Specifications; Additional Safety Rules - Makita 6833 Instruction Manual

ENGLISH
1 Lever
2 Stopper base
3 Plate
4 Casing
5 Approx. 5 mm
6 Adjusting knob
7 Feeder box
8 Screw strip

SPECIFICATIONS

Model
Screw strip ....................................... 4 mm x 25 mm – 41 mm
-1
No load speed (min ) ...................... 4,700
Overall length .................................. 364 mm
Net weight ........................................ 1.9 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
9 Screw guide
10 Driving position
11 Reverse button
12 Hook
13 Lock button
14 Switch trigger
15 Reversing switch
16 Thumb screws
6833
17 Bit
18 Dust cover
19 Plain bearing
20 Wall
21 Extension handle
22 Limit mark
23 Screwdriver
24 Brush holder cap
6834
4 mm x 25 mm – 57 mm
2,800
396 mm
1.9 kg
OPERATING INSTRUCTIONS
Setting for desired screw length (Fig. 1)
There are 3 (for Model 6833 & 6836) or 5 (for
Model 6834) positive-lock screw length settings. To
obtain the desired setting, pull out the stopper base while
depressing the lever until you see the number of the
desired screw length (indicated on the plate) appear to
rest on the very top edge of the casing. See the table
below for the relation between the number indicated on
the plate and the respective screw length ranges.
Number indicated
on the plate
25/28
32
40
*51
*57
(Note) * for Model 6834 only
Adjusting the driving depth (Fig. 2)
Depress the stopper base as far as it will go. While keep-
ing it in this position, turn the adjusting knob until the bit
tip projects approx. 5 mm from the stopper base. Drive a
trial screw. If the screw head projects above the surface
of the workpiece, turn the adjusting knob in the A direc-
tion; if the screw head is countersunk, turn the adjusting
knob in the B direction.
Installing screw strip (Fig. 3 & 4)
Insert the screw strip through the screw guide. Then
insert it through the feeder box until the first screw
reaches the position next to the driving position.
Removing screw strip (Fig. 5 & 6)
To remove the screw strip, just pull it out in the direction
of the arrow. If you depress the reverse button, you can
pull out the screw strip in the reverse direction of the
arrow.
6836
4 mm x 25 mm – 41 mm
6,000
364 mm
1.9 kg
Screw length range
(mm)
25 – 28
28 – 35
35 – 41
41 – 51
51 – 57
5