leg to desired height. < High position > Figure 2-120 High Position Setting Lead the Line cord through the applicable grooves. (Refer to Figure 2-118 Cabling of DSS on page 2-80) 5.3.2 Wall-Mounting the DSS Console Lift the leg and lead the cable through the applicable grooves.

  • Page 112: Installing The Headset

    SL1000 ISSUE 3.0 Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″). 3 - 4 mm 1 - 3 mm (0.12 - 0.16) (0.04 - 0.12) 83.5 mm (3.287) 7 - 9.5 mm (0.28 - 0.37)

  • Page 113: Installing The Doorphone Box

    <Recommended Headset> • HW251N-A10-NE This Item is made by Plantronics, inc. For the details of setting and operation, refer to the SL1000 Feature & Specifications Manual. (separate issue) The headset configuration is assigned using system programming. 5.5 Installing the Doorphone Box 5.5.1 Wall-Mounting the Doorphone...

  • Page 114: Figure 2-126 Doorphone Box And Bracket

    SL1000 ISSUE 3.0 Connect the cable to the screw terminals on the Doorphone box. (No polarity sensitive) Wall-mount bracket Upper housing Screw terminals Screw Connect cable Figure 2-126 Doorphone Box and Bracket Mount the Wall-Mount bracket on the wall using supplied screws.

  • Page 115: Connecting The Doorphone

    ISSUE 3.0 SL1000 5.5.2 Connecting the Doorphone Wire position for each port Port position ST6 or ST7 Modular cable (2-wire, Straight) Doorphone Figure 2-128 Connecting the Doorphone The Doorphone configuration is assigned using system programming. The 3 party Doorphone Boxes cannot be connected to the port.

  • Page 116: Table 2-24 Rj-61 General Purpose/Door Unlock Relay Control Connector (J7)

    SL1000 ISSUE 3.0 J7 (RJ61) 8 765 4321 RY1/2 Door unlock control devices Figure 2-129 Connecting the Door Unlock Device The following table shows the pin-outs for the RJ-61 cable connector. Table 2-24 RJ-61 General Purpose/Door Unlock Relay Control Connector (J7) Pin No.

  • Page 117: Installing The External Paging Speaker/External Moh/Bgm Sources

    ISSUE 3.0 SL1000 5.7 Installing the External Paging Speaker/External MOH/BGM Sources 5.7.1 Connecting the Audio Equipment • The trunk ports CO2 to CO4 can be used for audio port (External paging, External MOH, BGM) • Audio port configuration is assigned using system programming.

  • Page 118: Bgm/External Moh Source Input Specifications

    SL1000 ISSUE 3.0 Item Specification Maximum Output 400 mV RMS 5.7.3 BGM/External MOH Source Input Specifications Table 2-27 BGM/External MOH Source Input Specifications Item Specification Input Impedance 600 Ω @ 1 kHz Input Level Nominal 250 mV (-10 dBm) Maximum Input 1 V RMS 5.8 SMDR (Station Message Detail Recording)

  • Page 119: Chapter 3 System Start Up

    System Start Up 1 SYSTEM START UP ECTION 1.1 Before Starting Up the System Before starting up the system, make sure: • KSU(s) are installed correctly. • All extensions are cabled correctly. • All earth ground and PSTN Trunks are cabled correctly. •...

  • Page 120: Perform A Cold Start

    SL1000 ISSUE 3.0 1.2.1 Perform a Cold Start This section describes the process for starting the system for the first time or starting a system that requires the customer data be deleted. System software is loaded from flash memory, and the customer data is deleted from RAM memory.

  • Page 121: Perform A Hot Start

    ISSUE 3.0 SL1000 Turn the power switch ON at the Main KSU. Continue holding the LOAD button (S1) for approximately three seconds or until Status LED (D5) starts flashing red. RUN LED LED (D5) < Front view > Figure 3-4 Status LED (D5) and RUN LED Location Release the LOAD button.

  • Page 122: Section 2 Programming Mode

    SL1000 ISSUE 3.0 2 PROGRAMMING MODE ECTION 2.1 Entering the Programming Mode The installer/system administrator can enter to the system programming mode from the Display Type Multiline Telephone. (A maximum of two users can enter mode at the same time) In a newly installed system, use extension port 1.

  • Page 123: Loading The Customer Data

    ISSUE 3.0 SL1000 For the details of PZ-VM21 daughter board installation, refer to Installing the PZ-VM21 PCB on page 2-68. Turn the system power off, insert the blank CF card (32 MB or larger) to the CF slot on PZ-VM21.

