NOTE:
Choose suitable speed for the work load. Drilling
•
over the following capacity may damage the tool.
Steel
High speed
Wood
Steel
Low speed
Wood
012989
Screwdriver mode " "
CAUTION:
Adjust the number on the LED display to the proper
•
torque level for your work.
Make sure that the driver bit is inserted straight in
•
the screw head, or the screw and/or bit may be
damaged.
Hold the tool firmly. When the clutch cuts in or
•
refastening, a sudden twisting force may occur and
it can twist your wrist.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually.
NOTE:
This tool employs an electronic clutch. The tool
•
stops automatically when the clutch cuts in. To keep
operating, release the switch trigger once.
When driving wood screws, predrill pilot holes to
•
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
006421
NOTE:
See the following chart for the relation between the
•
number of torque setting and fastening torque rate.
The fastening torque rate will be different depends
on materials. Make a test fastening to get the
desired torque before operation.
Drilling capacity
6.5 mm
12 mm
10 mm
21 mm
Recommended size of pilot hole
(mm)
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
4.0 - 4.2
4.2 - 4.4
Number
on LED
Display
Low (1)
Approx. 2.5N m
1
(Approx. 25.5 kgf. cm)
Approx. 4.6N m
3
(Approx. 46.9 kgf. cm)
Approx. 8.1N m
5
(Approx. 82.6 kgf. cm)
Approx. 10.0N m
7
(Approx. 102.0 kgf. cm)
Approx. 11.5N m
9
(Approx. 117.3 kgf. cm)
012276
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before attempting to
perform inspection or maintenance except for the
following troubleshooting related to the light.
Never use gasoline, benzine, thinner, alcohol or the
•
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
•
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to
persons.
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Screw bits
•
Hook
•
Plastic carrying case
•
Various type of Makita genuine batteries and
•
chargers
NOTE:
Some items in the list may be included in the tool
•
package as standard accessories. They may differ
from country to country.
11
Fastening torque rate
High (2)
.
Approx. 1.1N m
(Approx. 11.2 kgf. cm)
.
Approx. 2.0N m
(Approx. 20.4 kgf. cm)
.
Approx. 3.0N m
(Approx. 30.6 kgf. cm)
.
Approx. 4.0N m
(Approx. 40.8 kgf. cm)
.
Approx. 5.8N m
(Approx. 59.1 kgf. cm)
or
attachments
Only use
accessory or
.
.
.
.
.
are