Makita LF1000 Instruction Manual page 19

extrusion to prevent build-up of the aluminum
material on the blade.
CAUTION:
Never attempt to cut thick or round aluminum
•
extrusions. Thick aluminum extrusions may come
loose during operation and round aluminum
extrusions cannot be secured firmly with this tool.
Never cut aluminum in the table saw mode (bench
•
mode).
CUTTING AS TABLE SAW (BENCH MODE)
CAUTION:
Always use "work helpers" such as push sticks and
•
push blocks when there is a danger that your
hands or fingers will come close to the blade.
Always hold the workpiece firmly with the table and
•
the rip fence. Do not bend or twist it while feeding.
If the workpiece is bent or twisted, dangerous
kickbacks may occur.
NEVER withdraw the workpiece while the blade is
•
running. If you must withdraw the workpiece before
completing a cut, first switch the tool off while
holding the workpiece firmly. Wait until the blade
has come to a complete stop before withdrawing
the workpiece. Failure to do so may cause
dangerous kickbacks.
NEVER remove cut-off material while the blade is
•
running.
NEVER place your hands or fingers in the path of
•
the saw blade.
Always secure the rip fence firmly, or dangerous
•
kickbacks may occur.
Always use "work helpers" such as push sticks and
•
push blocks when cutting small or narrow
workpieces, or when the is hidden from view while
cutting.
Work helpers
Push sticks, push blocks or auxiliary fence are types of
"work helpers". Use them to make safe, sure cuts
without the need for the operator to contact the blade
with any part of the body.
Push block
120mm
300mm
130mm
1
6mm
50mm
1. Face/edge parallel
2. handle
3. Wood screw
4. Guide together
006080
300mm
130mm
3
9.5mm
50mm
8mm
4
Use a 19 mm piece of plywood.
Handle should be in center of plywood piece. Fasten
with glue and wood screws as shown. Small piece 9.5
mm x 8 mm x 50 mm of wood must always be glued to
plywood to keep the blade from dulling if the operator
cuts into push block by mistake. (Never use nails in push
block.)
Auxiliary fence
Fig.53
Make auxiliary fence from 9.5 mm and 19 mm plywood
pieces.
Ripping
CAUTION:
When ripping, remove the miter gauge from the
•
table.
When cutting long or large workpieces, always
•
provide adequate support behind the table. DO
NOT allow a long board to move or shift on the
table. This will cause the blade to bind and
increase the possibility of kickback and personal
injury. The support should be at the same height as
the table.
1. Adjust the depth of cut a bit higher than the
thickness of the workpiece. To make this
adjustment, refer to the section titled " Adjusting
the depth of cut ".
2. Position the rip fence to the desired width of rip
and secure in place by tightening the clamping
screw (A). Before ripping, make sure the two
screws of the rip fence holder are secured. If it is
not secured enough, retighten it.
3. Turn the tool on and gently feed the workpiece
into the blade along with the rip fence.
(1)
Fig.54
(2)
Fig.55
(3) When the width of rip is narrower than 65 mm,
2
50mm
Fig.56
100mm
19
When the width of rip is 150 mm and wider,
carefully use one hand to feed the workpiece.
Use another hand to hold the workpiece in
position against the rip fence.
When the width of rip is 65 mm - 150 mm
wide, use the push stick to feed the
workpiece.
the push stick cannot be used because the
push stick will strike the blade guard. Use the
auxiliary fence and push block.
Attach the auxiliary fence to the rip fence with
two "C" clamps.
Feed the workpiece by hand until the end is
about 25 mm from the front edge of the top
table. Continue to feed using the push block
on the top of the auxiliary fence until the cut is
complete.