  • Page 124: Figure 3-13 Inserting The Cf Card

    SL1000 ISSUE 3.0 Turn the power off, insert the Customer Data CF card into the CF Slot on PZ-VM21. CPU card CF Slot (CN2) CF card PZ-VM21 PCB Figure 3-13 Inserting the CF card Turn the power on, enter the Program Mode then PRG90-04.

  • Page 125: Section 3 System Shut Down

    ISSUE 3.0 SL1000 3 SYSTEM SHUT DOWN ECTION 3.1 Powering Off the System Turn the all KSU(s) power off using the power switch. Figure 3-16 Power Switch Location • If Expansion KSU(s) are installed, turn the power on/off in the order of Expansion 3 KSU, Expansion 2 KSU, Expansion 1 KSU and then Main KSU.

  • Page 126: Sl1000 Issue

    SL1000 ISSUE 3.0 MEMO System Start Up...

  • Page 127: Chapter 4 Maintenance

    Maintenance 1 FUSE REPLACEMENT ECTION 1.1 Replacing the Fuse This fuse is only for external battery box connection, it is not used for AC power to the system. If Expansion KSU(s) are installed, turn the power on/off in the order of Expansion 3 KSU, Expansion 2 KSU, Expansion 1 KSU and then Main KSU.

  • Page 128: Figure 4-2 Removing The Main-Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 4-2 Removing the Main-Cover Exchange the fuse (250 V/8 A) on 408M-A1 PCB. 408M-A1 FUSE (8 A / 250 V) < Top View > Figure 4-3 Exchanging the Fuse...

  • Page 129: Figure 4-4 Replacing The Main-Cover

    ISSUE 3.0 SL1000 Replace the Main-Cover and fasten two screws. Main-Cover Two screws Hooks Figure 4-4 Replacing the Main-Cover Hardware Manual...

  • Page 130: Section 2 Lithium Battery Replacement

    Before replacing the Lithium battery, make sure which type of Lithium battery is required and prepare the new Lithium battery. (CR2032) NEC recommends that a backup of the customer data is performed before powering off the system (either PCPro file or CF card backup) in order to replace the backup battery.

  • Page 131: Replacing The Lithium Battery

    ISSUE 3.0 SL1000 2.3 Replacing the Lithium Battery Remove the Sub-Cover at the Main KSU. Sub-Cover Figure 4-6 Removing the Sub-Cover Power off the system, and remove the AC plug from the AC outlet. Disconnect the AC power cord from the KSU.

  • Page 132: Figure 4-8 Removing The Main-Cover

    SL1000 ISSUE 3.0 Loosen two screws and remove the Main-Cover. Main-Cover Two screws Hooks Figure 4-8 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove CPU card from the Main KSU. CPU card CPU support 408M-A1 at 1632M KSU...

  • Page 133: Figure 4-10 Location Of Lithium Battery Socket

    ISSUE 3.0 SL1000 Refer to following figure for the Lithium battery location on the CPU card. CPU card Battery socket < Conductor side > Figure 4-10 Location of Lithium Battery Socket Remove the old Lithium battery and insert the new one into the socket.

  • Page 134: Figure 4-13 Installing The Cpu Card

    SL1000 ISSUE 3.0 Reinstall the CPU card into the 408M-A1 mother board and close the CPU support bracket. CPU card CPU support 408M-A1 at 1632M KSU Figure 4-13 Installing the CPU Card 10. Replace the Main-Cover and Sub-Cover. Maintenance...

  • Page 135: Section 3 Main Software Upgrading

    • Prepare the CF Card (32MB, or upwards and formatting by FAT(16)), and store the new main software on the CF card by PC. (New main system software is supplied by NEC.) • Install the PZ-VM21 PCB. (if the system does not have it.) 3.3 Main Software Version Confirmation...

  • Page 136: Upgrading The Main Software

    SL1000 ISSUE 3.0 3.4 Upgrading the Main Software If Expansion KSU(s) are installed, turn the power on/off in the order of Expansion 3 KSU, Expansion 2 KSU, Expansion 1 KSU and then Main KSU. Power off the system and disconnect the AC cord from the KSU.

  • Page 137: Table 4-1 Status Leds

    ISSUE 3.0 SL1000 Insert the CF card (with the new main system software loaded) to the CF slot on PZ-VM21 daughter board. (PZ-VM21 should be temporary installed if not already fitted.) CPU card CF Slot (CN2) PZ-VM21 PCB CF card...

