Makita DML805 Instruction Manual page 3

Corded and cordless led worklight
Hide thumbs Also See for DML805:
Table of Contents

Advertisement

8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
9.
If external flexible cable or cord of this luminaire
is damaged, it shall be exclusively replaced by
authorized service center in order to avoid a hazard.
10. Do not look in the LED light or see the source of light
directly.
The lamp was classified at risk Group 1.
a)
The lamp or lamp system is in excess of the Exempt
Group and that the viewer related risk is dependent
upon how the users install and use the product;
b)
The most restrictive optical radiation hazard and
other optical radiation hazards in excess of Exempt
Group.
c)
Proper assembly, installation, maintenance and
safe use, including clear warnings concerning
precautions to avoid possible exposure to hazardous
optical radiation.
d)
Advice on safe operation procedures and warnings
concerning reasonably foreseeable malpractices,
malfunctions and hazardous failure modes.
e)
NOTICE: UV and IR emitted from this product.
f)
WARNING: IR emitted from this product.
g)
CAUTION: Possibly hazardous optical radiation
emitted from this product.
h)
Minimize exposure to eyes or skin. Use appropriate
shielding.
i)
Use appropriate shielding or eye protection.
j)
Do not stare at operating lamp. May be harmful to
the eyes.
k)
Eye or skin irritation may result from exposure. Avoid
eye exposure.
Battery tool use and care
1.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery cartridge may create a risk of fire when
used with another battery cartridge.
2.
Use power tools only with specifically designated
battery cartridges. Use of any other battery cartridges
may create a risk of injury and fire.
3.
When the battery cartridge is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects that
can make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
4.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
IMPORTANT SAFETY
INSTRUCTIONS FOR BATTERY
CARTRIDGE
1.
Before using battery cartridge, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively shorter,
stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out with
clear water and seek medical attention right away. It
may result in loss of your eyesight.
5.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive
material.
(2) Avoid storing battery cartridge in a container with
other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
6.
Do not store the tool and battery cartridge in locations
where the temperature may reach or exceed 50°C
(122°F).
7.
Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
10. Follow your local regulations relating to disposal of
battery.
Tips for maintaining maximum battery life
1.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room temperature
at 10°C - 40°C (50°F - 104°F). Let a hot battery
cartridge cool down before charging it.
4.
Charge the battery cartridge once in every six
months if you do not use it for a long period of time.
Save all warnings and
instructions for future reference.
3

Advertisement

Table of Contents
loading

Table of Contents