  • Page 138: Figure 4-19 Removing The Cf Card

    SL1000 ISSUE 3.0 10. Turn the power off and remove the CF card from the CF slot on PZ-VM21. CPU card CF Slot (CN2) CF card PZ-VM21 PCB Figure 4-19 Removing the CF card 11. Replace the Main-Cover and Sub-Cover.

  • Page 139: Section 4 Led Indications

    ISSUE 3.0 SL1000 4 LED INDICATIONS ECTION The LEDs on the CPU indicate the following: • RUN (D1) = The CPU is operating (Blue) • D2, and D3 = Alarms (Red) • D4 = Flash access indication (Red) • D5 = Boot status (Red) •...
  • Page 140 SL1000 ISSUE 3.0 MEMO 4-14 Maintenance...

  • Page 141: Section 1 System Capacity

    Specifications 1 SYSTEM CAPACITY ECTION Table 5-1 System Capacity Items 1 KSU 2 KSU 3 KSU 4 KSU Note (1632) (3264) (4896) (64128) Expansion Slot *4th slot of each KSU can not be used for 4w Key Set. *4th KSU can not be used for COI, 2BRIDB and 1PRIU.

  • Page 142: Specifications

    SL1000 ISSUE 3.0 Items 1 KSU 2 KSU 3 KSU 4 KSU Note (1632) (3264) (4896) (64128) Station Port 4W Key Set Max. 24/KSU SLT (–28V) 1KSU: 408M+408Ex3 2KSU: 408Mx2+408Ex6 3KSU: 408Mx3+408Ex9 4KSU: 408Mx4+408Ex12 BRI (S-Point) 1KSU: 2BRIx3 on 008E/000E...

  • Page 143: Section 2 System Specifications

    ISSUE 3.0 SL1000 2 SYSTEM SPECIFICATIONS ECTION 2.1 General Precautions • Never attempt to insert wires, pins, etc. into the vents or other holes of the equipment. • Do not use benzene, thinner, or the like, or any abrasive powder to clean the equipment. Wipe it with a soft cloth.

  • Page 144: Electrical Specifications (Ksu)

    SL1000 ISSUE 3.0 110 VAC 220 VAC 230 VAC 240 VAC Frequency 47 Hz - 63 Hz (Rated Frequency:50/60 Hz) Phase and Wire Single Phase, 2 Line + PE Type Grounding Re- No.14 AWG Copper Wire quirement Feeding Volt- SLT: 20 mA/-27 V AC Input I Main KSU = 1.31 A...

  • Page 145: Traffic Capacity

    ISSUE 3.0 SL1000 2.8 Traffic Capacity Traffic Capacity Basic System Package Expanded System Package Traffic Capacity 2540 BHCA 2540 BHCA 2540 Busy-Hour Call Attempts (BHCA) is based on a Full Capacity. 2.9 IP Terminal Power Chart Table 5-5 IP Terminal Power Chart...

  • Page 146: Doorphone Interface Specifications

    SL1000 ISSUE 3.0 Unit Width Depth Height Weight Note IP4WW-VOIPDB-C1 66 mm 138 mm 18 mm 0.05 kg (2.60 in) (5.43 in) (0.71 in) (1.76 oz) PZ-VM21 53 mm 85 mm 13 mm 0.03 kg (2.09 in) (3.35 in) (0.51 in) (1.06 oz)

  • Page 147: Bgm/Exmoh Source Input Specifications

    ISSUE 3.0 SL1000 Item Specification Maximum Output 400 mV RMS 2.16 BGM/ExMOH Source Input Specifications Table 5-12 BGM/External MOH Source Input Specifications Item Specification Output Impedance 600 Ω @ 1 kHz Input Level Nominal 250 mV (-10 dBm) Maximum Input 1 V RMS 2.17 External Sensor Device Interface Specifications...

  • Page 148: Cable Requirements

    SL1000 ISSUE 3.0 2.20 Cable Requirements Table 5-15 Cable Requirements Device Cable Type Cable Run Length Multiline Telephone 24 AWG (Φ0.5 mm) 300 m (984.3 ft) Multiline IP Telephone CAT5 Straight Cable 100 m (328.1 ft) DSS Console 24 AWG (Φ0.5 mm) 300 m (984.3 ft)
  • Page 149 ISSUE 3.0 SL1000 MEMO Hardware Manual...
  • Page 150 Hardware Manual NEC Corporation ISSUE 3.0...

This manual is also suitable for:

Sl 1000

Table of Contents